What is a Draw Bar and Is It Needed to Install Trailer Hitch 24847

Question

Question:

What is a draw bar? And do I need it in order to have the trailer hitch installed? I own a 2015 Toyota Prius Liftback.

asked by: Helen T

0

Expert Reply:

A drawbar (or sometimes called ball mount), is the metal piece that slides into the hitch opening to provide the attachment point for a hitch ball for trailer towing.

If you have no plans of towing with the part # 24847 then you would not need the draw bar.

expert reply by: Jameson C

0

Answer 1

Hi Daniel; is there a specific measurement on the #BW54FR you're looking for? I can tell you the overall height is 13-3/4" and length is 14". The distance from the center of the hitch pin hole to the to center of hitch ball is either…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 11

Hi Richard! From the top of the shank to the lowest part where the tri-ball sits on the #BWTS20067BMP is 11.125". If you have the balls at max drop with the tallest one hanging down that would be 12.5". We recommend at least 11" of…

view full answer...

Answer 12

Thanks for the information Gil! The best ball mount options for your 2022 Ford F-350 duallys 3" factory hitch are the B&W Tow & Stow 2-Ball Mount item #BWTS30040B or the Tow & Stow 3-Ball Mount item #BWTS30049B. These ball mounts…

view full answer...

What is a Draw Bar and Is It Needed to Install Trailer Hitch 24847

Continue Researching