Outriggers and 2 Step Recommendation to Replace Broken Step of 2018 Rockwood 2280BHESP

Question

Question:

I purchased a 2018 Rockwood 2280BHESP and during our first camping trip the steps broke from the frame welds failed. I want to replace them with a better installation with no weld if possible. Do I need some type of mounting brackets or hardware to replace 2 step manual pull out steps? Thanks.

asked by: Jim

0

Expert Reply:

We have outriggers like the part # LC301704 which make installing pull out steps like the Lippert Steps part # LC432682 much easier. Your appear to be broken at the weld.

The # LC301704 installs with included hardware.

expert reply by: Jameson C

0

Answer 1

We don't have an install video but what I can do is describe it. The portion of the #LC301704 with the round holes mounts to the bottom of the frame on your trailer with nuts and bolts or welding. They would need to be spaced at the width of your…

view full answer...

Answer 2

Yes, you can absolutely use the Prest-O-Fit Wraparound Exterior RV Step Rug #PR22FR with your TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear #TLA8102. These wraparound exterior rugs fit straight steps that measure 20" wide and…

view full answer...

Answer 3

The TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear - 4 Steps - 27-1/2" Base - 375 lbs #TLA8004 are a fit for your 2018 Grand Design Momentum 328M. They can be used to replace your current steps if desired. If you have factory…

view full answer...

Answer 4

There are 3 step pull out kits similar to the #LC432682 that you referenced but they are wider across the board so the exact mounting hardware you are using now won't work. The part #LC432690 would be a great solution for what you have but…

view full answer...

Answer 5

Yes, the Lippert Outriggers part #LC301704 are exactly what you described. These attach to the bottom of the trailer frame and provide brackets for the RV steps to attach to.

view full answer...

Answer 6

We don't have an install picture but what I can do is describe it. The portion of the #LC301704 with the round holes mounts to the bottom of the frame on your trailer with nuts and bolts or welding. They would need to be spaced at the width of…

view full answer...

Answer 7

I attached a picture that shows the install holes for the Outriggers part #LC301704. There are holes on both ends of the brackets for the steps and for attaching them to your RV. The #SM-01 would match up to the install holes of the Flexco Manual…

view full answer...

Answer 8

We do offer RV step outrigger mounting brackets, the Lippert #LC301704. These bolt on using included hardware. Part #LC301704 also fits only multi-step assemblies.

view full answer...

Answer 9

I do have a solution for you, but the closest thing that we have to what you are describing is the SolidStep Manual Fold-Down Steps #LC698799. This would be compatible with your door width but is only compatible with a threshold range of 27" -…

view full answer...

Answer 10

The side mounting bolt holes measure 7 inches apart on center for the Lippert Manual Pull-Out Step for RVs - Double - 7" Drop - 24-1/4" Wide #LC432682. From the bottom of the bracket to the bolt holes it is 9 inches, or from the top to the…

view full answer...

Answer 11

The Manual Pull-Out Step for RVs - Double #LC432682 has mounting holes that are about 24" x 7" and although there are not any with a 14" x 7" pattern, you can still use this step. In order to do so you have a couple of choices.…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Outriggers and 2 Step Recommendation to Replace Broken Step of 2018 Rockwood 2280BHESP

Product Page this Question was Asked From

Continue Researching