Heated RV Camping Hose for Fresh Drinking Water

Question

Question:

OK, i cant find any info if this is for rv drinking water hoses. We will be in freezing weather and need to keep our water hose from freezing . This is a regular rv white hose used to connect drinking water to the trailer.

asked by: Karen Q

0

Expert Reply:

The Valterra AquaFresh Heated Fresh Water Supply Hose # W01-5315 is specifically designed to provide fresh drinking water in sub-zero temperatures.

expert reply by: Charles S

0

Answer 1

Yes, the RV Holding Tank Heater #372HTH-A that you referenced does have an adhesive backing

view full answer...

Answer 2

You will not want to install a heater like the RV Holding Tank Heater #372HTH-A between the metal straps supporting it and the tank as it can't be in contact with a conductive surface. This heater is 30" long x 13" wide but there are…

view full answer...

Answer 3

Hey Korey, That's a totally normal installation for the RV Holding Tank Heater #372HTH-A. My only word of advice would be to run a dedicated outlet for it to plug into with a switch somewhere in-line that's easy to access so you can cut power…

view full answer...

Answer 4

For your 50 gallon fresh water tank you will want to use two of the ThermaHeat RV Holding Tank or Step Heater Pad w/ Thermostat #277-000163 wired together. You can use the ThermaHeat Elbow Heating Pad #277-000161 as well, but this is a pad for 3 inch…

view full answer...

Answer 5

You can use the JR Holding Tank Heater #372HTH-A on your 30 gallon and 45 gallon tanks but you would need to use more than one per tank. On the 30 gallon tank you'd need to use two and on the 45 you'd need to use 3.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Heated RV Camping Hose for Fresh Drinking Water

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching