Location of Wiring Harnesses Plug for 2016 Subaru Outback Limited
Updated 05/16/2016 | Published 05/12/2016 >
Question:
I had just purchased a class III hitch and wiring harness from you and went to begin installing the wiring today. After watching the video and reading the instructions I took the panels out as shown but was unable to find the plug described in the instructions under the panels. Reached under the side panels and everywhere I could get my hand. No plug? Is there someplace else other then the drivers side youve found them? Thanks for your help
asked by: Bruce H
Expert Reply:
I spoke to one of our installers and he informed me that on the Outback we had in our shop that the plug could easily have been overlooked, as it was taped to another bundle of wires under the panel. If you look at the video I've linked at the 2:00 minute mark, you will see Randy push the connector back under that panel, he told me he had to reach around under there to find the plug before they begun the video.
I found another source that mentioned that the plug will not only be tucked up behind the driver side inner fender trim but it should be visible near the rubber grommet in the floor and the cargo anchor. I have attached an image of this location to the page for you to better see. Very similar area pointed out in your # 118467 instructions.
In past years the plug has been known to be on either the driver or passenger side, but from the vehicles we've had here to test fit all have been on the driver side.
Let me know if you still can't find it after this, I would be more than happy to help you further.
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Q&A: Adding Electric Brakes to 1977 Scamp Trailer with Lippert Torsion Axle
- Q&A: Parts Needed to Install Brake Controller on 2016 Subaru Outback LTD
- Shop: Brake Controller
- Video: How to Install etrailer Trailer Brake Controller 7-Way RV Upgrade Kit - 2025 Subaru Outback Wagon
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Search Results: tekonsha p3
- Search Results: redarc trailer brake controller
- Search Results: red arc brake controller
- Search Results: red arc liberty
- Search Results: etbc7 kit
- Shop: Trailer Wiring
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Curt Trailer Connector Adapter with Backup Alarm - 4-Way to 7-Way RV and 4-Way Flat
- Shop: Curt Spectrum Brake Controller w/Universal Harness - Dash Mounted Knob - 1 to 4 Axles - Proportional
- Shop: Curt 7-Way to RV Socket LED Circuit Tester - Vehicle End
- Video: Detailed Breakdown of the Curt Trailer Connector Adapter with Backup Alarm
- Q&A: Dexter 8-247-Hub Bearing Buddy and Bearing Kit Fit
- Search Results: rocker switch
- Search Results: switch
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2021 Subaru Ascent
- Video: Feature Review Curt Universal Wiring Kit for Trailer Brake Controllers
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What Size Socket Works with 1 Inch Spindle Castle Nut # 165686?
- Q&A: Size of Spindle/Castle Nut for an 84 Spindle
- Q&A: Which Grease Cap And Spindle Nut Do I Need For Bearing Kit # BK2-100
- Q&A: Spindle Nut Size For EZ Lube Axles
- Shop: Vehicle Sway Bars

