# 1
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
I am very pleased with the hitch, ball mount, and electrical package. All were easy to install if you follow the easy to understand directions. An added plus for putting one of these on a MINI is that the hitch can be hidden behind the "black plate/cover" that is on the rear bumper. It looks just like it came out of the factory except when to need to install the ball mount. The service has been outstanding. This is the place to go.
# 2
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
Easy ordering, fair pricing, prompt delivery...product arrived in excellent condition, very heavy duty drawbar for use with by 4ft x 8ft medium duty trailer.
This drawbar was clearly used. See the picture. I asked etrailer about it and sent this picture but the person that replied, Noah, thought it must have been bumped around in shipping. If shipping caused this much damage, it's a poor quality product. If it was, in fact, used, then etrailer lied to me. Either way...not good.
# 3
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
Easy install, took around 30 minutes by my self to install. Hardest part of install was torquing the bolts ! Installed 13322 Class III Hitch - Gm 1500/2500 Pickup and Curt Class III Ballmount -2ball-2 Drop
# 4
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
I purchased the etrailer.com 2-3/4 " Rise or 4" Drop Ball Mount Kit, Curt Trailer Hitch Receiver and Twist-in 7-Pole RV-Style Trailer Connector for my 2011 Chevy Silverado. Quick Delivery! All the necessary parts arrived in perfect condition. Directions were spot on and the instructional videos were great.
The drop ball mount is the perfect size for my Jeep. The versatile hitch balls are convenient. Thank you for putting together a great kit, providing excellent communication, and delivering it quickly.
# 5
Convert-A-Ball Ball Mount for 2" Hitches - 10-3/4" Rise, 12" Drop - 7,000 lbs
Needed a large drop hitch to pull my car trailer. This item came quickly and worked perfectly.
This extreme rise ball mount is what I need to make my passenger car into a back-up trailer puller. It is well built and has a welded strut to reinforce the long rise/drop ball mount. The "shock damper" feature is sure to help absorb the leverage movement that a rise/drop ball mount passes on to the hitch receiver itself.
# 6
Curt Class II Euro Style Drawbar with 1-7/8" Ball - 6-5/8" Rise - 3,500 lbs
Great Product! After installing a Curt (C11184) Hitch on my '08 BMW 135i convertible, I needed a drawbar and ball. I really liked the elegant design and one piece simplicity that this one has. It is very sturdy and the dimension measurements were accurate. The whole reason I got it was to trailer my new (old) wood boat home from the barn I found it in. Once the hitch was on and the (56146KIT) Wiring kit was installed. This drawbar slid right in. Thanks to the accurate measurements the trailer sat at the perfect height the first time.
works great
# 7
Draw-Tite Ball Mount for 2" Hitches - 3" Rise, 4" Drop - 9-1/4" Long - 16K
Perfectly as described, Box was a heavy hitch and the box must have been damaged in shipping so it was a little delayed. You can't mess up a forged hitch it still is in excellent condition.
This simple ball mount will get the job done. It's a solid casting so it weighs a lot.
# 8
Brophy Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 13-1/4" Long - 10K
Slightly longer, so you can open your tailgate with a cargo trailer attached. Trailers with a tongue jack that is forward are problematic for tailgates...
I’m pleased with the product and how prompt the delivery was. However the packaging was insufficient and the packaging was torn open all over. Scuffing of the finish is a result and of little consequence due to the intended use. It’s a stinger w/ball for motorhome. May I suggest better packaging in the future
# 9
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
Excellent customer service & support! Bought for my 2013 Honda Fit and plan to trailer my Yamaha Tenere motorcycle around North America! Very happy with hitch.
Typical quality of...VERY good!! Lol. I've pulled my small mc trailer numerous times with this hitch and NO issues!!!
# 10
Draw-Tite Drawbar for 1-1/4" Hitches - 5" Rise - 10" Long - 3,500 lbs
This is the correct towbar for a Toyota Prius C. The towbars that are available from U-haul (3 1/8") and other hardware stores are too low to the ground for most trailers. I tow my Harley Dyna on a motorcycle trailer behind my Prius C with no problem. Save yourself the grief. I bought three readibly available tow bars until I found the right one. The 5" rise, 10" long works perfectly. This is an incredibly strong drawbar.
Worked perfectly Did have to grind off the paint and a nit of metal to fit in the reciever though.
# 11
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
What our customers are saying:
"Excellent service and communication. Expect part to be excellent too!"