Sure, I can help with that. I can see why the fitment notes are confusing. For a 2012 Toyota Tundra with the factory tow package and factory 7 way connector, you'll want a brake controller that plugs into the factory brake controller port under…
Based on my research your 2017 Airstream Basecamp travel trailer has a 4,000 lb Dexter Torflex axle; for that axle the correct lift kit is the Torflex Lift Kit - Single Axle - 2-5/8" Lift #K71-707-01. This lift kit is a fit for a #10 Torflex…
Hey Jon, yes we do have a Pace Edwards SwitchBlade that fits your 2017 Ram 3500 Mega Cab short bed with the part #311-SWD7833. Do you have tools in your truck bed you are wanting to keep protected?
In regards to the Titan Chain Screw Pin D-Shackle part #TCS10MM, the distance from the pin to the inside edge opposite of this is going to be around 2". I spoke with Titan and they informed me that the working load limit (WLL) is 880 lbs.
Hey Mike! Yes, you can run a dedicated AC-powered battery charger alongside the WFCO Auto Detect Converter #WF35AD. As long as both chargers are configured for the same battery chemistry, they'll work together without any issues. I recommend…
Thanks for the question, Chris! The Hidden Hitch by Draw-Tite Trailer Hitch Receiver #DT66GR is confirmed to fit all models of the 2022 Ford Explorer so it will definitely fit the ST-Line you're asking about. If you'll be doing any towing be…
Hey James, for the Yakima HD Overhaul rack the replacement bottom infill is the part #Y01166-LC and the top is part #Y01166. The bottom and top channels of the bars are the exact same dimensions and profile so they are interchangeable.
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
For your setup I recommend the TrackTowers for Yakima Crossbars and Platforms - Track Mount #Y52AV which includes everything you need to mount Yakima crossbars to your Retrax cover (unless you plan on using the Round or HD bars - then you'll need…
Yes, your RSI SmartCap load bars are compatible with, and will allow you to mount the Hullavator, which is the following part number: - Thule Hullavator Pro Kayak Carrier and Lift Assist #TH898 I have added a link below to a video review for you to…
There is not a general restriction from Thule that says two Hullavator Kayak Carriers #TH898 can't be used on a Thule roof rack. As long as the crossbars on your Ford Escape have the required length for two sets and a sufficient weight capacity…
Since we don't currently offer the RSI Smartcap I don't have any real technical info on it, but since you say they have t-slots you could use a system like the Rhino-Rack Roof Rack for Thule and Yakima Tracks #Y01-140B-NT. This rack attaches…
Built for those muddy moments, Erickson tow shackles make short work of freeing a stuck RV or trail rig. Expect sturdy performance, and some include a nice powder coat finish. If you're using a 2 inch receiver, double-check hitch fit and the distance from the pin hole to the front of the 2-inch square tubing so everything locks in like it should.
Yes, it can help get an RV out of the mud. Before pulling, make sure the mount seats fully in the receiver and the hitch pin is secure. If insertion is difficult, stop and verify the receiver size and the pin-to-end spacing on both parts.
They're described as well made with a nice powder coat finish and feel sturdy. Check the coating and edges before sliding it into the receiver to minimize scuffs. If the insert feels overly tight during a test fit, verify measurements rather than forcing it.
Measure from the center of your hitch pin hole to the front face of the receiver and compare to the length of the 2 inch square tubing ahead of the pin. This confirms the shackle mount will seat and the pin will line up. If the numbers are close, a snug fit can keep it from inserting fully.
They are made for 2 inch receivers, but fit can vary by hitch. Check the distance from the center of the pin hole to the front end of the 2 inch square tubing against your receiver to confirm clearance. If a 2 inch hitch feels tight or won't accept the insert fully, recheck dimensions and pin alignment before use.
Tow Shackles Parts or Accessories
Filters
