3-Hole Mounting Bracket for 2 Inch Round LED Trailer Marker Lights

Question

Question:

WANT TO mount center rear marker light on back of trailer, do you sell 3 hole bracket to weld on bumper? Want to use 2inch diameter led markerred lights Thank You

asked by: Larry

0

Expert Reply:

We have 2 inch clearance/marker light # MCL52AB which has a 3 hole bracket. The powder coat would have to be sanded away to weld it to the trailer.

We do have bracket # BK5557GB that will hold the 2 inch round lights but it can't be welded on. It comes with hardware to surface mount it.

expert reply by: Michael H

0

Answer 1

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 2

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 3

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 6

The exact replacement hub assemblies you need for your BD2-545-17 are the etrailer Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 #AKHD-545-35-K that you referenced.

view full answer...

Answer 7

The manufacturer of a trailer can sometimes confirm specific parts using the trailer's VIN but the best way to know what replacement bearings and seals you need is to pull one of the hubs and to remove those parts. Then it is usually easy to find…

view full answer...

Answer 8

Hey Mike, this is a pretty common issue with newer vehicles and LED trailer taillights unfortunately but there are ways to fix it. You can swap the trailer lights to incandescent like you mentioned or you can add load resistors like the part #ARC22VR…

view full answer...

Answer 9

Hey Aaron, Unfortunately that master cylinder from Attwood is no longer made and cannot be replaced. For that you would need to replace the whole actuator. The closest replacement we carry for that is going to be the Demco #DM72VR brake actuator.…

view full answer...

Answer 10

I've linked a help article that will give you the common color coding but on your trailer I wouldn't go by it. Even if they are correct you just never know so I suggest testing it. To test it cut off the 5-way connector that's on there…

view full answer...

Answer 11

The item you selected, Sealed 2-1/2 Trailer Light, part #MC57AB, is a 2-1/2 inch light that will mount into a 3 inch hole using 2-1/2 inch grommet, part #A55GB. The hole size to mount a 2 inch round light flush mounted would be 2-5/16 inches. The…

view full answer...

3-Hole Mounting Bracket for 2 Inch Round LED Trailer Marker Lights

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching