Replacement Front Wheel Holder for Yakima HoldUp Platform Bike Rack

Question

Question:

Hi, I need the front wheel holder... the complete arm in the silver color. I dont need the tray for the tire, etc. My rack was it by another vehicle and the plastic at the bottom of the arm cracked. Could you give me the part number and link? Thanks!

asked by: Joe

0

Expert Reply:

To fix your damaged HoldUp (models Y02433, Y02435, Y02434, Y02433-02435), you will need to replace the entire piece with the rear wheel holder assembly # Y90198 you were looking at.

I checked with Yakima and they informed me that they do not sell these parts separately due to the front wheel tray being captured in the arm assembly of the rack when it is being manufactured and there is no way to get it out without damaging the rack.

If you instead need the front wheel holder assembly you will want part # Y90197.

I have linked the above mentioned products to this page for your viewing and purchasing convenience.

expert reply by: Jackie C

0

Answer 1

I checked with Yakima and for your older model Yakima Holdup for a 1-1/4 inch hitch the correct hitch pin is the part #Y8880129.

view full answer...

Answer 2

Since the lock number of your hitch lock is only listed on the side of the lock core, and yours is locked and therefore not accessible, the only solution is to replace what you have with a new hitch bolt and lock. For that you'd need part…

view full answer...

Answer 3

Thanks for the photos! Those definitely helped in identifying what bike rack you have. Looks like you have the Yakima HoldUp so if you have the rack with the 1-1/4" shank #Y02445 then the set you need is part #Y8890176, but if you have the rack…

view full answer...

Answer 4

Easiest way will be based on what bike rack you have. Could you get me that info and I can check to see which pin you'd need for a replacement.

view full answer...

Answer 5

We do carry replacement end caps for the Yakima HoldUp Bike Carrier. For an original HoldUp carrier you can order part #8880222. The other end cap we offer, part #8880228, will fit all HoldUp bike carriers and is designed for use with the bike…

view full answer...

Answer 6

In order to converter a Yakima HoldUp for 1-1/4" to a Yakima HoldUp for 2" you will need the Replacement Tongue for Yakima HoldUp Bike Racks part #8880580 and the Replacement Hitch Bolt part #Y8890200. The lock core housing can be reused.

view full answer...

Answer 7

For your Yakima HoldUp 2 Bike Rack for 1-1/4" Hitches - Platform Style - Tilting #Y02445, the Replacement 2" Hitch Adapter for Yakima Carriers #Y8890174 will not work according to my contact at Yakima and it is no longer available. Instead…

view full answer...

Answer 8

I have an option for you, but no, the #8880519 will not work on the shank of your Yakima bike rack that you sent me a picture of. The only option for you is a reducer that installs in your 2" trailer hitch receiver like the #HT02, and then will…

view full answer...

Answer 9

The Replacement Aluminum Hitch Adapter Sleeve for Saris 1-1/4" Hitch Bike Racks #SA3032 is not the best option for you. There is not a shank adjustment sleeve like that for your Yakima Holdup. You would either want the 2 inch shank #8880580 or…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Replacement Front Wheel Holder for Yakima HoldUp Platform Bike Rack

Continue Researching