Putting Titan Model 10 Trailer Brake Actuator Back Together
Published 06/02/2015
Question:
I bought this part to replace a smashed outer sleeve on my boat trailer hitch and didnt know it was sold as one unit I only needed the outer sleeve. Anyway, when I took off the master pins to take out the outer sleeve, as I pulled the sleeve out, the two rear rollers dropped down and were free. Now, I am trying to replace the broken outer sleeve, and cant get the rear rollers lined up with the holes on the dampers I cant get my fingers up in there and still slide the sleeve in. Any suggestions? My trailer is a 2008 Metal Craft trailer. I am pretty certain this is the exact part #T4750800 I bought through a local parts dealer.
asked by: Bill S
Expert Reply:
You will pretty much have to remove as much as you can from the interior of the Titan model 10 actuator # T4750800 to be able to get to the parts you need easily. You will have to remove the master cylinder and components forward of it but be careful not to pull the break away cable out too far because then it has to be reset and that is a whole other issue.
I have included a link to the installation details that does explain the process of putting the actuator back together. It is in the latter parts of the instructions. that and the parts breakdown and diagram should be a tremendous help.
Product Page this Question was Asked From
Dexter Zinc-Plated Brake Actuator - Disc - 2-5/16" Ball - Bolt On - 12,500 lbs
- Brake Actuator
- Surge Brake Actuator
- Boat Trailer
- Construction Trailer
- Farm Trailer
- Travel Trailer
- Utility Trailer
- Bolt-On
- 12500 lbs GTW
- 2-5/16 Inch Ball Coupler
- 3 Inch Channel Tongue
- Disc Brakes
- No Lockout
- Dexter
more information >
Continue Researching
- Video: Review of Demco DA10 Manual Lockout Kit Hydraulic Brake Actuator - DM48UV
- Video: Let’s Check Out the Manual Reverse Lockout Kit for Demco Hydraulic Trailer Brake Actuators
- Shop: Demco DA10 Manual Lockout Kit for Hydraulic Brake Actuators
- Shop: Demco Hydraulic Brake Actuator w/ Drop - Drum - Zinc - 2-5/16" Ball - 12,500 lbs
- Shop: Manual Reverse Lockout Kit for Demco Hydraulic Trailer Brake Actuators
- Video: In-Depth Review of the Replacement Shock for Dexter Model 6 and 10 Brake Actuators
- Q&A: Where Do the Rubber Bearings Go On the Titan/Dico Model 10 Surge Brake Actuator
- Shop: Bearing for Dexter Model 6 Actuator
- Article: How to Bleed Your Trailer Surge Brakes
- Shop: Bearing - Top & Bottom - for Dexter Model 10 Actuators
- Q&A: Amount of Play on Dexter 12K Torflex Axle Under Max Load
- Search Results: wheel cylinders
- Shop: etrailer 7-Way RV Style Connector with Molded Cable - Trailer End - 6' Long - RV Standard
- Shop: Curt Cold Weather 7-Way RV Style Connector - Trailer End - 10' Long - RV Standard
- Search Results: replacement foot pad
- Search Results: boat trailer winch
- Q&A: How to Replace the Shock on a Titan Model 10 Surge Brake Actuator
- Q&A: Diagram for Replacing Titan Model 10 Actuator Shocks
- Q&A: Roller Placement on Shocks for a Titan Model 10 Brake Actuator
- Video: Breaking Down the Dexter Zinc-Plated Brake Actuator
- Q&A: Troubleshooting a Leaking Reverse Lock Out Solenoid
- Q&A: Disc Brake Upgrade on a 2012 Tandem Axle Boat Trailer
- Search Results: brake actuator accessories and parts
- Video: An In-Depth Look at the Replacement Breakaway Lever for Dexter Model 10 and 20 Actuators
- Video: Review of Dexter Replacement Cable for Dexter Breakaway - T2385500
- Video: Trailer Wheel Measurements
- Article: Trailer Tire Sizing
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Shop: Trailer Hitch
on Brake Actuator
