Does the Demco Trailer Coupler # DM15791-97 Have to be Painted

Question

Question:

Does this need to be painted?

asked by: Joe

0

Expert Reply:

The coupler part # DM15791-97 that you referenced comes primed for paint, but if you didn't want to paint it you could leave it as-is.

A better option would be the galvanized version of this # DM07678-95.

expert reply by: Jameson C

0

Answer 1

The #BLTL-23 Blaylock coupler lock is compatible with a very specific type of coupler, the CollarLok like our part #BD028499, so it wouldn't be a good fit for a coupler like the Demco #DM14040-81. A lock like the #FA86-0015-316 or a latch type…

view full answer...

Answer 2

If you had a pin lock inserted in the coupler part #DM14040-81 that you referenced it would not auto-latch onto the hitch ball. The latch portion would not be able to slide up to let the ball pass. If you check out the picture I attached you can see…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

Hey Richard, yes the hardware kit part #DM68UV is correct hardware kit for the Demco Trailer Coupler #DM88XR. That curve shape in the corners of the coupler are compensated for with the hole design in the coupler. Do you have the channel already…

view full answer...

Answer 8

Hi Jim, the honest answer is that there isn’t a direct replacement or rebuild kit still available for the TDE LP8000, so the right path forward is to replace the entire actuator, which typically means cutting the old one off and installing a new…

view full answer...

Answer 9

The Hydrastar Vented Marine Electric Over Hydraulic Actuator for Disc Brakes #HS481-8067 is designed to be completely plug-and-play so the female end of the 7-way would need to connect to the 7-way cable that's already installed on the trailer…

view full answer...

Answer 10

The Demco Hydraulic Brake Actuator #DM8750311 can be used to replace your Tie Down Engineering LP8000 actuator. The Demco comes with an electric lockout like you are wanting. It is zinc coated for corrosion resistance and fits a 2-5/16" hitch…

view full answer...

Answer 11

I have a clevis hook that may work with your 5,000 lb trailer. Take a look at part #6495-401-04. This hook has a working load limit up to 5,400 lbs and the pin that connects through the chain is 7/16 of an inch in diameter. We have heavy-duty clevis…

view full answer...

Answer 12

Hey Paul, Slip Hooks like the #DU93UR feature a safety latch to prevent he chain from being able to back off of the hook if the chain became loose. Grab hooks like #DU66UR don't have the safety latch feature but have a thinner opening, which…

view full answer...

Does the Demco Trailer Coupler # DM15791-97 Have to be Painted

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching