# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Purchased a hidden hitch and hitch insert from etrailer. It was very easy to install. The vidios they have on line are very helpful and one person can install the hitch. I have a 2012 Nissan Rouge and I used a hydraulic jack to lift the hitch up while I maunevered it into to place. Which was very easy. The only trouble I had was taking the bolts out of the tow ring because the were in very tight. Other than that the whole process took about 30 min. The delivery was quick and the products were excellent.
The product doesn't come with a Hitch Pin. Just remember to order it. Thank you for a good shopping experience.
# 2
Curt Ball Mount for 2" Hitches - 1" Rise, 2-1/4" Drop - 7-5/8" Long - 7,500 lbs
Just your basic ball mount, the product is just like most 2” Hitch ball mounts, the service wasn’t very good though. Ordered on June 15th (product was in stock) took them 6 days to send it out, took another 6 days in shipping and got all the way to my post office two days before leaving on vacation (I needed it for the vacation) and the post office said “box was empty and they notified seller” etrailer sent a new one (got here a week after my vacation) in a damaged box (packaging is horrible, little bit of paper in a box with a 5 lbs ball mount) almost lost this one too. I don’t believe I’ll be using etrailer in the future (had issues before)
# 3
Draw Tite Drawbar for 1-1/4" Hitch - 5/8" Rise, 1-1/4" Drop - 9-3/4" Long - 3.5K
Great product at a great price!!!!
Every Item I have ordered from etrailer.com has been top of the line . Easy ordering , prompt service , and excellent installment instructions . I watch the video , more than once , and follow the expert's direction . I wouldnt order trailer parts anywhere else . Thank You
# 4
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs
I needed to tow a trailer with a 2" ball. My original ball mount has a 1 7/8" ball installed. I had previously tried to change a ball on a hitch and destroyed the nut and damaged the underside of the ball mount. The lock washer had done a great job in keeping the nut from coming off. I dreaded trying to remove my 1 7/8" ball to install a new one that I would only use once. I decided to buy a new ball mount and mount the new 2" ball. This ball mount is so inexpensive that I realized I could have both ball sizes permanently mounted for use in either ball size.
I wasn't sure what type of ball mount I needed for my new Mazda CX-9, so I had to call a representative. The first time I called, the very knowledgeable gentlemen told me exactly how to measure my SUV to figure out the drop I needed. I called back the next day and talked to a lady who helped me figure out exactly what I needed. This is my second purchase from etrailer. The first was a hitch for my old Honda Odyssey, which was also a great experience. The employees are so helpful, the video tutorials on the web site are fantastic and the prices are great. etrailer.com is the first place I go to look for trailer and towing supplies!
# 5
Curt Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-1/4" Long - 3,500 lbs
heavy duty
great product great service I bought the hitch took me 15 minutes to install it on a 2004 civic fast shipping great company thanks
# 6
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
The product is good but a bit tideous and after installing it my bracket fell and it was a pain to get replace it support made me buy the replacement pieces and the bracket didnt come with just the bolts, and at the end they told i have i had to buy the whole unit because based on their system my truck didnt have issues with installement and the manufacturer didnt supply that bracket cause it special order so in general i dont recommend in my choice better to get it welded.
Very knowledgeable group easy to work with I would always continue to use trailer :)
# 7
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
perfect
I purchased this Curt Ball mount 10-1/4" because I also bought ball hitch mounted mud flaps and my existing hitch was too short.This hitch was maybe a little too long, but it should work.I hope this combination will protect my horse trailer from my nasty gravel roads!
# 8
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
I had a great experience with etrailer.
This part came with the trailer hitch I purchased. It was very easy to transfer the ball from my 2" hitch and voila I am now ready to haul my trailer.
# 9
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.
This slightly longer than average bar was perfect for my application. The drop length was perfect also for the application. As usual, eTrailer's site and retail experience was first rate. Lots of info and specs (and videos) available makes it easier to get that piece of mind knowing that what you needed was what you ordered.
# 10
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
Good quality product that gets hitch ball/trailer coupler a few inches further away from rear bumper of new NISSAN ROGUE.
Just what I needed and arrived fast and well packed.
# 11
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Very happy with this ball mount - provides just the amount of drop we required for a level tow of our GeoPro travel trailer by our RAM2500. Plus, the extra length not only allows a tighter turning radius, but also allows us to lower the truck tailgate without having to detach the trailer. Huge improvement on all accounts for us compared to our prior setup. The product is well built and I'm confident will provide us years of good use.
Your packaging it's lousy, package arrived with a receiver size hole in the end of box . Guess what the box was empty . This is the second time I have had problems with your company !
# 12
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
For a 7,500 lb hitch, I was surprised it didn’t have a wedge support welded on where the flat iron is welded to the square tube.
Haven't used it yet. I bought it because of CURT's quality. It was beat up in shipping though.
# 13
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack. The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.
# 14
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 9-3/4" Long - 3,500 lbs
This draw bar in perfect for my John Deere X738 tractor. What I like about it is the ¾” rise it keep the draw bar height at about the same as the factory frame so the attachments height remain level. Thanks for the great product.
Well made, quality product.
# 15
Curt Class II Drawbar - 3/8" Rise, 1" Drop - 7-13/16" Long - 3,500 lbs
Excellent quality and construction. Matches perfectly with my Curt hitch. Highly recommend. Also, etrailer has the best customer service of any online retailer I've ever shopped at.
Product was excellent, complete and simple mounting instructions. Installed hitch in less than half hour. Looks great on the vehicle . Would order from E Trailer again. Thanks
# 16
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Wonderful product. I had the hitch installed in 10 minutes. The wiring was a little more tricky because it required running a power wire all the way to the battery. I towed my trailer from Florida to Tennessee and back. Etrailer is still wonderful to deal with as they always have been in the past. My hitch came in a couple of days. I wouldn't think of ordering from any one else.
# 17
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 6-3/4" Long - 3,500 lbs
Works great. Good tight fit
No issues after one year of use. Happy with product
# 18
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
Easy ordering, fair pricing, prompt delivery...product arrived in excellent condition, very heavy duty drawbar for use with by 4ft x 8ft medium duty trailer.
This drawbar was clearly used. See the picture. I asked etrailer about it and sent this picture but the person that replied, Noah, thought it must have been bumped around in shipping. If shipping caused this much damage, it's a poor quality product. If it was, in fact, used, then etrailer lied to me. Either way...not good.
# 19
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.
This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.
# 20
Curt Class II Drawbar - 3-1/8" Rise - 11-1/4" Long - 3,500 lbs
Used on my 1999 Dodge Intrepid's CURT 12006 Class II 1.25 in. Receiver Hitch: 350lbsTW/3500 lbs GTW. I use this Curt Class II Drawbar - 3-7/8" Rise - 11-1/4" Long - 3,500 lbs to tow a 3,500+ GTW dual axle trailer. I have used it with the trailer FULLY loaded and it performs EXCELLENT. You have to make sure the trailer is loaded correctly so as not to put too much down force on the tongue/drawbar. I was skeptical that the SOLID 1.25" bar would not take the load, but it is super strong. I chuck it in the trunk when not in use to protect passerby's shins, but it sticks out far enough clear the Intrepid's bumper, and is solid with a 2" ball (required a bushing). etrailer got it out fast at a good price! I would totally purchase this again from them.
Simple as a hammer. Solid steel and quite heavy duty for the intended class.
What our customers are saying:
"Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast."