Can Optronics GloLight - Sealed, 2 Round Trailer LED Clearance/Side Marker Light be Surface Mounted

Question

Question:

Can the optronics marker glolights be surface mounted or for it have to be flush mount?

asked by: Kent

0

Expert Reply:

You can make Optronics marker light # MCL155AB a surface mount light by using bracket # BK5557GB. You will also need wiring harness pigtail # A46PB.

expert reply by: Michael H

0

Answer 1

We have 2 inch clearance/marker light #MCL52AB which has a 3 hole bracket. The powder coat would have to be sanded away to weld it to the trailer. We do have bracket #BK5557GB that will hold the 2 inch round lights but it can't be welded on. It…

view full answer...

Answer 2

You will need to cut a 2-5/16 inch mounting hole for installation of the 2 inch Round Flush Mount Grommet, item #A54GB, and the Sealed, 2 inch Round Trailer Clearance and Side Marker Light, item #MC53RB. The proper wiring pigtail for this light is…

view full answer...

Answer 3

Thanks for the picture of the trailer wiring connector you have. Based on that you are in need of a 7-way blade extension like the part #C56080 for a 7 foot long extension or part #HM20049 for an 8 foot long extension. Or if you are looking for…

view full answer...

Answer 4

Either way is correct. It depends on if you want to keep the semi-style 7-Way (if you need to tow that type of trailer) or if you will never be towing a semi-trailer. If you need to keep the 7-Way semi active on the truck, then you would need to make…

view full answer...

Answer 5

Numbers on trailer light lenses usually refer to DOT codes, not the light manufacturer's actual part number for the item. The light part number is usually on the light's base, which typically is less likely than the lens to be damaged or to…

view full answer...

Answer 6

Both the Rubber Grommet #A45GB and the Notched Rubber Grommet #A45GNB that you referenced will fit and work well with the Optronics 4" Round LED Light #STL55RB. The only difference between the two grommets, as you mentioned, is the notched cut…

view full answer...

Answer 7

To mount the Optronics Trailer Light, #MC57AB, in a rubber grommet you would use the Optronics 2-1/2 Inch Round Grommet - Flush Mount, #A55GB. This grommet will require a 3 inch mounting hole. To mount the Optronics Miro-Flex, Sealed, 4 Inch Round,…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Can Optronics GloLight - Sealed, 2 Round Trailer LED Clearance/Side Marker Light be Surface Mounted

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching