The assembly for the Curt Roof Mounted Cargo Basket #C18115-117 is pretty minimal. It will show up in three sections that you will insert into each other and then use included hardware to secure together. The picture I attached shows all of the…
The external measurements of the Thule Canyon roof rack #TH859XT are 50-1/4 inches long by 41 inches wide by 6 inches tall. The internal measurements are 39 inches long by 40 inches wide by 5 inches tall. The usable interior dimensions are 39 inches…
Welcome back Joshua! The Curt Roof Mounted Cargo Basket item #C18115-117 weighs 42-1/2 lbs. It has a 150 lbs capacity and measures 64-1/2" Long x 37" Wide x 4" Tall. The Roof Mounted Cargo Basket item #C18115-117 comes with universal…
Hey Alex, I contacted our representative at Curt about the Curt Roof Cargo Basket #C18115-117 and he informed me that the exterior dimensions for the basket measure 64-1/4 inches long, 39-1/4 inches wide, and 4-1/2 inches tall. The internal…
Yes, The Curt Roof Mounted Cargo Basket part #C18115-117 will certainly fit your 2018 Nissan Pathfinder if it has a factory or aftermarket roof rack installed with cross bars that are not over 3" wide x 1-5/8" tall. If you let me know what…
Hey Abelardo, thanks for reaching out! For the Sky One Touch roof, fitment options are much more limited than a standard hardtop Wrangler. Right now the only roof rack we have confirmed to fit your 2026 JL Rubicon X with the Sky One-Touch roof is the…
Hello Chris, You can run the Patriot off an auxiliary 12V battery, but it’s not something I’d recommend as a long-term solution. The unit is designed to pull from the Jeep battery, and the draw is actually pretty low. If your battery is going dead…
Hey Ed. The hitches for your 2023 Honda CR-V Hybrid, like our etrailer item #e98848, all block the sensor in the middle of your bumper where the 2" receiver sits. You would need to kick to the left or right of the center of your bumper to find…
Hey Jeremy, we've estimated the install time for the etrailer hitch part #e76ZV to be about 1 hour and 40 minutes for the average installer. If you're good at this type of install it might take a little less time and vice versa but it…
Hey Kit, yes the Inno Shaper 100 Roof Cargo Basket #INXA569 that you referenced does fit the Inno aero crossbars you have currently. This was designed to attach to the top channels of crossbars which yours have so it would it and work great. What are…
Thanks for reaching out, Dennis. Yes, if you purchase the Yakima LockNLoad Platform Roof Tray #Y05044 along with the Crossbar Clamps for Yakima LockNLoad Platform Rack #Y05039, you'll receive all of the hardware needed to assemble the tray and…
In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!
Randy
Watkinsville, GA
Inno Roof Basket for small capacity loads
Go compact when you just need the essentials, and choose an Inno small capacity roof basket for a tidy, low, aerodynamic profile. Instructions are clear and setup is straightforward, and it works well with a cargo bag and net on longer drives. If you're using t-track hardware, allow a little extra time to get the nuts started in tighter spots.
Installation can be easy and straightforward. Instructions have been clear and parts fit together well. If you're using T-tracks, test-fit the hardware before loading up. Hand-tighten first so you can adjust, then torque down once everything is aligned.
Use a cargo net sized to wrap around the platform and a cargo bag for weather protection. A properly fitting net helps keep the load tight. Pack heavier items low and cinch straps evenly. After loading, tug-test the net and recheck it at fuel stops.
It can be a solid, low-profile, aerodynamic option. One basket did great on a 6 hour trip with a cargo bag. Mount it securely, center the load, and keep the profile tidy to help reduce wind effects. Recheck hardware after the first few miles.
It can, but check bolt length in the T-track. One setup had bolts that were barely long enough once two washers and the nut were on, which made starting the nut take trial and error. Test-fit the hardware and consider washer stack or positioning to get proper thread engagement.
Filters
