Truck Bed Mats Specs:
Features:
Add a little extra padding and protection to your truck's tailgate with this durable thermoplastic liner. The flexible, UV-resistant material won't fade in the sun or crack and break in the cold.
More Information >Truck Bed Mats Specs:
Features:
Add a little extra padding and protection to your truck's tailgate with this durable thermoplastic liner. The flexible, UV-resistant material won't fade in the sun or crack and break in the cold.
More Information >Truck Bed Mats Specs:
Features:
Add a little extra padding and protection to your truck's tailgate with this durable thermoplastic liner. The flexible, UV-resistant material won't fade in the sun or crack and break in the cold.
More Information >Truck Bed Mats Specs:
Features:
...absorb impacts and allow air circulation Rubberized thermoplastic material is flexible and durable Won't break down in extreme weather environments and is recyclable Resists harsh UV rays to prev...
Tech Tip:
Designated trim in 2 front wall locations required for mandatory retention use.
More Information >Truck Bed Mats Specs:
Features:
...absorb impacts and allow air circulation Rubberized thermoplastic material is flexible and durable Won't break down in extreme weather environments and is recyclable Resists harsh UV rays to prev...
Tech Tip:
Designated trim in 2 front wall locations required for mandatory retention use.
More Information >Truck Bed Mats Specs:
Features:
...coverage for absolute protection Made in the USA Specs: Thickness: 1/16" 3-Year warranty Keep your truck bed free of dents and dings with the WeatherTech TechLiner. This rugged, durable liner is ...
Installation Notes:
This product is intended to fit vehicles without the Pro Power Onboard Generator
More Information >Videos
for Truck Bed Mats
Help Articles
for Truck Bed Mats
Expert Answers
for Truck Bed Mats
I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine,…
view full answer...To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…
view full answer...The hub/drum you sent in a picture of is a Lippert 8,000 lb axle hub with an 8 on 6-1/2 inch bolt pattern designed for oil-bath applications. The correct replacement then is the #8-285-10UC3-A.
view full answer...Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help…
view full answer...The serial number and VIN are typically printed on a label or plate placed somewhere on the trailer's pole tongue, although it could possibly found elsewhere on the trailer frame, possibly on the inside edge of…
view full answer...The Rear Hanger for 2-1/2" Wide Slipper Springs - 6" Tall #093026 you were looking at has a hole just to allow you to measure the height of the hanger, and the hole lines up…
view full answer...It sounds like you are on the right track for tracking down where the issue is. That said, the integrated brake controllers they were putting in trucks around 2008 weren't as reliable as the ones…
view full answer...I reached out to my contact at Lippert and they said that it sounds like you just aren't holding the 4 buttons for the reset long enough. It requires 5 seconds, but many people will count to 5 a little too fast…
view full answer...It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will allow…
view full answer...The Torklift Hitch Extension part #TLE1636 that you referenced can tow a trailer that weighs 6,700 lbs like you what you have but you would need to use a weight distribution system with it to have the needed capacity as without a WD system…
view full answer...The 1-7/8 inch width is what is rounded up to 2 inches which is a standard width for winch straps. The 14 foot length is not something we carry. I recommend the Hand Winch Strap with Safety Hook, 2" Wide x…
view full answer...I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…
view full answer...