Camper Jacks Specs:
Features:
Improve the stability of your parked and leveled RV with these base pads. 7" Tall pads fit under smaller units as well as units with a higher clearance. Stack 2 pads to get 12-3/8" of height and a 3,500-lb load capacity.
More Information >Videos
for RV Jack Pads
Help Articles
for RV Jack Pads
Expert Answers
for RV Jack Pads
I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.
view full answer...Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side.…
view full answer...Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to…
view full answer...While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular…
view full answer...We do offer a few kayak carriers that you can use with the Thule TracRac TracONE Truck Bed Ladder Rack. You will need to use a channel mount carrier. Since the crossbars on the TracOne are a bit oversized, none of the clamp on carriers we sell will…
view full answer...The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…
view full answer...The closest compatible option for your Dometic DOTR12CB RV microwave's size is the Furrion Standard RV Microwave #FMSN09BL. It measures 19-1/16" W x 13-5/8" H x 15-7/8" D with a 0.9 cu ft capacity.
view full answer...If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
view full answer...Yes, you are correct. In order to correctly take this measurement you will need to measure from the center of the spindle to the center of the main axle tube. I have included a picture for reference.
view full answer...I agree, the bag for the NOCO Boost X Jump Starter #NOC88VR is a nice way to keep everything together but it definitely lacks in the protective department. To keep your Boost X Jump Starter safer you'll want to pick up the EVA Protection…
view full answer...The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to…
view full answer...If your trailer has separate turn signals from the brake lights and you want them to remain that way, you will need to use a special converter. On the trailer side, behind the 7-Way, you will attach the Vehicle to Vehicle Taillight Converter,…
view full answer...Filter Products (2)
Contact and Help
What our customers are saying:
In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!
Randy
Watkinsville, GA