Trailer Brake Controller Specs:
Features:
The large buttons and colored LCD display on this proportional brake controller make it easy to see and easy to use. Store and customize your settings so you can easily swap out trailers and drivers and get towing.
Installation Notes:
You need item ETBC7 ($129.64) to install your controller.
Some models have the brake (blue) and hot lead (orange or red) wires already ran to the rear of the driver side frame rail. However, these wires are hard to access and additional wire will be needed. We still recommend using part ETBC7.
You may also need a 4-Flat connector to complete your wiring.
More Information >Trailer Brake Controller Specs:
Features:
This proportional brake controller has simple controls and a digital display for diagnostic information. Includes 3 boost levels, a slide-bar manual override, built-in battery protection, automatic leveling, and continuous diagnostics.
Installation Notes:
You need item ETBC7 ($129.64) to install your controller.
Some models have the brake (blue) and hot lead (orange or red) wires already ran to the rear of the driver side frame rail. However, these wires are hard to access and additional wire will be needed. We still recommend using part ETBC7.
You may also need a 4-Flat connector to complete your wiring.
More Information >Trailer Brake Controller Specs:
Features:
Power output and braking aggressiveness can be easily adjusted with built-in buttons on this time-delayed brake controller. Includes digital display and manual override. Activates brakes with a preset intensity.
Installation Notes:
You need item ETBC7 ($129.64) to install your controller.
Some models have the brake (blue) and hot lead (orange or red) wires already ran to the rear of the driver side frame rail. However, these wires are hard to access and additional wire will be needed. We still recommend using part ETBC7.
You may also need a 4-Flat connector to complete your wiring.
More Information >Videos
for Trailer Brake Controller
Help Articles
for Trailer Brake Controller
Expert Answers
for Trailer Brake Controller
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…
view full answer...While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the…
view full answer...The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.
view full answer...The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…
view full answer...If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your…
view full answer...Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you…
view full answer...To see all of the correct wheel and tire combos…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
view full answer...The number you provided,…
view full answer...