Curt Venturer NEXT Trailer Brake Controller - 1-3 Axles - Time Delayed
Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In
Part Numbers: C74VV,C51322
Retail:$143.17
Our Price: $101.44
You Save: $41.73
This item qualifies for Free Shipping
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Curt Venturer NEXT Trailer Brake Controller - 1-3 Axles - Time Delayed
part number: C74VV
A simple LED display and a pinch-trigger manual override make this time-delayed brake controller easy to read and easy to use. Installation is quick and simple with no mounting restrictions. Activates brakes with a preset intensity.
Features:
- Brake controller activates trailer brakes with preset intensity
- Adjustable power output control lets you select the amount of braking force
- Rocker switches located on left front of module for easy access
- 10 Gain settings and 9 load settings allow you to adapt to various driving conditions
- Select a higher setting for harder braking and lower for more gradual braking
- Pinch-trigger manual override is within easy reach for controlling trailer sway or stopping in emergencies
- Simple LED display shows the amount of power output
- Self-diagnostics monitor trailer connection and check for shorts
- LCD display shows power adjustments in 1.0 increments
- Brightness is adjustable for optimal visibility
- Auto-sleep mode prevents battery drain after 5 minutes of idle time
- Quick and easy installation with no mounting restrictions
- No need to mount level - install anywhere at any angle
- Included mounting bracket and hardware designed to hold brake controller flush against the dash
- Plug-in, vehicle-specific brake control adapter (sold separately) available for select vehicles to reduce installation time
Specs:
- Application: trailers with up to 3 axles (6 brake assemblies)
- Compatible with low-volt, PWM, ABS, cruise control, and electric-over-hydraulic trailer brakes
- Dimensions: 4" long x 3-1/8" wide x 1" thick
- Limited lifetime warranty
Gain Adjustment
Gain control lets you set the maximum amount of power that will be applied to your trailer's brakes, adjusting in increments of 1. How much braking output you need is determined by the weight of your trailer; a heavier trailer will need more power to bring it to a stop. You want to go as high as you can without the trailer brakes locking up. Typically, the gain is only readjusted when you experience changing road conditions or if the weight of your trailer changes. To get more power to your brakes, press the left-hand upper rocker switch. To decrease the gain, press the lower switch. When you make your adjustment, the gain setting will show on the LED screen for 5 seconds as a series of bars and then go into sleep mode to reduce drain on the battery.
Load Control
Once you have the gain set, you can fine-tune your braking by adjusting the load control on a scale of 1 to 9. This controls the aggressiveness of your trailer's braking, meaning how quickly the brakes reach the maximum braking level. Load control can get the braking power to your trailer faster and with more intensity so that it doesn't push your tow vehicle forward. If your vehicle takes too long to come to a stop, increase the setting by pressing the right-hand upper rocker switch. If it stops too abruptly, decrease the setting by pressing the lower switch. You can alter the setting to suit your driving preferences or to improve handling based on changing road conditions or varied trailer loads.
Pinch-Trigger Manual Override
The Venturer comes with a easy-to-reach, pinch-trigger manual override, great for stopping sway or controlling your trailer's momentum in emergencies. To engage the manual override, just push in the trigger. This will activate the trailer's brakes and brake lights without you having to apply the brakes on your tow vehicle, perfect for limiting trailer movement while you're cruising.
LED Display
The LED display on the Venturer is large and easy to read at a glance. It will show you what setting the brake controller is on as well as give you information for troubleshooting. You can adjust the screen brightness or trigger night mode so it won't glare obnoxiously on your dash. Press the control button to cycle through the different modes, shown as a bar - keeping it simple.
Quick Installation
Because inertia plays no role in the functioning of this controller, you do not have to mount the unit at any particular angle. Your mounting options are limitless, so long as you can still easily access the controller and the manual override. The included bracket is designed to mount the brake controller flush to the dash so it takes up almost no space at all.
If your vehicle already has a plug-in brake controller wiring harness, just connect the unit to it. Otherwise, you will need to purchase a vehicle-specific wiring harness (sold separately) to plug into. If a harness is unavailable for your vehicle, hardwiring will be necessary.
Note: If a custom brake control wiring adapter is not available for your vehicle, one of the following will be required:
20-Amp circuit breaker (9506P - sold separately) for 2- to 4-brake applications
30-Amp circuit breaker (38630 - sold separately) for 6- to 8-brake applications
See also etrailer.com's exclusive 7- and 4-way brake control installation kit (ETBC7 - sold separately) if you don't already have a 7-way plug at the back of your vehicle.
Time-Delayed Braking
The Curt Venturer NEXT comes equipped with time-delayed braking. Every time you apply the brakes in your vehicle, a signal is sent - via the brake switch - to the Venturer. The controller then sends power out to your trailer brakes to activate them with an intensity set by you, at a rate determined by you. Both the amount of braking power (gain) and rate of application (load) can be adjusted to suit your preference, the road conditions, the type of trailer, and the weight of your load. To determine which levels are best for your application, test your towing setup and choose what feels right.
51116 Curt Venturer NEXT Time Based Trailer Brake Control - 1 to 3 Axles
Replaces Curt 51110
Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In
part number: C51322
Install your Curt electric trailer brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in port beneath your vehicle's dash.
Features:
- Plug-in wiring adapter allows for quick, simple installation of your electric trailer brake controller
- No cutting or splicing required
- Custom connector end plugs into the built-in port beneath the dash of your vehicle
- Other end plugs into the back of your electric brake controller
- Compatible with time-delayed and proportional brake controllers from Curt
- Brake controller must have built-in plug for adapter to connect - will not work on controllers with pigtail wiring harnesses
- 2' Long, 12-gauge wires have protective covering to deter damage
- Limited 1-year warranty
Installation of Curt Brake Controller Adapter
To install your Curt electric brake controller, you need to connect the wiring of the controller to your vehicle. Certain auto manufacturers offer pre-wired options, typically known as tow packages, wherein wiring is run for you from the dash to the trailer connector on the back of your vehicle. When this is done, a port is installed at your dash so that you can easily plug in a brake controller.
This adapter plugs into the port on your vehicle's built-in brake control wiring harness. For most applications, this harness is located beneath the dash, near the center console.
No hardwiring is required to install this adapter. After you plug it into the factory port, you simply plug the other end of the adapter directly into your electric trailer brake controller. Because there are no wires to connect, installation is not permanent. You can unplug and remove your brake controller at any time to transfer it to another vehicle or securely stow it away.
51322 Curt Quick Plug Brake Control Adaptor Harness
California residents: click here
Customer Satisfaction Score:
96% were satisfied with this product
4% of customers were not satisfied
- Alternate product found
- Defective
- Product did not meet expectations
Customer Reviews
Curt Venturer NEXT Trailer Brake Controller - 1-3 Axles - Time Delayed - C74VV
Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In - C51322
Average Customer Rating: 4.8 out of 5 stars (276 Customer Reviews)
A simple LED display and a pinch-trigger manual override make this time-delayed brake controller easy to read and easy to use. Installation is quick and simple with no mounting restrictions. Activates brakes with a preset intensity. Install your Curt electric trailer brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in port beneath your vehicle's dash.by: John 04/13/2024
Installed but not used with a trailer yet, easy instruction and appreciate the extra hardware for the installation.
Compact and not intrusive. Decided to use the adhesive tape included and taped under the dashboard L of the steering wheel.
by: Garth 02/23/2024
1997 Ford F-350 Super Duty
They are the best at what they do. They found the parts I needed and got them to me the next day. I appreciate the dedication to their customers. This product worked for my 1997 Ford F350 with the factory-installed tow package.
by: Jason 02/23/2024
Slimmer than most of the others. Easy install with the additional pigtail.
by: Eric P. Foxboro,MA07/16/2017
Everything was as described. Easy easy installation in 10 minutes. Not the top of the line controller but it's all I need. Very fast shipping as well. Couldn't be more happy with etrailer. I will be purchasing my fifth through etrailer soon!
by: Dave K / NHS08/28/2017
Great job came on time. Installed easily. Works great. Better still is the service from etrailer. New what I needed for my truck. Deserves repeat business
by: Nicholas06/27/2018
Plugged right in to my expeditions factory plug quick easy install.
by: Diego 02/11/2023
Ford F-250 Super Duty
PERFECT. The etrailer.com employee (Roger R) that assisted me on my phone in order was fast, and efficient. He looked up my truck (2004 f250 diesel 4x4), and assisted me in ordering the exactly correct harness for my application. Plug and play. Thanks.
by: Matthew L.07/12/2017
Ford
Installation pics on my Ford F-150
by: Lawrence 02/07/2024
straight forward install, works as inte nded.
by: mike R.07/29/2013
Excellent. Perfect fit, exactly what was needed. Connected the Curt C51110 Brake control to factory wiring. Only thing that could make it better is if it came with someone to plug it in for me and save me 10 seconds.
by: Stuart 03/27/2024
Exactly what I ordered and expected.
by: Thomas 02/12/2024
Worked perfectly
by: Adam 02/09/2024
Wonderful product as well as wonderful customer service
by: Paul 02/26/2024
Delivered early. Was just what I wanted.
by: Gene 08/14/2023
Almost plug-n-go.The hardest part was where to put the controller !
by: Joe04/13/2021
We purchased our new Ford Explorer with the towing package but the dealership said it didn't come with a trailer brake controller and nothing was made for our SUV so we would have to get an aftermarket controller and have them run the wiring. After looking online I found a video on etrailer.com and it was just as easy as the video to install, the hardest part was finding the Ford plug under the dash, very happy with this product and ready to haul our RV everywhere.
by: Jay 05/10/2020
2017 Land Rover Evoque
Made installation in a Land Rover Discovery Sport a breeze! Note: This option isn’t listed on either Curt or eTrailer, but it is absolutely an option if you have the factory installed OEM trailer tow package. Your factory tow package must be dealer activated in your vehicle’s software to use the quick connect harness shown here.
Total plug and play. Zero cutting, splicing or tapping required! Fantastic.
TIP: Select your model year and Land Rover Evoque (Shares the same chassis and tow electrics as the Discovery Sport) if you want the right part numbers for your quick connect options.
by: Chris 11/09/2023
Works great in my 2000 f250
by: Nicholas08/01/2019
Made installation a snap. Just mount the break controller, plug one end into the vehicle's factory plug and the other end into the break controller.
Nicholas
8/3/2020
Still working great
by: RMT05/20/2014
2003 Ford F-150
Plugged right in to my 2003 Ford F-150, and other end into the Curt Venturer brake controller. Worked great.
Rmt
5/20/2015
so far so good. no issues.
by: ZY11/11/2021
Nice trailer brake. Works as it should.
by: SAS Ltd12/23/2022
Haven’t had a chance to install it yet but fast shipping
by: Kelly11/08/2016
2004 Ford F-150
This is well worth the money. The cord ends appear to be high quality and fit the wiring connectors on the truck and brake controller perfectly. It makes hooking up your new Curt brake controller as easy as plugging in a cord. The only way to make this any easier is to have someone do it for you. The hardest part of the whole installation was finding the factory connector to plug this cord into. Hint: On my 2004 Ford F150, the brake controller connector was just above the factory diagnostic port underneath the dash.
by: JB from MT10/09/2014
2010 Ford Expedition
This cable made the job very easy. took 10 minutes to plug in and mount with Curt Venturer Brake Controller. Very inexpensive solution. This is an old vehicle (2001 Expedition) and didn't want to put a lot of money into a brake controller setup. These parts and directions from the website made it quick, easy and inexpensive. I have not towed with the controller yet.
25
276
Show More Reviews Ask the Experts about this Trailer Brake Controller
Do you have a question about this Trailer Brake Controller?
- Can Curt Venturer Brake Controller Install in 1998 Jeep Grand Cherokee
- Yes, the Curt Venturer part # C74VV can be used on your 1998 Jeep Grand Cherokee with a factory 7-way.
Next, for a wiring kit to install the brake controller to the 7-way you would want the Wiring Kit for 2 and 4 Brake Electric Brake Controllers # 5506. This will provide the power source and ground for the wiring for the brake controller. You will need to test the wires from the brake pedal switch of your vehicle to find a circuit that has voltage when the brakes are applied and none
view full answer... - Troubleshooting Trailer Brakes Causing Harsh Whiplash Feel When Stopping For a Red Light
- There could be a few different things going on in this case Debbie. If you can tell me what tow vehicle, trailer and brake controller you have I will be able to better identify what you may have going on.
Most often this is associated with using a timed style brake controller like the Curt Venturer # C74VV. Often times these are selected because of the price but they use a set figure of brake signal to send to the trailer so no matter if you slam on your brakes or lightly press them the
view full answer... - Adding a Curt Brake Controller to a 1994 Ford Van
- If your 1994 Ford E-350 van came with a factory installed 7-Way trailer connector then all you will need is the brake controller and the proper wiring harness. For Curt brake controllers the wiring harness is # C51322.
If the van came with a factory 4-Way then you will still use the same harness but the brake (blue) wire will need to be manually run from the brake controller back to the plug in the rear instead of going through the harness where it plugs into the vehicle.
The brake
view full answer... - How Does a Brake Controller Wire to a Motorhome
- Sounds like your trailer has electric brakes already and you are just looking for a way to wire up your Curt brake controller in the motorhome.
Wiring up a brake controller is pretty easy actually. It's just a matter of running 4 wires. You would want to run the white wire to the negative side of the vehicle battery, the black wire to the positive, the red wire to circuit on your brake pedal switch that sees voltage only when the brakes are applied and then the blue wire back to the
view full answer... - Troubleshooting Truck Signal Lights Not Working Correctly with Curt Brake Controller Installed
- It sounds like you have the Curt Venturer Trailer Brake Controller # C74VV installed on your truck and are having issues with the signal lights. You can certainly disconnect the controller from the vehicle (either by cutting the wires or unplugging it from the factory port depending on how your particular truck is setup) to try and rule out where the problem is coming from.
If you disconnect the controller and the truck's lights start to work like normal again then you know the problem
view full answer... - Troubleshooting Curt Venturer Trailer Brake Controller With Brakes Always Locked On
- The Curt Venturer Trailer Brake Controller # C74VV could be faulty. To find out for sure you can bench test the controller as per the instructions. I have included those below for you to reference.
Before removing it for a bench test I suggest checking the red wire that runs to the brake switch. This should only show 12v power when the brake pedal is pressed. If the brake switch is faulty this would cause the brake controller to believe it needs to send power to the blue brake wire.
view full answer... - Display on Curt Venturer Brake Controller Intermittently Displays Red Lights
- Since it's an intermittent sort of problem, I'm suspecting a loose connection somewhere. If the red dot on the LED display is lighting up, it indicates that the vehicle has lost the electrical connection to the trailer brakes. The most common cause for this is a dirty or damaged 7-way on the vehicle or the trailer. Closely examine the sockets and pins of the 7-way trailer connector, on both the trailer and the vehicle side of the equation. Look for bent pins or green/white corrosion on
view full answer... - Troubleshooting Curt Venturer Brake Controller on 2008 Nissan Xterra with No Lights
- I spoke with my contact at Curt and he said it sounds like a problem with the wiring on the trailer, probably a bad ground. His advice was to make sure the trailer side connectors are clean and free of corrosion inside and out. The main connector grounds should be attached to clean and corrosion free bare metal surfaces.
The light grounds should also be attached to clean and corrosion free bare metal surfaces. If there is anything between a light ground and the metal trailer frame or
view full answer... - Brake Controller and Install Harness Recommendation for a 2011 Toyota Tundra
- For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate amount to the trailer brakes.
To install this controller all you would need is the install harness part # 3040-P.
I attached an install video for you to check out as well.
view full answer... - Parts Needed To Install Curt Venturer Trailer Brake Controller 2023 Hyundai Santa Cruz Factory 4-Way
- You will be able to install the Curt Venturer NEXT Trailer Brake Controller # C74VV on your 2023 Hyundai Santa Cruz with the Pigtail # C77BR. As you only have a 4-way flat you will need the Curt T-Connector Vehicle Wiring Harness # C68JR to install a 7-way on the rear of your Santa Cruz. A Mounting Bracket # C67UR is needed to secure the 7-way since there is not a bumper cutout like you find on most trucks.
view full answer... - Mounting Curt Venturer NEXT Trailer Brake Controller
- Curt has started using new brackets for their brake controllers, and that is also true for the Curt Venturer NEXT Trailer Brake Controller # C74VV.
To mount this, all you have to do is put the included adhesive tape onto the included bracket and stick it wherever you like under your dash. If you'd like, you can also use the included screws with the adhesive to mount the bracket under your dash. With the bracket mounted, you'll just slide the Venturer NEXT controller into the bracket
view full answer... - Brake Controller Recommendation for a 2006 Nissan Titan for Tent Trailer
- The Curt Venturer part # C74VV would have plenty of braking power to activate the brakes on the tent trailer you are purchasing. This controller can activate up to 3 brake axles so it would be more than powerful enough.
I do have a better option for you though. The controller you referenced is a time-delayed controller. Which means that it applies a preset amount of braking power at a preset speed every time you touch the brakes. That can work out decently, but in reality rarely do people
view full answer... - Troubleshooting Brake Controller that Says Not Connected to Trailer
- Since your trailer's brakes worked on another truck that would indicate that the problem is on the truck side of the equation. First and easiest thing to check is to check for corrosion on your truck's 7-way. Some fine grit sandpaper can easily remove any corrosion that would prevent the connetion from being made.
Testing the brake controller is fairly easy. Sever the blue brake output wire near the brake controller leaving enough room to reconnect it and then apply the manual slide.
view full answer... - Brake Controller Recommendation for a 2005 Ford Excursion V10
- Yes, the Curt Brake Controller part # C74VV that you referenced has been confirmed to fit your 2005 Ford Excursion. All you need to install it is the correct harness, part # C51322.
This adapter plugs into the port on your vehicle's built-in brake control wiring harness. This harness should be located beneath the dash, near the center console.
view full answer... - Will Display Light of Curt Venturer Drain Vehicle Battery
- The LED light of the Curt Venturer Trailer Brake Controller # C74VV draws such a miniscule amount of amperage that it would take a very long time to deplete a car battery to the point it wouldn't start the vehicle. Basically the battery would have gone dead due to inactivity before the display light would drain it.
view full answer... - Where Does a Curt Venturer Brake Controller Plug In on a 2016 Ram 1500
- In order to install the Curt Venturer brake controller # C74VV on your 2016 Ram 1500 you will need wiring harness # C51458. It plugs into the factory plug on the truck located under the dash, to the right of the steering column, taped to another harness.
I included a picture showing the location. the picture is from the instructions for # C51458 which I have also linked for you.
view full answer... - Is Anything Else Needed to Install Curt Venturer Brake Controller on a 2005 Dodge Dakota
- If your 2005 Dodge Dakota has the factory 7-Way then you need the Custom Wiring Adapter # C51332 to install the Curt Venturer # C74VV. Sure you can hardwire it but this gives you a great way to easily connect and disconnect the controller without having to install it permanently.
Same thing if you don't have the factory 7-Way. You will need the Universal Adapter # C51515 to avoid splicing the controller directly into your vehicle wiring. This adapter does require splicing but the end
view full answer... - How to Install a Trailer Brake Controller on a 2010 Chevy Avalanche
- The wiring to install a trailer brake controller is located under the dash of your 2010 Chevy Avalanche. There will be 4 or 5 wires held together with a white tag that lists the functions of the wires. The bundle should be under the dash to the left of the steering column.
If using Curt brake controller # C74VV you will also need wiring harness # C51515. The connections should be as follows:
Brake controller white to truck white for ground
Brake controller black to truck red/black
view full answer... - Wiring Diagram/Colors for Installing Curt Venturer Brake Controller
- The Curt Venturer part # C74VV uses the standard brake controller wiring colors of white for ground, red for stoplight switch, blue for brake output to trailer connector, and black to 12 volt power.
I also attached a link to the install instructions for this controller for you to check out as well.
view full answer... - Low Brake Output Power on Truck 7-Way with Brake Controller Installed and Engine Off
- The dim light on your tester is indicating a small amount of power coming from the brake output pin of your 7-Way. This is completely normal with a trailer brake controller installed like your Curt Venturer # C74VV. Trailer brake controllers will constantly send back small, short pulses of power back to the 7-Way and it's basically the controller's way of checking for a connection with a trailer.
The amount of power it uses for this is extremely small so you don't have to worry about
view full answer... - Will Brake Controller Plug-In Adapter C51322 Fit 2004 Ford Expedition And 2004 Ford E-350
- The Curt Custom Wiring Adapter, part # C51322 is designed to work with the # C74VV brake controller and will fit both of your vehicles if there is a factory trailer connector installed on the vehicle.
If you have a 4-way connector on either vehicle then you will also need part # 37185.
If your E-350 does not have a trailer connector you will first need to install a 4-way connector like part # 18252. You will then need part # ETBC7 to get a 7-way at the back of your vehicle. If there
view full answer... - Is The Curt Wiring Adapter Compatible w/ Hayes Energize III Trailer Brake Controller For 1996 F-350?
- The Curt Wiring Adapter # C51322 is compatible with the Hayes Energize III+ Trailer Brake Controller # HA81742B. Both the Curt and Hayes Adapters # HA81783-HBC utilize the same connectors allowing you to use it on your 1996 Ford F-350.
view full answer... - Brake Controller Wiring Harness for a Curt Brake Controller on a 2014 Ram 1500
- If you are using a Curt trailer brake controller then for your 2014 Ram 1500 you will need harness # C51453. Harness # C51322 fits Ford, Land Rover, Lincoln, and Mercury vehicles. The new Rams have a unique multiplex wiring system called Powernet. Because of this new design it requires a special brake controller harness, # C51453, which will allow the Curt brake controller to function properly.
view full answer... - Where is Install Connector on 2014 Ford Explorer for Curt Brake Controller
- The correct install harness for a Curt brake controller in a 2014 Ford Explorer is the part # C51322. The harness you are looking for on your vehicle will be under the dash to the center towards the center console.
I attached an install video that shows a different brand controller and harness installed in a 2013 Ford Explorer which will be the exact same process. Around the 10 minute mark is where the connector on the vehicle is found.
view full answer... - Wiring Harness For Curt Brake Controller on 2002 Ford F-350 Super Duty
- Yes the wiring harness for your 2002 Ford F-350 Super Duty is indeed the same Curt brake controllers.
The Curt brake controllers for your truck will use the Curt Wiring Adapter # C51322.
view full answer... - Recommended Curt Wiring Harness for Brake Controller on 2003 Ford Explorer
- To make your Curt Venturer Brake Controller # C74VV able to function with your factory tow package you simply need the wiring adapter harness. For your 2003 Ford Explorer Eddie Bauer edition, that wiring adapter is the Curt Custom Wiring Adapter for Trailer Brake Controllers # C51322. On an Explorer that harness is behind the glove box on the passenger's side.
view full answer... - Parts Needed to Install a Brake Controller in a 1994 Ford Bronco
- Yes, to install a Curt brake controller like the TriFlex part # C24VV in your 1994 Ford Bronco all you would need is the correct brake controller install harness part # C51322 that you referenced.
Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in port beneath your vehicle's dash.
view full answer... - Does Curt Brake Controller Install Harness # C51322 Fit 2007 Ford F-150
- The Curt brake controller install harness part # C51322 that you referenced is a confirmed fit for your 2007 Ford F-150.This adapter plugs into the port on your vehicle's built-in brake control wiring harness. For most applications, this harness is located beneath the dash, near the center console.
Most likely the mechanic you brought it to didn't know where to connect it.
This would work well with the proportional Triflex part # C24VV.
view full answer... - Does Curt Brake Controller Install Harness # C51322 Fit 2000 Ford F-53
- Yes, for your 2000 Ford F-53 RV chassis the Curt brake controller install harness part # C51322 is a confirmed fit and would work well.
It would work really well with the Triflex part # C24VV.
view full answer... - Brake Controller Installed on 2001 Ford Van Causes Turn Signal to Malfunction
- You are using the factory pigtail provided when you purchased the vehicle, not the # C51322, is that correct? If this is the case, the factory pigtail uses a different wire color code than the aftermarket ones, which match up color for color. Before proceeding further, lets make sure you have the pigtail wired correctly to the brake controller. An incorrectly wired harness or pigtail could cause the problem you describe.
Over the years, Ford has made two different factory pigtails, one
view full answer... - Where is the Wiring Harness for a Curt Custom Wiring Adapter # C51322 on a 1996 Ford F-150?
- According to the instructional manual of the Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In # C51322, the harness on your 1996 Ford F-150 is located underneath the dashboard near the center console. I went ahead and attached a photo to this answer that I highlighted that shows the location.
view full answer... - Where is the Brake Controller Installation Plug on a 2000 Ford F-250
- The plug you're looking for on your 2000 Ford F-250 is likely located behind some of the wire looms or possibly even tucked away in a nook off to the side when you remove the dash panel, but it will be there somewhere. Once you find this plug you'll be able to use the Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In # C51322 to install the Curt Tri-Flex # C74VV. I've linked a few installation videos of brake controllers that use a brake controller adapter plug so
view full answer... - Wiring Harness for 2013 Thor Challenger With Curt Brake Controller
- For a Curt brake controller, the correct brake controller wiring harness for your 2013 Thor Challenger is the Curt Wiring Adapter # C51322.
view full answer... - Can Curt Brake Controller Install on 2009 Porsche Cayenne
- For the 2009 Porsche Cayenne you can install a Curt brake controller like the part # C24VV but due to the complex wiring of your vehicle we don't have a specific fit harness for it. I attached a tech bulleting below that details everything that's needed to install a controller as well as a fitguide list for all the controllers that fit your vehicle.
If you had ran your vehicle through our fitguide you'd seen the list of controller and how they need to install. If you searched for brake
view full answer... - Economically Priced Proportional Brake Controller Recommendation for a 2004 Ford F-150
- For a great brake controller at a great price I would recommend the Curt Triflex Brake Controller part # C24VV. This is a proportional brake controller that will sense how much braking power the tow vehicle is applying and will proportionately apply the trailer brakes to slow the trailer down in a smooth, effective manner.
To install the brake controller all you need is the correct install harness which would be the part # C51322. Check out the link to the install video I attached as well.
view full answer... - Curt Brake Controller and Wiring Adapter for 2015 Forest River FR3 30DS on Ford F-53 Chassis
- To use the Curt Assure Brake Controller # C49UR with your 2015 Forest River FR3 30DS, which was built on a Ford F-53 chassis, you will need the Wiring Adapter # C51322.
The other part you will need is Adapter # 37185 to give you 7-way on your motorhome.
view full answer... - Brake Controller and Install Harness for a 2013 Ford Explorer
- For installing the Tri-Flex brake controller part # C24VV in a 2013 Ford Explorer the correct install harness is the part # C51322.
I confirmed this with Curt as a fit for your vehicle. he Ford Explorer and Mercury Mountaineer have 6-pin connectors behind the glove box on the passenger's side that this connector will install into.
view full answer...
Info for these parts were:
Edited by:
Leah B
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Jeffrey L
Written by:
Lindsey S
Video by:
Joshua S
Video by:
Jonathan Y
Video Edited:
Chris R
Updated by:
Wilson B
Updated by:
Kristina F
Updated by:
Isabelle B
Test Fit:
Ryan G
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Mike R.
1/28/2015
The products worked great up until about a few weeks ago Thats when I sold the truck where the items were installed. lol. Really though, I very much liked how the products listed and purchased from etrailer.com were easy to find, fit exactly as described, and performed as needed. etrailer.com is always one of the first places I look when searching for items for my new truck.