Is a Dexter Elec./Hydraulic Brake Actuator Damaged if it was Ran Dry

Question

Question:

I had a trailer with 2- 5200 # axles, and after a 500 mile trip the fluid had leaked out and was dry , I re filled and fixed the fitting leak , and re bleed the brakes , they work fine , did I do any damage to the actuator , # TQA29933 thanks

asked by: Ed W

0

Expert Reply:

I spoke with my contact at Dexter and when I explained to him your situation he said you are totally fine.

He said that the actuators will be totally fine if they were temporarily ran dry.

expert reply by: Jameson C

0

Answer 1

I spoke with my contact at Dexter and when I explained to him your situation he said you are totally fine. He said that the actuators will be totally fine if they were temporarily ran dry.

view full answer...

Answer 2

Thank you for the picture, it is helpful. I can see that you have an actuator for disc brakes. In the picture you can see the yellow label that says "disc brake actuator for use with disc brakes only". The coupler does not differentiate…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Is a Dexter Elec./Hydraulic Brake Actuator Damaged if it was Ran Dry

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching