It sure will Hans and congrats on the new Outback! The Redarc Tow-Pro Link Bluetooth Brake Controller item #RED57AR is going to work great with your 2026 Subaru Outback Wilderness. Since you have the factory tow package, all you'll need to do is…
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
Hey Andrew. The Redarc Tow-Pro link will indeed work just fine for your 2026 Toyota BZ, and due to it not needing a brake output wire you do not need to hook up the brake out put wire at all. You'll plug the USCAR pig tail #20147 into the Tow-Pro…
Hi Thomas! The distance from the center of the hitch pin hole to the center of the ball on the #BW77BR is 13-5/8". This is designed to fit a 2-1/2" receiver with a 10k rating for the 2" and 21k rating for the 2-5/16" ball. What…
Hey Robert! That Stromberg Carlson foot won't work but we actually do have the replacement SnapPad for your leveling system. The Replacement Pad for SnapPad Jack Stand Pad System - 9" Round Jack Foot #SP54FR is what you need. It works with…
Hi Tracy, The etrailer Replacement Fabric for etrailer Slide-Out Topper part #e65QV is 96" wide (8ft) and 48" (4ft) deep. It will work with etrailer brand and Solera slide out toppers. The replacement fabric is also packaged with poly cord.…
Good question, Aaron. Since your main detail is the GM MultiPro tailgate, I’d be careful here. The B&W Tow & Stow for 2-1/2" receivers #BWTS20066BMP is specifically listed as compatible with the GM MultiPro tailgate, so if tailgate…
Hey Christian, Yes, the TorkLift Tie Downs - Custom Frame Mount - Front and Rear #TL29DR will fit your 2016 Ram 2500 Crew Cab with running boards as long as you have a factory hitch receiver or no receiver at all. If your 2016 Ram 2500 Crew Cab with…
Hey Chris! The etrailer Trailer Hitch Pin and Clip #e45TR doesn't have an actual rating. This is designed to work with accessories up to Class V and in general it can handle whatever your hitch can. That being said, it looks like the AirSafe…
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
Hello again Jim, Thanks for writing in! You're looking at the correct seal. The GS-1719 DL and TRP markings are the important identifiers, and they match the Double Lip Grease Seal #58846 (or for 2 pack #RG06-050). The additional numbers, such as…
Hey Scott! Yes, there is an option that will work with your 20" spare. The Draw-Tite Trailer Hitch Receiver #DT45508 does not have the same spare tire size restriction as the Curt. This is also a Class V hitch with a 2-1/2" receiver and a…
Count on RV Designer hitch pins and clips for a straightforward, secure connection. When the span from the clip hole to the start of the bend measures a little over 3", it fits 1-1/4" AND 2" receivers. Measure the span to confirm the fit you need.
Go by the span measurement. The RV Designer 1/2" pin measures a little over 3" from the clip hole to the edge of the straight part, just where it starts to bend. That span supports 1-1/4" AND 2" receivers. Measure your receiver wall thickness and pin hole position to ensure the clip will seat.
The span is a little over 3" from the clip hole to the edge of the straight part, just where it starts to bend. Use this to verify it will pass through the receiver tube and clear the outside wall. If a spec calls out a different receiver size, confirm with this span measurement.
Measure from the outside of the receiver wall to the center of the pin hole and compare to a span a little over 3" from the clip hole to where the pin starts to bend. This helps confirm the clip will install without binding. If the listed receiver size looks off, rely on this span check.
Yes, the RV Designer 1/2" hitch pin works for 1-1/4" AND 2" receivers. Check that the span is a little over 3" from the clip hole to the edge of the straight part, just where it starts to bend. Measure your hitch from the outside of the receiver wall to the far side of the pin hole to confirm clearance.
Fits 1-1/4 and 2 Inch Hitch
Hitch Pins and Clips Parts or Accessories
Filters
