RV Jack Pads Specs:
Features:
Designed for travel trailers with Lippert Level Up jacks with 5-3/4" to 6" square jack feet. Sturdy rubber pads install on your jacks, eliminating the need to crawl under your rig during leveling. Includes 4 pads.
More Information >RV Jack Pads Specs:
Features:
Designed for Class C motorhomes and travel trailers, these sturdy rubber pads install on your jacks, eliminating the need to crawl under your rig during leveling. Large surface area provides added stability on soft ground. Includes 4 pads.
More Information >RV Jack Pads Specs:
Features:
Increase the surface area of your camper's leveling jack foot to help prevent sinking and to get added stability. Durable rubber pad easily and permanently snaps into place.
More Information >RV Jack Pads Specs:
Features:
Replaces 1 pad for your SnapPad XTRA Square 6 jack pad system. Pad increases the surface area of the jack foot to help prevent sinking and provides added stability. Fits jacks with a 5-3/4" to 6" square jack foot.
More Information >Camper Jacks Specs:
Features:
Improve the stability of your parked and leveled RV with these base pads. 7" Tall pads fit under smaller units as well as units with a higher clearance. Stack 2 pads to get 12-3/8" of height and a 3,500-lb load capacity.
More Information >Videos
for RV Jack Pads
Help Articles
for RV Jack Pads
Expert Answers
for RV Jack Pads
If you have 10" octagonal or concave round jack feet on your Baystar, then the SnapPad EQ Octagon Jack Pads for Equalizer Leveling System w 10" Octagon Jack Feet #SN76FR will work great. If not,…
view full answer...I went out to our warehouse and test fit some SnapPads on the feet of the Lippert High-Speed Power Stabilizer Jack #LC298707 and found that the 6" square SnapPads were a fit. If your 2022 Forest River Vibe travel trailer…
view full answer...SnapPads like the SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 9" Round Jack Feet - Qty 6 Item #SP54FR6 can be taken off and on as needed so you won't have to keep replacing them every time…
view full answer...You are correct that the kit part number 70161 that you mentioned from SnapPad is our #SP24FR4 so this would be the kit you'd need.
view full answer...If you have the Gooseneck versions of the Curt CrossWing ( #C92DR or #C32DR) you unfortunately would not be able to use the Rota-Flex with it. The pivoting head causing too much strain for the single point of contact you have with a gooseneck…
view full answer...Hello John. The #C96JR tail light kit for the 2023 Jeep Gladiator will indeed work with a Brake Buddy brake System Such as part #HM39524. So, if you plan to use a portable brake system, that is definitely what I recommend, and you do not need to…
view full answer...Hey TJ, I went out and opened up one of the Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System #LC324269 boxes and found that they include a 5/8-18 x 1-1/2" fine thread grade five bolt. I then called…
view full answer...Personally I prefer the SnapPad XTRA Jack Pads #SP54FR4 over the Stromberg Carlson #SC99MR as they have been around much longer and proven themselves to be a quality product. Both these will fit 4 jacks with a 9" round landing…
view full answer...Kenny, those bolts for the B&W Companion 5th Wheel Trailer Hitch #BWRVK3500-5W should be torqued to 40 ft. lbs. Also, the pivot arms would need to be torqued to 80 ft. lbs, the draw down bolt should be tighten to 60 ft.lbs and…
view full answer...You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you…
view full answer...There's unfortunately not a guide to tell us the sizing of your trailer's jack pads so you'll want to measure and note the shape of each pad. I've run into numerous…
view full answer...The replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System - Qty 1 #LC324269 needs to be torqued to 132 ft-lb and Lippert recommends using some Loctite Threadlocker 262 - High Strength - Up to 3/4" Nuts/Bolts…
view full answer...