Bumper Specs:
Features:
Replace your vehicle's rear bumper with this sturdy steel recovery bumper that's designed to take off-road abuse. Welded shackle mounts come with D-rings installed. Mount 4" round lights (sold separately) in the built-in receptacles.
Installation Notes:
Drilling may be required for installation
More Information >Bumper Specs:
Features:
Get maximum off-road functionality and front-end protection with this bumper that has a built-in, tubular grille guard. Tapered ends provide clearance for approach and departure angles. Included D-rings let you perform recovery operations.
Installation Notes:
No drilling required for installation
More Information >Bumper Specs:
Features:
Replace your vehicle's rear bumper with this sturdy steel recovery bumper. The integrated, swing-away spare tire carrier can hold up to a 37" tire. Welded shackle mounts come with D-rings installed. Designed to take off-road abuse.
Installation Notes:
Drilling may be required for installation
More Information >Bumper Specs:
Features:
Get superior off-road functionality and front-end protection with this bumper that has a built-in grille guard. The "stubby" design provides maximum clearance for approach and departure angles. D-rings let you perform recovery operations.
Installation Notes:
No drilling required for installation
More Information >Bumper Specs:
Features:
Replace your vehicle's rear bumper with this sturdy steel recovery bumper that's designed to take off-road abuse. Welded shackle mounts come with D-rings installed. Mount 4" round lights (sold separately) in the built-in receptacles.
Installation Notes:
Drilling may be required for installation
More Information >Bumper Specs:
Features:
Replace your vehicle's rear bumper with this sturdy steel recovery bumper. The integrated, swing-away spare tire carrier can hold up to a 37" tire. Welded shackle mounts come with D-rings installed. Designed to take off-road abuse.
Installation Notes:
Drilling may be required for installation
More Information >Videos
for Bumper
Help Articles
for Bumper
Expert Answers
for Bumper
Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…
view full answer...The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.
view full answer...I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for…
view full answer...The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.
view full answer...We do have a compatible grease seal for your 168255TC oil seal, however, we do not carry rubber coated seals in this size. The 168255TC oil seal was designed to work with oil bath hubs on a 3,500 lb axle. For the most part, axle manufacturers have…
view full answer...To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…
view full answer...The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…
view full answer...As it seems you already know, when installing a trailer brake controller on your 2007 GMC Yukon you will need to locate the two wires under the hood that need to be connected to fully activate the vehicle's tow package. One is the power wire to…
view full answer...Basically, a free backing brake assembly like #T4423400, will have one shoe that is shorter than the other and the bracket will be a different shape. On a regular assembly, the shoes will by mirror images of each other. Also, on a free backing…
view full answer...A #93 incandescent bulb has a single contact bayonet base, and there are a couple of options for LED bulbs that will replace these. You can choose a bulb that gives off either a warm or cool light; I have added a photo showing the difference between…
view full answer...To replace your WFCO WF-8750P power center I recommend the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K. This 2-in-1 AC/DC distribution panel and converter charger keeps your power systems easily…
view full answer...Having the extra amperage of the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K has no down side. You'd at worst just have more power available than you'd need.
view full answer...