Hey Dave, thanks for the pictures! Based on what you have and what you are looking for the Tie Down Spare Tire Mount part #TD66FR that you referenced would be a great option. This is very similar to what you have now so it would do a great job.
Hey Derek, thanks for the picture! The SeaSucker Universal Recovery Board Mount - Vacuum Mount item #SEA39XR is going to work great on your setup. These will have no problem attaching to the aluminum sides. It's not going to delaminate the…
I recommend the etrailer.com Trailer Hitch Receiver part #e98853 for the 2020 Toyota Sienna because of it's concealed cross tube design. The only portion of the hitch that is visible once installed is the receiver square which sticks through the…
I can absolutely help with choosing a trailer hitch for your 2020 Toyota Sienna that will give you the best ground clearance. There are quite a few hitch options available for your vehicle, but the models that will sit highest off the ground when…
The only bolt-on swivel jack we have that works with 6" tall trailer frames is the Trailer Valet 5X Swivel Jack and Trailer Mover part #STC-V211. The Trailer Valet has a 500 lb tongue weight capacity and works with frame rails up to 2-3/4"…
Hey Phil! For a tandem axle trailer you will want two of the Leveling Kit with Wheel Chocks for Trailers and RVs #WS28ER. You are correct, one under each tire is best. I use these on my Jayco with one under each tire to keep them off the ground and…
First we need to find out if the problem is your tow vehicle wiring or your trailer wiring. To do this use a circuit tester like part #PTW2993 to test all of the pins on your 7-way for the correct function compared to the diagram I attached. Next use…
You'll need to remove the ring terminal screws that hold the white wires of the #8880162 to the trailer but then the other connections simply plug into the female matching end on the trailer since it uses bullet connectors.
The Buyers Products 24" Fluorescent Orange Marker Kit #3371308103 are a hollow Nylon construction. They are pretty rigid/sturdy and are designed to be used on vehicles.
You could for sure. You would however want to make sure that the fender is reinforced enough to support the Markers #3371308103 so that they don't just rip the metal or plastic of the fender. I'd get some flat metal from a local home…
Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast.
John
Mankato, MN
Traction Boards for mud, sand, and snow
When wheels spin in mud, sand, or snow, traction boards slide under the tires to help you drive out—drop them under the front wheels on ice or use one at each wheel for an easier escape. Rugged and light, they store compactly and can double as a shovel while you dig to set them. Mount to t-slot crossbars, platform racks, or ladder-rack uprights with pins or brackets; these are recovery aids, not camper levelers.
They're not designed for leveling a vehicle or supporting a camper. Folded mats have hinges meant to collapse for storage, not to carry weight. For campers, use a larger footplate on stabilizer jacks to help prevent sinkage and keep things level.
Two boards can get you out, but four can make it simpler when a wheel loses grip. Start by digging to clear a path and seat the boards under the drive wheels. Ease onto the boards and work back and forth to build momentum. If a tire slips off the side, realign the boards and replant them.
Yes, they help in snow, ice, and deep mud. Dig to clear space so the boards can bite, then place them tight under the tires. Apply steady throttle and work back and forth to climb out. If you slide off a board, reset the angle and reinsert it firmly.
Use mounts that slide into crossbar or platform t-slots with pins or brackets, or drill to uprights if your rack lacks accessory slots. Some pin setups accept padlocks to help deter theft. Check your rack's slot type and spacing to match the hardware.
Filters
