Mounting Hardware For The Fulton Plastic Fender with Top Step # F008551 Trailer Fender
Updated 03/03/2011 | Published 03/02/2011
Question:
what hardware do I need to install fender F008551 ?
asked by: Cliff
Expert Reply:
The Fulton Plastic Fender with Top Step, part # F008551, is designed to be mounted with your existing hardware, or mounted with brackets designed that are specific to the trailer frame on which they would be installed. No mounting hardware is included.
We do have some mounting hardware available that may work on your trailer (see link). You will need to determine the mounting location and style of bracket that will work on your trailer.
You may need to provide or fabricate any mounting hardware to mount the Fulton Fender # F008551. The dimensions of the fender are listed on the product page.
Product Page this Question was Asked From
Single Axle Trailer Fender w Top Step - Style C - Black Plastic - 8" to 12" Wheels - Qty 1
- Trailer Fenders
- Top Step
- 10 Inch Wheels
- 12 Inch Wheels
- 8 Inch Wheels
- 7 Inch Wide
- 21-1/2 Inch Long
- Plastic
- Bolt-On
- For Single-Axle Trailers
- Black
- Fulton
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Single Axle Trailer Fender w Top Step - Style C - Black Plastic - 8" to 12" Wheels - Qty 1
- Shop: Steel Spoke Trailer Wheel - 15" x 6" Rim - 5 on 4-1/2 - Galvanized Finish
- Shop: CE Smith Single Axle Trailer Fender - Gray Plastic - 8" to 12" Wheels - Qty 1
- Shop: Fulton Single Axle Trailer Fender - Black Plastic - 8" to 12" Wheels - Qty 1
- Search Results: trailer winch
- Search Results: bearing buddy
- Search Results: trailer wiring
- Search Results: trailer fenders
- Q&A: Adjusting Latch On Trailer Coupler with Trigger Latch
- Search Results: trailer fender brackets
- Video: All About the Mounting Bracket for Trailer Fender
- Video: All About the Bearing Buddy Bearing Protectors
- Video: A Closer Look at the Mounting Brackets for Trailer Fender
- Video: Bow Roller Assembly w/ Bells for 4" Wide Bracket Feature Review
- Video: Feature Review Single Axle Trailer Fender w Top Step
- Video: Checking Out the etrailer Boat Trailer Jack w/ Wheel
- Shop: Mounting Brackets for Trailer Fender - 8" to 12" Wheels - Pre-Galvanized Steel - Qty 2
- Shop: LED Identification Light Bar for Trailers over 80" Wide - Submersible - 9 Diodes - Red Lens
- Shop: etrailer Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 11" Lift - Zinc - 1.2K
- Q&A: Recommended Brackets to Mount Fulton Trailer Fenders # F008551
- Q&A: Do you Carry the Mounting Brackets to Line Up With the etrailer Single Axle Trailer Fender?
- Q&A: Replacement Fender for Yacht Club Jet Ski Trailer Measuring 20.5 Inches Between Mounting Holes
- Q&A: Diameter of the Replacement Footplate Keeper Pin for etrailer and Ram Square, Direct Weld Jacks
- Q&A: Which is Better for Highway Use 4.80-12 or 5.30-12 Trailer TIres
- Q&A: How Do The etrailer Single Axle Trailer Fenders Install?
- Article: Trailer Lighting Requirements
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Article: 30-Amp and 50-Amp RV Service: What's the Difference?
- Article: Trailer Wiring Diagrams
- Article: How to Measure for Travel Trailer and Fifth Wheel Steps
on Trailer Fenders
