How Many Bolts Get Used to Install a RotaFlex Pin Box on a Trailer

Question

Question:

How many bolts do you have to use to mount to trailer on a rotoflex 18k, it has 3 in the front row and 2 in the back row for each side. Can I the pin box one hole and mount with 2 in the front and 2 in the back on each side.

asked by: James S

0

Expert Reply:

When you attach a RotoFlex pin box like the part # LC328330 you will need to use the same amount of bolts per side of the pin box like that the original pin box used to secure to the trailer frame.

Some setups will require only 4 bolts and some may require 5 or 6. It really depends on the trailer and what was originally on the trailer.

expert reply by: Jameson C

0

Raymond H.

3/20/2020

Can I lower the Lippert Rota Flex pin box by one bolt space to cause nose to be higher?

Chris R.

3/22/2020

The Lippert Rota Flex pin box can indeed be lowered on your existing flange brackets just like your existing pin box could, assuming it's not already on its lowest setting. This is a simple way to to create a level ride when hooked up to your truck.

Answer 1

Hey Mike, The Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box #GY48GR requires 5/8 x 1-1/2" grade 8 bolts and nuts that need to be torqued to 160ft/lbs. You'll want to use a minimum of 4 bolts per side.

view full answer...

Answer 2

Hello Everett, thanks for reaching out. Sadly, we do not offer the replacement locking handles for the B&W Companion 5th Wheel Hitches. If you reach out directly to B&W they should be able to provide the parts you need. They will likely ask…

view full answer...

Answer 3

I do have an option for you but we do not offer a replacement shock absorber for the B&W Companion OEM 5th-Wheel Hitch part #BWRVK3300. The option we do have however is a new head, the Replacement Head Assembly for B&W Companion 5th Wheel…

view full answer...

Answer 4

Kenny, those bolts for the B&W Companion 5th Wheel Trailer Hitch #BWRVK3500-5W should be torqued to 40 ft. lbs. Also, the pivot arms would need to be torqued to 80 ft. lbs, the draw down bolt should be tighten to 60 ft.lbs and the arms should be…

view full answer...

Answer 5

Hey Mark, there is no torque specs for those puck bolts on the B&W Companion OEM 5th-Wheel Hitch for Ford Super Duty Prep Package #BWRVK3300. You're just going to need to loosen that nut on the bolt enough to where you can operate the locking…

view full answer...

Answer 6

I spoke to my contact at B and W and she said that sticker you have on your B and W Companion was put on your hitch by mistake. The older style of Companion used 40 ft/lbs and a few of the newer style hitches went out with the older sticker. You will…

view full answer...

Answer 7

Between 4 and 6 inches is typically what is recommended as minimum clearance from trailer overhang to bed rails. If you can level your setup by lowering hitch where you'd have 5 inches you should be fine. Especially if you aren't in an area…

view full answer...

Answer 8

You'll need to have three bolts in the front and two bolts in the back of your Trailair Air Ride 5th Wheel Pin Box #LC158778 to prevent any flex in the mounting ears of your trailer's frame. This means you'll need to move the pin box back…

view full answer...

Answer 9

The reverse light pin on a traditional 7-way trailer connector, like part #PK11893 or a factory connector if that's what you have on your 2018 Ram, is the center pin. Take a look at the picture I attached that shows all the pin functions. To add…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

How Many Bolts Get Used to Install a RotaFlex Pin Box on a Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching