Truck Bed Mats Specs:
Features:
...if you prefer a drill-free installation Snap installation allows you to easily remove and reinstall for cleaning Made in the USA Specs: Application: bare truck beds or those with spray-in liners or drop-in...
More Information >Truck Bed Mats Specs:
Features:
...if you prefer a drill-free installation Snap installation allows you to easily remove and reinstall for cleaning Made in the USA Specs: Application: bare truck beds or those with spray-in liners or drop-in...
More Information >Truck Bed Mats Specs:
Features:
...Optional tailgate mat available (BMB15TG - sold separately) Made in the USA Specs: Application: truck beds with drop-in liners Will not fit trucks with bare beds or existing spray-in liners Does not cover...
More Information >Truck Bed Mats Specs:
Features:
...Optional tailgate mat available (BMB15TG - sold separately) Made in the USA Specs: Application: truck beds with drop-in liners Will not fit trucks with bare beds or existing spray-in liners Does not cover...
More Information >Videos
for Truck Bed Mats
Help Articles
for Truck Bed Mats
Expert Answers
for Truck Bed Mats
The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a…
view full answer...To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…
view full answer...Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article…
view full answer...The serial number and VIN are typically printed on a label or plate placed somewhere on the trailer's pole tongue, although it could possibly found elsewhere on the trailer frame, possibly on the inside edge…
view full answer...The Rear Hanger for 2-1/2" Wide Slipper Springs - 6" Tall #093026 you were looking at has a hole just to allow you to measure the height of the hanger, and the hole lines up…
view full answer...It sounds like you are on the right track for tracking down where the issue is. That said, the integrated brake controllers they were putting in trucks around 2008 weren't as reliable as the ones…
view full answer...The Torklift Hitch Extension part #TLE1636 that you referenced can tow a trailer that weighs 6,700 lbs like you what you have but you would need to use a weight distribution system with it to have the needed capacity as without a WD system…
view full answer...I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire…
view full answer...It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will allow…
view full answer...I reached out to my contact at Lippert and they said that it sounds like you just aren't holding the 4 buttons for the reset long enough. It requires 5 seconds, but many people will count to 5 a little too fast…
view full answer...The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…
view full answer...I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…
view full answer...