# 1
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Sara R was helpful helping me find the right hitch for what I described as needing. I was excited to see the hitch pin in my order details even though I didn't order it. Sadly, the picture gave me a false impression. Overall, excellent customer service and product.
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
# 2
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
I purchased the etrailer.com 2-3/4 " Rise or 4" Drop Ball Mount Kit, Curt Trailer Hitch Receiver and Twist-in 7-Pole RV-Style Trailer Connector for my 2011 Chevy Silverado. Quick Delivery! All the necessary parts arrived in perfect condition. Directions were spot on and the instructional videos were great.
The drop ball mount is the perfect size for my Jeep. The versatile hitch balls are convenient. Thank you for putting together a great kit, providing excellent communication, and delivering it quickly.
# 3
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
# 4
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
Easy install, took around 30 minutes by my self to install. Hardest part of install was torquing the bolts ! Installed 13322 Class III Hitch - Gm 1500/2500 Pickup and Curt Class III Ballmount -2ball-2 Drop
# 5
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 6
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
Excellent customer service & support! Bought for my 2013 Honda Fit and plan to trailer my Yamaha Tenere motorcycle around North America! Very happy with hitch.
Typical quality of...VERY good!! Lol. I've pulled my small mc trailer numerous times with this hitch and NO issues!!!
# 7
Draw-Tite Drawbar for 1-1/4" Hitches - 5/8" Rise - 6-5/8" Long - 2,000 lbs
Exactly what I was looking for, received and installed and is perfect. Thanks
The hitch was well made and relatively easy to install. I installed it on a 2016 Golf Sportwagen LE. I can confirm that as others have stated that I did NOT need to trim the bumper fascia (as the instructions said I would need to). I separated the black, lower part of the fascia from the top part before reinstalling the main fascia. I was then able to snap the lower part on after fitting it around the hitch chain loops. A couple of other notes: the LE has the rear cross traffic alert. The sensors are bolted on each side of the bumper. I thought with the additional thickness of the sensors that the bolts might not be long enough but they fit fine. As has been mentioned in other reviews, the torx screws in the wheel wells have very little clearance. I highly recommend getting a torx racquet set. I bought one at a hardware store for about $20 (Kobalt 24-Piece Standard (SAE) and Metric Mechanic's Tool Set with Hard Case). This makes the removal of those screws straight-forward.
# 8
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 9-3/4" Long - 2K
This is a great product. I really appreciate the quality. This was also a car I was having difficulty finding a trailer hitch for. So thanks again for a good product.
I got a hitch for my Honda accord it was extremely easy to install took less time than they estimate after I installed it I bought a trailer and have hauled various things already with no problem I would recommend e trailer to anyone
# 9
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
Works perfectly. Fast shipping. Very Satisfied.
Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .
# 10
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 11
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 12
Curt Class I Drawbar - 5/8" Rise, 1-1/4" Drop - 9-3/4" Long - 2,000 lbs
I purchased two drawbars for my Polaris ATV. Good quality and very fast shipping from etrailer.
This is the second hitch I have purchased from etrailer and, again, it was a perfect fit. Everything I buy from here is exactly what they say it is and exactly what I was needing. I will always recommend etrailer, they have never let me down. Gene Houston Texas area.
# 13
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Purchased for a Hyundai Elantra. After a 2" ball is mounted, there is about 7.5" from the top of the square shaft to the top of the ball. This is what was needed to get the center of the ball 18" off the ground for most U-hual trailers. This design has no plate edge protruding below the square shaft. This helps reduce scraping when going over bumps, which is an annoying issue with my other ball mount. I would have much preferred the euro ball mount, which has a nice 45' bend to avoid scraping, and a ball that will never vibrate loose, but one was not offered with this much rise. The ball mount is well made of solid steel, not a hollow tube. Finish quality is excellent. The mount does not come with the locking pin needed and so that must be ordered separately with the ball. Item was packed a little loose in the box and was clanking around with the other item I bought, but they did not get scratched up.
# 14
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.
This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.
# 15
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
I bought this on my knowledgeable brother's advice - he gave me the exact order number and link to buy from etrailer! I had it installed locally, without complications. I use my truck mostly to haul my horse or my friend's two donkeys in my 14-foot stock trailer. I have no complaints, the hitch does what it's supposed to do.
Easy install, everything included, and great instructional video. Worked out great for my RAV4.
# 16
Curt Class I Drawbar - 5/8" Rise, 1-1/4" Drop - 6-3/4" Long - 2,000 lbs
I wrote 2 days ago and haen't heardafom anyone so I guess you only want reviews-. Here is what I wrote Steve, the class 1 hitch doesn’t fit the trailer hitch either. I don’t understand the continuing problem with all of the Curt hitches we have tried including the last draw hitch you selected and shipped, which I now need to return after H. Idalia passes, I want to point out that I initiially ordered somewhere on line a Maxxhaul adapter so I could move my 2” trailer until I sell it and it fit perfectly. I NEVER expected to have so much trouble getting a ball hitch to fit the 1.25 hitch recommended by etrailer for my car. Aren’t you glad I am writing an email rather than make star comments? I know that someone writes these things for ‘you’ and you don’t necessarily do the hands on so please direct this problem to someone who is supposed to make these product directives and solve this $[XX] attractive trailer hitch problem so I can haul my lawnmower in for repairs when needed on my utility trailer designed for doing so. Doesn’t Drawtite have a ball hitch for level hauling a trailer rather than Curt which is too thick. The powers that be need to rethink OD (outside diameters) vs ID (inside diameters) in their trailer connectors, screw the rattling! PS don’t forget arrangements for the return of the recommended draw hitch.
Great price! Amazingly fast service! The drawbar was a very tight fit in the hitch until I scraped off some of the paint at the end; then it was perfect.
# 17
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 2" Rise, 4" Drop - 7.5K
Nice combination to go with my front hitch for the F150.
dodge journey 2014 etrailer service excellent the hitch don't fit perfect with the spare tire other ways is pretty good if you tele out the spare tire you going to have a hard time to put them back etrailer sevicio es excelente la pieza no se acopla perfecto con la rueda de repuesto del resto se monta perfecto . si se retira la rueda de repuesto es muy dificil de poner de vuelta en el compartimento
# 18
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
My order was missing installation parts, but the etrailer team were quick to correct the issue. Even without a lift, I was able to install the receiver and brake light cable quickly, thanks to their extensive video libray.
I cannot emphasize enough how kind and thorough etrailer's customer experience team is. I originally (incorrectly) place an order for trailer parts that did not fit together, and etrailer took the time to review my order, identify the issue, call and email me to let me know, and place the correct order while over the phone. I am not an expert on any of these items so it is so unbelievably appreciated that they cared enough to check to see if I meant to order what I did. The delivery then arrive a day earlier than expected. What more could you possibly want from a customer service team? Thank you so much, etrailer!
# 19
Curt Class I Drawbar - 5" Rise - 9-9/16" Long - 2,000 lbs
For Mazda CX-3 owners, this is the drawbar you need to achieve the correct final hitchball height for small U-Haul cargo or motorcycle trailers. You know the receiver sits quite low so this gets the height just where it needs to be, especially when the trailer is properly weighted/loaded.
Shipped in quicker than I thought it would. It fit it my old Hidden Hitch Class I receiver perfectly. I drive a '97 Geo Prizm, and the 5 inch rise is a definite plus in keeping my 5 x 8 utility trailer nice and level when I'm hauling lawn equipment. The only drawback is that the Curt drawbar does not come with the pin.
# 20
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
The one foot ball mount works great on a 2014 Chevrolet Silverado work truck(no lift kit). We use it for a one axle, lawn care/utility trailer. It is used at least half the work week and has held up for a year. It may not be a good choice for a heavier trailer, but at that point we would also purchase a 2500 truck too. The mount helps clear the jack when the tailgate is opened with about 2 inches to spare.
Great product for getting out past the tire carrier on a small SUV. Customer service was wonderful with great follow through and any assistance I needed I will definitely use etrailer agin
What our customers are saying:
"Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast."