Truck Bed Mats Specs:
Features:
Use this universal-fit, heavyweight tailgate mat with your DeeZee truck-bed mat to extend bump-and-scratch protection to your vehicle's tailgate. The thick rubber mat will not crack or break - even in extreme temperatures.
Tech Tip:
Mat may require trimming as it is a universal design for this bed size, not a custom fit.
More Information >Truck Bed Mats Specs:
Features:
Use this universal-fit, heavyweight tailgate mat with your DeeZee truck-bed mat to extend bump-and-scratch protection to your vehicle's tailgate. The thick rubber mat will not crack or break - even in extreme temperatures.
Tech Tip:
Mat may require trimming as it is a universal design for this bed size, not a custom fit.
More Information >Truck Bed Mats Specs:
Features:
Use this tailgate mat with your BedRug truck-bed floor mat to extend slip resistance and 1/4" cushioning to your vehicle's tailgate. Be good to your knees when unloading cargo or working in the back of your truck - you might need them later.
More Information >Truck Bed Mats Specs:
Features:
This bed mat protects your load and your truck bed by preventing cargo from shifting as you drive. Made of heavyweight Nyracord, the mat is extra thick and will not crack, rust, or break. Mat is custom fit for your vehicle.
More Information >Truck Bed Mats Specs:
Features:
This bed mat protects your load and your truck bed by preventing cargo from shifting as you drive. Made of heavyweight Nyracord, the mat is extra thick and will not crack, rust, or break. Mat is custom fit for your vehicle.
More Information >Videos
for Truck Bed Mats
Help Articles
for Truck Bed Mats
Expert Answers
for Truck Bed Mats
I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine,…
view full answer...The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack…
view full answer...To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…
view full answer...Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've…
view full answer...The proper replacement inner assembly member for your UFP 34043 would be indeed be the the Dexter #DX99FR which is compatible with disc brakes. The replacement has an electric lock out and has a 7500K capacity and is intended to work with a 2 inch…
view full answer...The Rear Hanger for 2-1/2" Wide Slipper Springs - 6" Tall #093026 you were looking at has a hole just to allow you to measure the height of the hanger,…
view full answer...It sounds like you are on the right track for tracking down where the issue is. That said, the integrated brake controllers they were putting in trucks around 2008 weren't as reliable as the ones…
view full answer...I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need…
view full answer...It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to…
view full answer...I reached out to my contact at Lippert and they said that it sounds like you just aren't holding the 4 buttons for the reset long enough. It requires 5 seconds, but many people will count to 5 a…
view full answer...Hey Jeff, the WeatherTech ImpactLiner Custom Truck Bed Mat #WT99KF would get secured to your bed using the TechHold Retention Device (see image attached) which is just a adhesive ball and socket. Basically, one the ball end would get stuck to the…
view full answer...I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…
view full answer...