Measurements of Stake Pocket Tie-Down Anchor for Flatbed Truck or Trailer # T35Z or # T355

Question

Question:

Actual size 0f post supports

asked by: James

0

Expert Reply:

The Stake Pocket Tie-Down Anchor for Flatbed Truck or Trailer # T35Z or # T355 measure 5-1/4 inches from the bottom up to the bottom of the top plate the D-ring is on. They are 3-1/2 inches wide and 2 inches deep. They are designed to fit in 2x4 stake pockets.

expert reply by: Michael H

0

click to enlarge

Answer 1

Tie-down anchors for truck bed stake pockets like the Erickson Retractable Tie-Down Anchors #EM01003 referenced in your question are designed to fit most truck bed stake pockets. I have attached an image showing the dimensions of this product so you…

view full answer...

Answer 2

If the inner width of your flatbed trailer's stake pockets are 3-1/2" then you're going to want the Brophy Stake Pocket Tie Down Anchor item #TL2B you were looking at. The dimensions are 8-1/4" tall x 3-1/2" wide x 1-1/2"…

view full answer...

Answer 3

The Buyers Products Stake Pocket Spare Tire Carrier #3375201012 fits most standard 3-1/2 in. and 3-3/4 in. stake pockets. It is compatible with 5 on 4-1/2 inch, 5 on 5 inch, 6 on 5-1/2 inch, and 8 on 6-1/2 inch bolt patterns.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Measurements of Stake Pocket Tie-Down Anchor for Flatbed Truck or Trailer # T35Z or # T355

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching