Trailer Brake Controller Specs:
Features:
Proportional brake controller mounts on your trailer to keep your cab clutter-free. Keep towing simple and convenient with a key fob for remote control of the brake controller. Nothing installs in your vehicle, so you can tow with any truck.
Installation Notes:
More Information >Trailer Brake Controller Specs:
Features:
Proportional brake controller mounts on your trailer to keep your cab clutter-free. Keep towing simple and convenient with a key fob for remote control of the brake controller. Nothing installs in your vehicle, so you can tow with any truck.
Installation Notes:
You need item ETBC7L ($121.34) to install your controller.
More Information >Trailer Brake Controller Specs:
Features:
Wireless brake controller mounts on your trailer to keep your cab clutter-free. Keep towing simple and convenient with a handheld, Bluetooth remote control. Nothing installs in your vehicle, so you can tow with any truck that has a 7-way.
Installation Notes:
More Information >Trailer Brake Controller Specs:
Features:
Wireless brake controller mounts on your trailer to keep your cab clutter-free. Keep towing simple and convenient with a handheld, Bluetooth remote control. Nothing installs in your vehicle, so you can tow with any truck that has a 7-way.
Installation Notes:
You need item ETBC7L ($121.34) to install your controller.
You may also need a 4-Flat connector to complete your wiring.
More Information >Videos
for Trailer Brake Controller
Help Articles
for Trailer Brake Controller
Expert Answers
for Trailer Brake Controller
While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the…
view full answer...The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.
view full answer...The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.
view full answer...The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your…
view full answer...A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...The number you provided,…
view full answer...The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you,…
view full answer...To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…
view full answer...For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…
view full answer...If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…
view full answer...