How Does the Submersible, Under 80" LED Trailer Light Kit part # TLL9RK Wire to Trailer

Question

Question:

do you have a wiring diagram for the TLL9RK. And what is the stud spacing on the lights?

asked by: Mike

0

Expert Reply:

For the assemblies that come with the Submersible, Under 80" LED Trailer Light Kit part # TLL9RK that you referenced the white wires will need to be grounded, the brown wires will run to the running lights circuit, the green wire will run to the right stop/turn circuit and the yellow wire will run to the left stop/turn circuit.

I attached a picture that has a standard trailer wiring diagram that should be helpful for you.

The distance between the mounting studs is 2 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Optronics stud-mounted LED Trailer Light Kit, part #TLL9RK, features left- and right-hand LED light assemblies that are DOT-approved and waterproof, and includes a 25-foot wiring harness, mounting hardware and connectors, and a license plate…

view full answer...

Answer 2

You are going to have to pull a hub off your trailer to determine if the hub you referenced would fit it. We have to match either spindle dimensions or bearing numbers to know if the part #AKIHUB-440-2-1K is a correct replacement. The bearings of…

view full answer...

Answer 3

Hey Russ, sorry for any confusion but the trailer taillight kits we offer like the Optronics part #TLL9RK that you referenced all use standard 4-way connectors. So they would plug right up to the 4-way of your vehicle.

view full answer...

Answer 4

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 5

Hey, thanks. You're not so bad yourself! Going to a larger tire size is possible but there are a few things to think about. Chief among these things is clearance. When going from an 8 inch tire to a 12 inch tire the diameter will increase by 4.4…

view full answer...

Answer 6

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 7

First, make sure that you stay within the gross trailer weight capacity for your trailer. If that 200 pounds extra puts you over the gross trailer weight capacity then you will want to carry that extra weight in the vehicle. Going with a higher…

view full answer...

Answer 8

Standard trailer wiring circuits on 7-ways like the part #C58155 and #PK12706 are rated for up to 40 amps so if you wanted to use a 7-way like this to power a horn that is rated for 13 amps you certainly could.

view full answer...

Answer 9

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 10

This is an torsion axle on your 2005 Wesco 128. You also think the axles are rated for between 3,000 lbs and 3,500 lbs. Without your specific axle model, I can only speculate which hubs and bearings you need based on the information you provided. For…

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

While there is a similar option for you, the Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Galvanized #AKIHUB-545-2-G-1K is only for 10" to 12" wheels. For an option that will work with 8" wheels, uses the same L44643…

view full answer...

How Does the Submersible, Under 80" LED Trailer Light Kit part # TLL9RK Wire to Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching