The Replacement Standard Dual Rack Repair Kit for Lippert RV In-Wall Slide-Outs - Fixed Side, #LC84FR is the left side of the slide-out as looking at it, facing it, from the outside. The float side, #LC26VR, will of course be the right side as facing…
Hey Stephen, we have the 16 foot etrailer awning part #e84QV that would work great on your car hauler. How tall is the side of the trailer? It shouldn't be a problem but the arms of this awning are 69 inches tall. We spent a lot of time on our…
Hey Jack congrats on the new Jeep! To flat tow a 2021 Jeep Wrangler Rubicon behind your 2012 Thor Hurricane 31J motorhome, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect…
Hello Andrew, good question. Basically the only difference between the composite kits and the standard (non-composite) kits is the application they are used for. Composite are used in motorhomes, the other are used on towable campers. It has to do…
Hey Jared, the pass through amp rating of the Rich Solar NOVA 3K12 3000W 12V Pure Sine Wave Inverter with Built-in Transfer Switch for RVs #RS79VR is 30 amps. What AC units do you have? This should be more than enough for that.
Hey, Skip! Happy to help get your new Jeep set up for flat towing. There is going to be a list of parts, so I'll go ahead and list them all below for ya. Blue Ox Base Plate: Part #BX1139 Blue Ox Avail Non-Binding Tow Bar: Part #BX7420 Demco…
Hey Donna, you would have to replace the entire setup as there was a refrigerant law change in January of 2025 that forced the complete systems to have to be redesigned and because of that nothing is currently backwards compatible. So what I would…
Hey John! Since you have the same number of teeth the Replacement 24 Tooth Pinion Spur Gear for Power Gear RV Slide Outs #LC86EX will likely work as a replacement. I would measure the outer diameter as well. If it matches the 1.417" measurement…
Unfortunately, I cannot tell you what wiper seal you would need for your 2004 Keystone Outback. This is not something that is known just from the RV information. It depends on your particular slide-out. The best way to determine what wiper seal you…
The Fixed Dual Rack Repair Kit #LC84FR goes on the left side of the slide as you look at the slide out from the outside of the camper. So on the drivers side it will be the front of the slide. The Floating Dual Rack Repair Kit #LC26VR is going to be…
You've got both a wiper seal and a bulb seal here with the wiper seals having a track for the bulb seal to slide onto. The Rubber Wiper Seal with Track for RV Slide Out #SR87FR you were already looking at is most likely the closest option to what…
Hey Kyle, yes the Flair-It High Pressure Hose #FL37FR does fit on the 1/2 barb fitting of the Flair-It PEXLock Female Elbow Fitting #FL44ZR that you also referenced.
Received already. Yeow! Perfect fit. Thanks for getting the kit to me so quickly.
Rich
Arlington, TX
RV Slide Out Parts Motor for Lippert In-Wall RV Slide-Out Systems
Match your slide with a direct-fit motor for Lippert In-Wall RV Slide-Out Systems. Choose 300:1 or 500:1 gear ratios to suit your setup, and verify round-round mounting since round-square versions require a new system. The 13398-C2 controller pairs with the correct 300:1 or 500:1 round-round motor.
Pick the gear ratio that matches your original motor. The 500:1 option provides more torque, but dimensions and design are the same, and it does not run stronger or last longer than a 300:1 in this system. If you're unsure, check the ratio on your motor label or your RV documentation since the motors can look identical.
Match the mounting plate style first; round-round applies to current replacements, while round-square motors are obsolete and require a new system. Verify your gear ratio is 300:1 or 500:1. Check the harness connection; some use a 6-pin connector, so compare your plug and wire count before ordering.
Installation can take time and isn't always a DIY job. Access may require removing interior trim to reach the in-wall motor. If your slide module shows a short between the controller and motor, verify the motor is the issue first. In cold weather, operation may feel a bit sluggish.
Yes, controllers can be compatible with 300:1 or 500:1 motors on round-round setups. If your setup is round-square, plan on a new system instead of a motor swap. Confirm your controller's supported gear ratios and connector style before you commit.
Filters
