Best 2013 Freightliner M2 Accessories and Parts

I mounted mine onto a piece of aluminum flat stock on the trailer “A” frame to reduce rock impact from Nevada’s gravel back roads. There really wasn’t good location on inside of trailer frame rails, was adding electric brakes and converting from 4 pin to seven. . I’m pretty darn happy with this junction box as it made rewiring rather straight forward. Our local 12 volt guru at the auto electric shop was duly impressed-wanted to know where I found it.

Click to Enlarge

One of the best set-ups. This is definitely the way to go with your trailer wiring. The built in labeling inside aids in installation and troubleshooting. Make sure to provide some impact protection if mounting this in and exposed area.

I ordered installation bracket for Roadmaster steering stabilizer for my 72 RV I had a very hard time finding it no one had it my salesperson Chris w went out of her way to help me was extremely nice and helpful and Save the Day I will look here for any other parts I need first thank you very much I couldn't be more pleased and the part came as promised

Exactly as ordered. Brackets fit perfect

I have to start by confessing that I pulled a real dumb mistake, not taking the cord out of my RV and then not securing it when I drove for 30 miles. The small end dragged for most of that and you can see the result. Amazingly it still worked and I secured it with electrical tape for the final leg of my journey. Then I started looking at repair for the damaged end. NOTHING could compare to how the original is made. A repair would not be watertight, had the potential for crimping or wearing of the wires at the end of the new female plug, and cheaper imitations are made from lighter wire and are not watertight. I ultimately decided to buy another Blue Ox connector and will repair the old one to have as a spare. There is no substitute for the quality of this item. Bonus was that it delivered from etrailer 2 days sooner than expected!

Click to Enlarge

Much better than my old cord. This newer cord has better support where the cord goes into the plug to prevent breaking. Five stars as well to etrailer for such prompt shipping. I actually received this two days earlier than projected.

Arrived a little beat up (shipping guy said that was common with ET) due to poor packaging but it's a hitch so it doesn't affect it. Still..

I was very happy with the patience and helpfulness Lauren spent with me helping me. Very please with the knowledge she has on the products I was inquiring about and thee time spent researching and confirming which part I needed. Highly recommend for all trailer parts for knowledge, price, and speed of shipping. Once again thank you Lauren #72985

E-trailer has always been very helpful with me and making sure I get the right part in a timely manner. They are my #1 go to for my trailer parts.

Even though I gave you the correct trailer information, You guys sent the wrong equipment, I had it installed and it didn't work correctly, when I let your guys know, they wouldn't take it back because it was considered used. I lost over a $xxxx bucks??

Smooth easy transaction. Will definitely purchase for you guys again. Thank you

was sent the wrong cable initially - there are two that are VERY similar. Maybe order both? Or make sure you know which one you need.

Friendly order service & efficient.

Replaced the right-side holder with this exact Yakima assembly. Easy process, just two bolts which new ones were included. The etrailer website was very helpful, the staff had previously answered a few questions I had. The wheel holder assembly arrived in a few days and was well packed, no damages in shipment. Another very excellent transaction with etrailer.

The item looks fine. The implement would not slide into the hitch as the tolerance was too slim, not sure if it was the receiver or the implement, but I had to grind down the edges of the implement to get it to slide into the hitch.

etrailer customized the RM-048-10 by lengthening the shaft so that it would fit through the bumper of our Class C RV and be strong enough to support the Stowaway 2 Cargo Carrier. It works beautifully! During travel there is some left to right wiggle that occurs with the carrier. We solved this problem with ratchet straps to secure both sides of the carrier. The hitch is stout and strong, and does the job! Of course we strengthened it with the clamps, so the hitch is solid and unmovable. With the custom hitch, the Stowaway 2 carrier is lifted enough so that it doesn't bottom out when traveling up or down steep hills. etrailer staff are very easy to work with, along with the brilliant engineers who communicated well with the exact details of the design to assure the build worked safely. It is an excellent hitch; worth the value. We're on the road again with all of our lawn chairs/tables, etc. in the cargo carrier out of the elements, instead of inside the RV. Great work, etrailer! Thank you! S&S

Click to Enlarge

Click to Enlarge

Installed on a McClain Tandem boat trailer. Come with all necessary hoses and clamps. The hoses are made of high quality and works great. Recommend for all trailers.

Click to Enlarge

Click to Enlarge

The whole staff at etrailer bent over backwards to make sure I was satisfied with the installation of brakes on my trailer. Have made several purchases from them always satisfied with parts and service. Special credit to Jamie great to deal with. Answered all my questions and was very knowledgeable.

The combo of the Reese sway control and the weight distribution hitch is an excellent combo. I pull a 22' trailer with a 2020 Ford Ranger and I couldn't be more pleased with the performance of these combined systems.

Sorry for the long review. Purchased these as an addition to our Reese high performance weight distribution hitch. I was previously using friction sway control with our previous trailer, which was much smaller (by 10ft) and much lighter. Our new trailer is 36', 8,600lbs with a 950lb hitch weight. The tow vehicle is a 2016 F150 Lariat super crew with max tow. After towing the new trailer one time with friction sway control, I needed something else. Since we already had the hitch, I figured I'd try this instead of purchasing a new system. The dealer installed the kit as I was there for warranty work already. Towing the trailer home, the sway on the freeway was terrible. After doing a ton of research online, and various forums, I found dealers typically never put the time into setting this system up correctly, which I found is key for proper operation. I went through the complete setup with the hitch, and then the dual cam system myself (as I didn't trust the dealer who also originally set up the hitch as well). The instructions are a bit vague on setup, especially chain links from the cam to the snap up bracket under tension, which the forums helped greatly with. The dealer set this up to have 4 links under tension, when I found you need 5 at the minimum. Also found the 3/4 cam pivot nut not tightened anywhere close to 35ft/lbs. After setting this system up correctly, there is virtually no sway at freeway speeds. Moral of the story is that the setup is pretty tedious (took about 2 hrs), but once done, the system works great!

Click to Enlarge

Installed the new Brophy scissor steps and the optional hand rail yesterday on our cab over camper, we are very pleased with the wider steps, plus my wife loves the hand rail. The four step scissor steps were the perfect height from our camper to the ground which replaced a three step scissor that were narrower and had to have a support box to make them work. The new scissor step installation was very easy to do as was the hand rail. I highly recommend the Brophy scissor steps and the hand rail option, for the price, it's a great product.

Click to Enlarge

Click to Enlarge

Click to Enlarge

while I have not actually installed these(tropical storm Ophelia interrupted that process) I was disappointed in the handrail... basically it is 2 pieces of aluminum tubing a small bracket and hardware... hardly worth $[XX]

The product looked ok however I bought 15 of these for my RV and the packaging was terrible. Product came in small open plastic bag and some just floating around loose in the envelope. This product can easily be damaged better care in shipping would ensure a great product. Thanks

This is the fourth item I have ordered from etrailer. Each time I order I am reminded how easy it is to navigate the web site and the customer service is great. The sales team goes out of their way to help find a product and makes sure you are happy with the end result. I highly recommend this company for everyone ! Thank you etrailer !!!!

We have had no problems with the brake controller.

Works good so far. It would be better if it had a 90 degree bend in the cable coming out of the 9 pin plug. right now, you have to create a loop to get it installed under the dash, and this is problem on many HDT because the the 9 pin ECU plug is near the steering wheel adjustment peddle or the clutch peddle.

Was exactly what I needed, bought a couple extra, fit was perfect for the Lippert axles

Exactly what I needed. Good quality.

The items are great. A sturdier box or packaging would definitely help in not loading any items. My two items were inside but does look like the receiver shank came out through opening on side of box

Product is fine. Your packing need A LOT OF IMPROVEMENT!!! box was busted to hell and back with a 30lbs piece of metal just clanked around in an oversized box with 2 small sheets of packing paper.

product was well described which made me confident I purchased the right part the first time.

Product worked as intended

Love the fact that I can put my specific vehicle information in and it tells me everything I need to set it up as a tow vehicle behind my motorhome. Great communication all along the process from ordering to delivery. I even had to return items and very quick, efficient return response. Excellent company! Excellent customer service! Excellent products!

Click to Enlarge

We have a 45 ft RV that has this at the back and we pull our Jeep Grand Cherokee Trail hawk with our bikes on the back of the Jeep. We hook up in about 7 minutes and unhook, at our destination, in about 2 minutes. Super easy and reliable.

Click to Enlarge

Very professional easy to install. The protective covering insures the circuit breaker doesn’t get shorted out if something touches it. I used it to connect to the Deka jacketed 2 wire that ran to my 7 pole trailer plug (12 volt feed) on my rear bumper.

Click to Enlarge

This review includes the following items: Item #RED69FR - Wiring Harness, 30A Breaker kit and Item # ETBC7 Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat and Item #RED24FR Controller. I wanted to be sure I had everything. A local place Custom Coach on Pulaski Hwy, Baltimore did a fantastic job on the install, Sorry I can't remember the techs name. I have a 2018 Kia Sorento SX V6, AWD with 4 pin Tow Pkg. car rated for 5k/500# load. Trailer is a 2022 Palomino Real Lite RL-186. I've logged 2 trips so far 1 to NYS mostly highway and to Cass, West Virginia area. The controller adapted quickly, I went to a '5' to a '4' setting even in the mountains it was smooth no jerking. The one picture shows installation ubder the dash totally out of the way. It works great!

I like these. I use my trailer for cargo as well as tractor hauling. By welding banjo eyes flush in the floor instead of using D-rings there isn't any metal standing above the trailer bed to get in the way of hauling cargo. There is only one slight problem with them. The circle is too small to drop a chain into it 'mid-span' and only works if you use the end of a chain. Roll-off trucks seem to have a bigger circle or a "T" at the top of the slot that allows chains to be used mid-span. Not a big deal because you can always pull the grab hook off your chains and just drop the end it.

Never have gotten a bad product from etrailer