Will the Dutton-Lainson Winch Mounting Plate # DL24059 Fit a Trax Electric Winch

Question

Question:

WILL A TRAX 3500 ELECTRIC WINCH FIT THIS BRACKET

asked by: Roger A

1

Helpful Expert Reply:

I am not familiar with the Trax Electric Winches so I am not sure what their mounting plates look like. However, the Dutton-Lainson winch mounting plate # DL24059 has the top 2 holes spaced 2-1/2" apart. Then the third hole in the middle is down 3" from the center line between the top two holes.

If your Trax 3500 Electric Winch plate has the same dimentions, this mounting plate will fit your winch. I attached a diagram outlining the dimensions for your convenience.

expert reply by: Sarah H

1

click to enlarge

Answer 1

I went out to the warehouse to measure the Dutton-Lainson Angle Mounting Plate, #DL24059. The internal width of the U-bolt is 3-1/6 inches. The length is 5 inches. As long as the post is 3 inches wide by 4 inches deep, it will fit. I also spoke with…

view full answer...

Answer 2

I have some great electric boat trailer winch options for you such as the Dutton-Lainson StrongArm Electric Winch which is what I recommend. These will need to be rated for about half the weight of the boat, so part #DL25215 for example (full…

view full answer...

Answer 3

The Dutton-Lainson StrongArm Electric Trailer Winch - Marine - 1,500 lbs #TW4015 requires a winch stand or mounting bracket. For the StrongArm you can use the Dutton-Lainson Mounting Adapter Plate for StrongArm Electric Winches #DL24055 if you have a…

view full answer...

Answer 4

The Dutton-Lainson StrongArm Electric Winch #DL25215 doesn't come with a mounting plate but you can use part #DL24055 or #DL24059 if your current mounting bracket doesn't match with the mounting hole pattern for this winch (see attached).

view full answer...

Answer 5

As the Dutton-Lainson Hand Winch #DL17042 is typically mounted to a horizontal post or beam on a trailer, we will not have a bracket to mount it vertically. That being said, you may be able to adapt the Dutton-Lainson Mounting bracket #DL24059 to…

view full answer...

Answer 6

I spoke to my contact at Dutton Lainson and they informed me that the Dutton Lainson Adapter plate part #DL24059 that you referenced is 7.7 inches long and 5.50 inches wide.

view full answer...

Answer 7

It sounds like you are looking for the CE Smith Winch Stand - Galvanized Steel - 30" Tall x 2" Wide #CE31013G. This is designed for a 2 inch by 3 inch frame, so you will need to make some modifications. This is the only winch stand we…

view full answer...

Answer 8

Hey Micah! Pacbrake has actually been around for a long time, more than 60 years. We have had customers ask for these air bags in the past, and we've seen them on vehicles coming in. Until now, Firestone has been the go to since their quality is…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Hello Jeff, Sounds like you’ve got a big camper (about 4,000 lbs) on your 2024 F-350 dually, and when it’s loaded, the truck feels bouncy and sways a bit. That’s pretty common with heavy campers, especially if the suspension is still stock.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...