# 1
B&W Extend-A-Goose Gooseneck Coupler - 2-5/16" Ball - 10" Offset - 24,000 lbs
I ordered this gooseneck coupler and it arrived in 3 days as promised. It's heavy so I took it to a friend to install it. Took maybe 15 min and I can actually turn my truck and trailer without worrys about blowing out the window like I did the week before. So happy I found these guys, super easy to work with. I would recommend this product to everyone with a short bed truck.
I was terrified at every turn of smashing my truck. This extend-a-goose is the answer! Make sure you measure the clearance of your gooseneck support to the bed rails to make sure that extending it the 11 inches doesn’t cause that angled part to impact your truck. The build quality is fantastic, however!! I’m not impressed with the “paint” down around the coupler...after only having it for a month or so I’m seeing rust stains (I will likely cover with a trash bag so it is not out in the elements since it protrudes last the gooseneck overhang. Bottom line, of you want a shortbed and a gooseneck this is a must!!! I no longer worry about crushing my truck and I can swing to about 80 deg off my trailer without worry (before it was maybe 50 degrees) And as always, shout out to etrailer for being a great parts supplier!!!
# 2
Bulldog Gooseneck Coupler - Adjustable - Round - 2-5/16" Ball - 30,000 lbs
Replacement on our hay trailer was the call for the hitch. It was easy to weld on and I like the pin on this hitch. It never moves like ones that are just jam nut tight. Can run down the road and not worry that this hitch will move out of ajustment. Fast shipping and a great company to work with.
Product is exactly what I needed for my 30 ft cattle trailer. Heavy duty material that will last longer than the trailer. Would definetly recommend this product to others.
# 3
2-5/16" Gooseneck Coupler Head with 1/2" Lock Pin, 30,000 lbs.
Great solid product
Very good product so far. Easy to weld and connect to the ball. The inside is a bit rough from the casting. Not sure how that is a negative or positive to hold grease.Pulled across the scale with @41k trailer. I reduced load after that but the coupler held, or should I say my welds.
# 4
Convert-A-Ball Multi-Cushioned Gooseneck Trailer Coupler - Round - 30,000 lbs
OK. Just installed the convert- A - Ball Multi -Cushioned Coupler this morrin. Took about 15 min. Took it for a test drive down the I10 just a mile from my front door. [ Casa Grande AZ.] It reduced the felt bumps and road jars by about 80%. I drove down the access road for a few miles. [ uneven, repaired spots, really ruff road.] Then got on the I 10 and drove between The Pinal exit and the McCartney exit. # lane just repaved about a year ago. Did not feel any road vibration that you get at 70 MPH. Other coulper go for 2 to 3 times this much. And require a lot of up keep. I would recommend this to anyone hauling horses,or any big trailer that whats a smoother ride.
Got stuck several times. Would not release. I finally had to cut it off. Cheap locking mechanism.
# 5
Ram Gooseneck Coupler - Topwind - 7" Adjustment - Square - 2-5/16" Ball - 30K
Not impressed with boxes that they were shipped in,holes and breaking up. The shipper must have been hard on them
The weld quality on this gooseneck coupler is horrible! Our fab shop will have to repair almost every weld on the coupler. For something that is supposed to be rated for 30K pounds I'd expect a certified welder to weld the coupler. But this is not the case because the undercut and lack of fusion on this coupler would not be present if a certified welder welded this coupler. Also, it came as bare metal not painted as shown in the picture. We are NOT satisfied at all with this product!
# 6
Pro Series Gooseneck Coupler - Adjustable - Round - 2-5/16" Ball - 25,000 lbs
I am very satisfied with the gooseneck hitch I ordered from you. The delivery was very prompt also. Attached is a picture of the trailer in progress. I will send a picture of the completed trailer when it is finished. I am very glad to find you. Thank you. Roy Ellerbee
Glad to see etrailer.com carry some fabricating parts. Modified this coupler to convert a fifth wheel to goose neck. Excellent product!
# 7
Ram Gooseneck Coupler w/ Load Bearing Pin - 8" Adjustment - Square - 2-5/16" Ball - 25K
Some of the welds looked a little rough and there was quite a bit of spatter on the tube, but with that said, there's no way you'll find a better value for the money. Since I had to weld the hitch on anyways, I cleaned the spatter off with a flap wheel and went over the welds I wasn't happy with. I wouldn't hesitate to purchase another one.
the picture on the internet for this item shows 2 jam bolts before you hit purchase. then after you hit purchase it shows a single bolt. im not sure what we received yet. but its confusing. other than that great service.
# 8
Bulldog Gooseneck Coupler - Adjustable - Round - 2-5/16" Ball - 20,000 lbs
I haven’t installed it yet but it looks of very good quality. The shipping was expensive but that’s just how things are now days. I am looking forward to making a new tongue hitch for my 5th wheel camper to convert it to gooseneck. This will work perfectly. Thanks
I recieved your new gooseneck piece for the repair on my trailer I bought that was built from scratch of an old man that passed away I bought from his window and have not yet had the opportunity to replace the old piece that would not interact with most other gooseneck applications because the pipe was not large enough to fit other applications out there so decided to change it to be compatible with other trailers
# 9
Ram Gooseneck Coupler w/ Load Bearing Pin - 8" Adjustment - Round - 2-5/16" Ball - 25K
Receive my product replacement gooseneck lockdown system built heavy duty simple to install and the locking system is monster us I think it will very much suit my needs easy to unlock and lock I would definitely be proud to endorse a product like this and you can’t beat the price everyone I looked at that was like this [was almost double the price] or better shipping was great and quick thank you
Haven’t installed the coupler yet, have to clean up a couple welds that went too far into the area where the ball goes then paint. Test fit into existing tube on trailer showed it was a little loose, not a big deal as it is tighter in the tube it came with. Overall happy with the hitch and price point.
# 10
Round Gooseneck Coupler with 28" - 38" Adjustable Height - 24,000 lbs
direct replacement for the old damaged coupler. works great!
Great heavy duty replacement! Shipped immediately and received within three days of my ordering.
# 11
Bulldog BX1 Gooseneck Coupler - Adjustable Height - Round - 2-5/16" Ball - 25,000 lbs
Perfect fit in the old receiver tube and the lower profile will allow me to level the trailer.
All the reviews said this is good for higher vehicles, to level a load. The distance from bottom hole to gooseneck is 10.5 inches, exact same hight of the coupler that came standard on my trailer. The raw finish comes with a nice coat of rust on it, so be prepared to clean all that up as well.
# 12
Bulldog Gooseneck Coupler - Adjustable - Square - 2-5/16" Ball - 25,000 lbs
Great product! Exactly what was on my pj dump trailer.
Good guality parts and exelant customer service from eTrailer staff. Itam was on back order from bully dog and etrailer staff did a great job of keeping me updated on my order.
# 13
Ram Gooseneck Coupler w/ Load Bearing Pin - 8" Adjustment - Round - 2-5/16" Ball - 30K
It's a great starting point for my extreme goosenecks I weld the reinforcement ring top and bottom and reinforce the latch mechanism which makes them just about indestructible . This is the six one that I've installed they get horribly mistreated and are all working fine
Product looks great, haven't welded it up yet but showed up in a very timely fashion
# 14
Pro Series Gooseneck Coupler - Adjustable - Round - 2-5/16" Ball - 25,000 lbs
the service was great ,had one item that was going to be a couple months later shipping and the folks at etrailer called to make sure that was fine but they ended up finding, another item that would work and had my order to me by the end of the week ,great service team at etrailer will definitely use them again
Love this hitch! Holds well and looks great! They were so much help with finding us the perfect hitch and shipped it out quickly.
# 15
Bulldog Gooseneck Coupler - Fixed Base - Round - 2-5/16" Ball - 20,000 lbs
Not the right size. Need help to return an get the correct size. After waiting 7 months.
everything went together perfectly. it is still working great . the finish is holding u[p , too.
# 16
Bulldog Gooseneck Coupler - Adjustable - Round - 2-5/16" Ball - 25,000 lbs
everyone was very nice and helpful. well made piece. thanks walter
Once I submitted my order- I received a email within hours stating "My order has been shipped "!! This is un-heard of! I received the order in 2 days - Free Shipping!! Customer Service is Top Level. I am a repeat Customer and have been 100% Satisfied with each order- Always packaged Well and Products are as represented in add - Buy with Confidence. Special Thanks to George J and Carol C and all the Staff at etrailer.com
# 17
Pro Series Gooseneck Coupler - Adjustable - Round - 2-5/16" Ball - 20,000 lbs
I just received this goosneck hitch coupler in the mail. After opening the box it was everything that the description said. It seems to have good solid welds and the coupler seams so function smoothly. I will be installing it on my dump trailer that I'm building in the weeks to come. I do not see any reason thus far why this product should fail or give me problems. I compared it too a goosneck trailer that I purchased new and have used a lot over the years and it looks like a identical coupler. So far I would recommend this product if your building or repairing your goosneck trailer.
well made at a good price point. Going to use this component to fabricate a custom gooseneck hitch for an older 5th wheel camp trailer, no photos yet.
# 18
B&W Defender Locking Gooseneck Coupler Inner Tube - Round - 2-5/16" Ball - 25,000 lbs
This fit the bill perfectly / exactly what I needed Great people to work with and they speak real "English" ! something that you dont find anymore The freight was very fast Thank you from Northwest Wyoming Don
They did not have the one I needed, but were quick to have an alternative. Great communication, will continue ordering.
# 19
Gen-Y Spartan Shock Absorbing Gooseneck Coupler - 5" Offset - 2-5/16" Ball - 3.5K TW
This seems to be an excellent upgrade to the coupler on my Belmont trailer. Less than 100 miles on it so far but the trailer seems to jerk the truck around less on these fine Pennsylvania roads. It is helpful to have an extra pair of hands when installing. The powder coating made the tube on the coupler a little thicker than the original. I used a wire brush and some spray lithium grease on the inside of the trailer tube and was able to install the new coupler just by working it back and forth with minimal powder coating coming off. My trailer is registered at 9,999 lbs which is why I went with the 3.5k TW option. Haven’t had an opportunity to put a machine on the trailer yet to see if that was wise or not but a load of 18 - 6”x6”x12’ pressure treated beams barely moved the indicator. After my first trip I opted to change it to using the hole closest to the coupler as the trailer had a little too much angle back towards the last axle. Even in the bottom hole I still have 9” of clearance between the top of my tailgate on my Ram 2500 and the trailer.
The difference is substantial! I won’t say you can’t tell the trailer is back there but the ride comfort is outstanding!!!!
# 20
Gen-Y Spartan Shock Absorbing Gooseneck Coupler - 5" Offset 2-5/16" Recessed Ball 3.5K TW
With my trailer which is only a 6 k trailer I bought the 7.5k hitch yet empty it is maxed out wish there was a way to adjust
E trailer customer service stayed in contact with me through the entire process. It took a few weeks to be delivered but I was in no hurry so plan accordingly. The Spartan hitch was as advertised. The only negative feed back I have is that the neck pin didn’t have a shoulder so it would go all the way through the holes. I use my existing through bolt anyway so I didn’t need it. Again plan accordingly. Not to be confused with the ball hitch pin. I’m strictly speaking of the slide neck adjustment pin. Overall very pleased with etrailer and gen y.
What our customers are saying:
"Easy place to shop. Fast delivery and great products. Very happy with my purchase."