Trailer Brake Controller Specs:
Features:
This proportional brake controller is designed to keep towing simple. Includes an LED braking indicator, a slide-bar manual override, and a knob to adjust braking power. Mounts easily within a 90-degree vertical range.
Installation Notes:
You need item ETBC7 ($129.02) to install your controller.
You may also need a 4-Flat connector to complete your wiring.
More Information >Trailer Brake Controller Specs:
Features:
This proportional brake controller is designed to keep towing simple. Includes an LED braking indicator, a slide-bar manual override, and a knob to adjust braking power. Mounts easily within a 90-degree vertical range.
Installation Notes:
Vehicles with the 7-Way tow package have the blue output brake wire already ran from the back to the front. It is located under the dash near the emergency brake pedal.
If your vehicle has a round plug with a cap inside the driver's side frame rail instead of a bundle of wires in the jack storage compartment, use part # 30955.
Some models will require a wiring kit to run wire to the battery. This may require drilling a hole in the firewall to run the wire. You may use kit 5506 which includes 20, 30, and 40 amp breakers.
More Information >Trailer Brake Controller Specs:
Features:
...in the USA Specs: Application: trailers with up to 2 axles (4 brake assemblies) Compatible with electric brakes only Dimensions: 6-1/2" long x 3" wide x 1-5/8" tall Mounting angle: -35 degrees...
Installation Notes:
Vehicles with the 7-Way tow package have the blue output brake wire already ran from the back to the front. It is located under the dash near the emergency brake pedal.
If your vehicle has a round plug with a cap inside the driver's side frame rail instead of a bundle of wires in the jack storage compartment, use part # 30955.
Some models will require a wiring kit to run wire to the battery. This may require drilling a hole in the firewall to run the wire. You may use kit 5506 which includes 20, 30, and 40 amp breakers.
More Information >Trailer Brake Controller Specs:
Features:
...in the USA Specs: Application: trailers with up to 2 axles (4 brake assemblies) Compatible with electric brakes only Dimensions: 6-1/2" long x 3" wide x 1-5/8" tall Mounting angle: -35 degrees...
Installation Notes:
You need item ETBC7 ($129.02) to install your controller.
You may also need a 4-Flat connector to complete your wiring.
More Information >Videos
for Trailer Brake Controller
Help Articles
for Trailer Brake Controller
Expert Answers
for Trailer Brake Controller
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.
view full answer...The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.
view full answer...The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your…
view full answer...I've never heard of an actual third brake light connector on a camper shell to…
view full answer...You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…
view full answer...The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…
view full answer...On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…
view full answer...The number you provided,…
view full answer...To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…
view full answer...