Filter Questions and Answers:

reset filter

Expert Answers about Trailer Jack


  • Recommended Electric A-Frame Trailer Jack for 2011 Open Range Journeyer 340FLR
  • Tongue jacks are often rated higher than the weight of the trailer tongue they will be supporting. For tongue jack to meet your needs, I recommend the etrailer.com Electric Jack w/ Footplate - A-Frame - 25-1/8" Lift - 3.5K - Black # EJ-3520-BBX. This jack will mount to the same location on your trailer tongue A-frame and will give you a drop leg as well as a really nice LED light on a separate switch to help with connecting or disconnecting. If you want what I consider to be the best...
    view full answer...

  • Replacement Follow Landing Gear Leg for 1998 Fleetwood Savanna 5th Wheel
  • I have a few different options for you depending on the route you would like to take. However, regardless of which route you pursue you will need to take some measurements of your outer jack tube length and weld stop spacing. If you are handy and the bevel gear inside your jack leg is the only one that is damaged then you can just obtain the Follow Jack Repair Kit for Stromberg Carlson Landing Gear part # LG-146060. However, if you don't want to mess with repairing your old jack leg or...
    view full answer...

  • How to Correct Air Leaking from Tires on Trailer Valet Trailer Mover STC-V211
  • If the pneumatic tires on your Trailer Valet # STC-V211 are needing to be aired up each time you use your trailer I suggest either using a tire sealer product like Slime Tire Sealant # SLM10007 or if that does not solve the issue replacing your tires' inner tubes with part # TVIT. The tire on my wheelbarrow used to leak slowly until I applied some sealant. Since the sealant option is less costly I suggest trying that before replacing the inner tubes. The main reason solid tires are...
    view full answer...

  • Installation of etrailer Landing Gear
  • The Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs # RVLG-8HDL will simply mount to the weld-on brackets by being bolted on. While an online copy of the manual is not available for this specific landing gear, I did cut out a portion of the Stromberg Carlson Manual Landing Gear Set - Weld On - 34-7/8" Lift - 8,000 lbs # LG-183708 so you can take a look. In regards to the brackets you asked about, the Replacement Weld-On 5th Wheel Landing Gear Leg Bracket # LC113511 will work with...
    view full answer...

  • Replacement Parts Available for the RAM Trailer Jack Part # TJD-7000S
  • I do have several replacement parts available for the RAM Trailer Jack part # TJD-7000S but not an all inclusive rebuild kit. Instead you will need to select from the components listed below and repair the jack as needed. The most common fault on the above trailer jack is the spider gears and in order to replace them you will want to use part # TJD-7000S-GR. The rest of the replacement parts we have for the jack are listed below. If you can identify what is not working on the jack I would...
    view full answer...

  • Recommended Replacement Landing Gear for 2007 Pilgrim 40 Foot 5th Wheel Trailer
  • On your 2007 Pilgrim 40 foot 5th wheel trailer, I recommend using the Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs # UF17-943010. This landing gear will allow you to adjust independently for easy and quick leveling. The leg will travel 1 inch every 15 seconds and has drop legs for even faster compatibility. I've attached a diagram for you to see the connection points based on the weld stops so you can determine if it will bolt right in or if modifications to your...
    view full answer...

  • Best Landing Gear Upgrade Options for 5th Wheel Trailer
  • We do have motors that you can add to your landing gear. For example, the Landing Gear Set # RVLG-8000 can be operated with the manual crank # RVLG-HDL but you can also add the motor # LC142178 and switch # LG-145236 for effortless operation on your end. The next upgrade for landing gear is the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010. This is rated for up to 12,000 lbs and operates via separate motors so you can easily level your 5th wheel trailer without using blocks...
    view full answer...

  • Replacement Landing Gear for 2004 Dutchman Sport 30 Travel Trailer
  • Landing gear is designed to stabilize a portion of your trailer's weight, not to support the full GVWR of your trailer. From what I found online, your 2004 Dutchman Sport 30 has a GVWR of 9,764 lbs, so a set of 8,000 lb landing gear (combined) would be more than enough to support the front of your 5th wheel trailer. The Bulldog Tandem Landing Gear Set # BD500162, you were looking at, would work as a replacement. There are just bolts already installed where you'll mount your existing...
    view full answer...

  • Can Ultra-Fab Ultra Scissor Jacks Be Used without Leveling Blocks
  • The # UF48-979002 feature oversized footplates that are 4-1/2" wide by 9" long, so you could use them without leveling blocks. However, it's not uncommon for people to use leveling blocks like # A10-0918 or even wooden blocks under these jacks to provide extra stability (see photos). This is especially helpful in soft surfaces like grass or dirt. What you do want to make sure is that you chock your wheels to prevent your travel trailer from rocking and rolling when parked. For that,...
    view full answer...

  • Atwood Landing Gear Replacement for 36 Long Landing Gear
  • To replace the Atwood landing gear on your 5th wheel trailer you will need to measure the distance between your weld stops. This is typically 15-1/2" on the inside and 17-1/2" on the outside (see attached photo). We do have replacement options but since Atwood is no longer in the landing gear business you need to replace your whole landing gear set to ensure that the gear ratio and strengths are the same. If your weld stop locations match the picture then I recommend using the 8,000...
    view full answer...

  • Trailer Dolly Options for a 4,500 lb Travel Trailer
  • If you are looking for something that stays permanently attached to the trailer then the only thing we have is the Trailer Valet 5X # STC-V211 because it mounts directly to the frame and has a swivel feature for when you are traveling. You can also use the drill attachment # TVDA to help make moving the trailer easier/quicker. This has an automatic brake as well but the max tongue weight capacity if 500 lbs so if your will exceed that at all then you need to upgrade. Aside from this...
    view full answer...

  • Trailer Jacks Manufactured in the USA
  • There are some Dutton-Lainson trailer jacks that are made in the USA as well as a few that are not. Any jacks that we carry that are made in the USA have that as part of the description to help set them apart. Currently we have the following options: Pull Pin, Easy Swivel Trailer Jack with 8" Wheel - Sidewind - 1,500 lbs. # DL22800 Pull Pin, Easy Swivel Trailer Jack with 6" Wheel - Sidewind - 1,000 lbs. # DL22560 A-Frame Trailer Jack - Sidewind - 1,000 lbs. by Dutton-Lainson # DL22530 Pull...
    view full answer...

  • Recommended Replacement Landing Jack System for 2008 Keystone Montana Mountaineer 345DBQ
  • For your 2008 Keystone Montana Mountaneer 345DBQ, the Lippert Replacement Lead Leg for Keystone Montana 5th Wheel Landing Gear # LC178653 and follow leg # LC178652 are a perfect replacement. These parts are exactly what you need for your trailer. If you want the entire replacement kit, you can use the Lippert Manual Landing Gear Set with Handle - Weld On - 37" Lift - 6,000 lbs # LC333966 or electric # LC333964 which will have only one option of weld stops for your trailer. I've...
    view full answer...

  • Is There a Way to Replace Cracked Screen on Lippert Smart Jack
  • The only way to get a new control panel would be to replace your entire Smart Jack with part # LC643589. I reached out to my contact at Lippert who confirmed that the only replacement parts for the jack includes hardware like the pin or the footplate. With this being the case your best option to protect the buttons is a trailer jack cover like part # UF38-944020. If you'd rather use a different jack then I recommend the Husky Brute Electric Trailer Jack # HT87247 because it is rated...
    view full answer...

  • How To Install the Landing Gear Set Part # RVLG-8000
  • The installation of the Landing Gear Set part # RVLG-8000 will be fairly straight forward. Basically, you will need to have a metal support structure so you can attach welded tabs part # LC113511 to it, 15-1/2" apart. Once these are installed you can then mount the jack tube and modify a cross-shaft that connects the two together which is included. Then, you will need to obtain a handle, the Crank Handle part # RVLG-HDL to raise and lower the legs. Unfortunately, we do not have a video...
    view full answer...

  • How to Manually Operate the Ultra-Fab Deluxe Electric Landing Gear Set
  • Good question; if for some reason there is an issue with the power or motor, you can manually operate the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010. I took a look at the instructions, and the accompanying cut out from them explains what you'll need to do. There are four screws that hold the motor and gear assembly on, and you'll need to remove those and turn the slotted shaft with a flathead screwdriver. Then, if ever need be you can get a replacement motor with the...
    view full answer...

  • Replacement Drop Leg Extension for Lippert Power Jack with Additional Height Needed
  • The Lippert Electric Trailer Jack with Footplate - A-Frame - 18" Lift - 3,500 lbs - Black # LC285318 has a drop leg available that will give an extra 4-1/2 inches with # LC405217.
    view full answer...

  • Replacement for Sidewind Gooseneck Trailer jack
  • Thank you for the photos, they are appreciated, though unfortunately there are no crank handles I can confirm will fit your specific jack. The best option we have is a replacement jack for your trailer. There are budget-friendly options such as the Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-7/8" Lift - 7,000 lbs # TJD-8000S I recommend checking out as well as the more heavy duty options like the Pro Series Square Jack - Drop Leg w/ Non-Spring Return - Sidewind...
    view full answer...

  • Electric Tongue Jack for Straight Pole Tongue Recommendation
  • The only electric power jack we have for the pole tongue is the Fulton XLT Powered Drive Trailer Jack - Drop Leg - Side Mount - 22" Lift - 2,500 lbs # F141401. This jack will allow up to 22 inches of lift using the 8 inch drop leg and 14 inches of screw travel and will fit 3 to 5 inch tall frames. The only way to use a caster wheel on this jack is to remove the drop leg and use a caster wheel like the Pro Series 6", Detachable Caster w/ Pin for 2" Diameter Jacks # PS1400750340. The...
    view full answer...

  • Bolt-On Side-Mount Dual Wheel Trailer Jack Recommendation for Utility Trailer
  • Since you want a side-mount jack that will work on dirt/grass surfaces I suggest a dual-wheel type such as the MaxxTow # MT70149. Dual wheel will spread the weight over a larger area and help the jack function on such softer surfaces. The jack offers bolt-on installation, a hefty 1500-lb tongue weight rating, pull-pin swivel operation and 12-inches of lift. If the surfaces are very soft or rutted you may instead prefer the Trailer Valet 5X Swivel Jack and Trailer Mover # STC-V211. This...
    view full answer...

  • Replacement Scissor Jack for a 2017 Rpod 179 Hood River Edition
  • While I do not know which specific jack make and model came on your Rpod originally you can install pretty much any other similar jack, such as Ram Scissor Stabilizer Jack # TJSC-24, as a replacement. The mounting holes likely will not perfectly line up but it wouldn't take much effort to add a new hole or two to properly install the jack. Since the original was also welded I do recommend doing the same with the new jack. Any welding should be done by a professional welder.
    view full answer...

  • Replacement 8 x 2 Wheel for Fulton Magnum Trailer Jack
  • Thanks for the picture of your jack! From that I can tell you need the replacement wheel part # F0933323S00 and you'd be set.
    view full answer...

  • Jack With Wheel Compatible with 500 Gallon Water Tank Trailer
  • For your trailer, the best option for a wheel is the Trailer Valet 5X Swivel Jack and Trailer Mover # STC-V211. This is rated for up to 5,000 lb trailer with 500 lb tongue weight. This is due to the pneumatic dual tires. Most trailer jacks with wheel are only rated for about a 1600 lb capacity maximum due mostly to the plastic wheel. The Dutton-Lainson Square Swivel Jack w/ 3" Wide Wheel - Sidewind - 12" Lift - 1,700 lbs # DL22339 is the most heavy duty option we offer other than...
    view full answer...

  • Recommended A-Frame Jack with Most Ground Clearance
  • The distance from the bottom of the mounting flange to the bottom of the outer tube on the Bulldog Round, A-Frame Jack part # BD155033 is 3-1/2". The mounting flange is 3/16" thick. I have attached a photo of these measurements for you as well. If you need something with even more clearance then the only other option we have is the Ultimate Trailer Jack part # 322-RDJ-2K which measures 1-3/4" with the jack fully retracted and the collar at the lowest setting. I have attached a review...
    view full answer...

  • Replacement Cap for RAM Electric A-Frame Trailer Jack
  • For the replacement cap that will cover the manual override on your Electric A-Frame Jack # EJ-3520-BBX, you will just need the Replacement Cap # EJ-3520-BCP. This will include one cap for your jack.
    view full answer...

  • Replacement Drop Leg and Cap for Fulton Square Jack
  • For your drop leg, I recommend the Bulldog Square, 18-1/8" Tall Drop-Leg Tube - 7,200 lbs to 10,000 lbs # BD70129201 which has a tubing width of 2-1/4 inches. The replacement cap for the Fulton jacks is # F0917504-00. If you need the pin for the drop leg, use # BD500337.
    view full answer...

  • What Kind of Oil Should be Used for Oil Bath Hubs
  • If you are wondering how to lubricate the Bulldog Square Jack # BD182701, that you referenced, then you will simply need to fill it with grease via the grease fittings. If you are referring to an oil bath on your hubs, like the Kodiak XL ProLube Kit # XLPROLUBE1980KIT, then we do have bearing lube listed as part # XLPROLUBE which is an 8 Ounce bottle of synthetic 90 weight oil. I have attached a photo of the back of the bottle which reads "Fill to manufacturer's specifications". I...
    view full answer...

  • How to Pick Out Landing Gear Replacement for 2003 Nomad Scout FW Model 237
  • In order to pick out a direct replacement for the landing gear on your trailer we would need to know the distance between the mounting brackets. Otherwise you could just have the brackets removed from your trailer by a qualified welder and then install the brackets that come with the Bulldog Tandem Landing Gear Set # BD500162. Either way this landing gear set would work well for you, you just might have to have the brackets of your trailer removed and then install the brackets of the #...
    view full answer...

  • What Size Pipe Mount Does the Bulldog Square Jack w/ Round Pipe Mount BD182524 Use
  • The Bulldog Square Jack w/ Round Pipe Mount part # BD182524 is designed to be used with the Bulldog Weld-On Jack Pipe Mount part # BD005122 which is 4" diameter with a 7/8" pin hole. I don't know of any jacks off-hand which match your pipe mount so you are going to be much better off just having a new pipe mount welded on. The distance from the center of the mount to the bottom of the footplate is 17" while retracted and 29.6" while extended.
    view full answer...

  • Dual Jack Landing Gear for Gooseneck Trailer Transporting Large Water Tank
  • The weight of 1600 gallons of water, without the water tank's own weight factored in, is about 13,350-lbs. For such a high-weight application I suggest Bulldog Square Jacks # BD182804 and # BD182805 along with Connecting Rod # BDCS730300. Two jacks are definitely the way to go. If you wish to motorize this jack setup you can also add motor kit # BD1824200100. I also recommend you first determine the actual pin weight of the loaded trailer so that you can be sure to select jacks with...
    view full answer...

  • Comparing the Stromberg Carlson Trailer Jacks # JET-5000NG VS JET-5000
  • All-around the Stromberg Carlson Electric Trailer Jack # JET-5000NG is nicer than the # JET-5000. The bearings in the part # JET-5000NG allow it to raise and lower much smoother and quicker, the size of the head is a bit smaller and the lighting is nicer too. For how similar the price is between the two the # JET-5000NG really is the winner.
    view full answer...

  • Replacement Landing Gear for a Keystone Laredo 5th Wheel Trailer
  • Bulldog Tandem Landing Gear Set # BD500162 is a great option for a manual set to replace the landing gear on your Keystone Laredo. I have linked a video review for you. The handle is not included so use # BD500203 to add the crank handle. For an electric set you could use # RVLG-8HDL and add motor # LC142178 and, if you don't already have one, a switch # LC145236.
    view full answer...

  • Can Power for the Bulldog Powered Drive Trailer Jack Come from the 7-Way Trailer Connector
  • The installation of a 7-way trailer plug like the Pollak Black Plastic, 7-Pole, RV-Style Trailer Connector part # PK12706 on an electric a-frame trailer jack like the Bulldog Powered Drive Trailer Jack part # BD500200 is not something that we have the ability to offer you unfortunately. However, this process will be extremely simple as all you need to do is insert the power wire on the jack into the correct terminal on the 7-way and then tighter down the screw. It should not take more than...
    view full answer...

  • Trailer Pipe Mounted Swivel Jack with Retracted Length Measurements
  • The Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Sidewind - 10" Lift - 2,000 lbs # PS1401060303 has an overall length when retracted of 16-5/8 inches. This jack does not have a wheel. For a similar jack with a wheel, I recommend the Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 10" Lift - 2,000 lbs # BD1541150301 along with the Replacement Heavy-Duty, 6" Caster for 2" Diameter Bulldog Jacks - 1,500 lbs # BDCP555. Without the wheel, the retracted length of this jack is...
    view full answer...

  • Mounting Plate for F1413100334 Fulton F2 Swing-Up Trailer Jack
  • After looking closely at the photo, it looks like the # F1413100334 jack is mounted to the trailer frame using the # F500277 weld-on mounting plate. This is the recommended method of installing this jack.
    view full answer...

  • Recommended Extreme Off-Road Trailer Jack w/ Dual Wheels for 23" Trailer Frame Height
  • If you are needing your trailer frame to be 23" from the ground to the top of the frame then I recommend going with the Extreme Off-Road Trailer Jack w/ Dual Wheels # ORJW500D with the 16-3/4" lift because the part # ORJW350D with the 12" lift will be just shy of what you are needing (just under 22"). The 16-3/4" lift actually has a higher tongue weight rating too so you don't have to worry about that.
    view full answer...

  • Replacement Jack for Boat Trailer With Wheel That Swivels Easily
  • We have a great option for a boat trailer jack that is going to easily swivel with the Fulton XLT jack. Keeping in mind that all jack wheels can struggle turning if there is too much weight on them, the XLT has a very high-quality caster and wheel and is designed with easy maneuverability in mind. The jack has what is called a "Sharkskin" finish as well to keep it from getting scratched and damaged, and is designed to fit 3" x 3" or 3" x 4" trailer frames. It comes in either silver or...
    view full answer...

  • Can a Breakaway Battery be Used to Power an Electric A-Frame Trailer Jack
  • If your breakaway system is powered by its own battery then it is likely a 5 amp hour battery which is not high enough to power an electric trailer jack, such as # BD500199, since they can draw about 30 amps under load. The other issue is that a breakaway system needs its own dedicated battery and should not be shared by other 12 volt accessories. If your trailer has a 7-Way trailer connector with functioning 12 volt circuit you could use electric jack # 3370093500 which plugs into a...
    view full answer...

  • Can Ultimate A-Frame Trailer Jack 322-RDJ-2K Be Completely Removed from Collar Assembly
  • Yes, the Ultimate A-Frame Trailer Jack # 322-RDJ-2K uses a separate trailer-mounted A-frame collar that allows complete removal of the jack tube from the collar. Please note that the jack ships with a black plastic wedge that is held in place with a small retaining bolt. If this bolt and wedge are removed from the jack then the entire jack can be lifted up and out of the collar to give you the clearance you need for opening the rear door on your Jeep. Please refer to the linked photo...
    view full answer...

  • Types of Jacks Suitable to Stabilize Equipment Trailer During Loading
  • We have various jack and stabilizer products that you can consider for addition to the rear of your equipment trailer to support it during loading processes. I linked our main page for such items so you can see all we offer. If you want a low-cost and lightweight option that does not require permanent installation you might look at the Ultra-Fab Stackable Stabilizers # UF48-979003 (a set of 2) or the 4-piece set # UF48-979004. These offer 17-inches of lift and the 4-piece set weighs...
    view full answer...

  • How Much Weight Can Extreme Off-Road Ratcheting Trailer Jack ORJW1SU Move Effectively
  • The Extreme Off-Road Ratcheting Trailer Jack # ORJW1SU has a static weight capacity (load support) of 770 lbs but ARK does not do a test for dynamic load rating, so it's hard to say what kind of trailer load this jack could move. If you're looking for something specifically designed to move your trailer farther distances, I recommend the Trailer Valet XL Trailer Dolly with Chain Drive # TVXL25 with a 2-5/16" hitch ball or # TVXL2 with a 2" ball. Both designed to move trailers with up...
    view full answer...

  • Recommended Electric A-Frame Jack for Trailer with 5,824 Dry Weight
  • When looking at electric A-frame jacks, the important weight to consider on your trailer is its tongue weight. This is the weight that the jack will actually be lifting and not its total loaded weight. A trailer's tongue weight should be 10 to 15 percent of its total weight. If your trailer has an empty weight of 5,824 pounds, we can estimate a dry tongue weight of around 580 to 875 pounds. Note though that you will want to also account for the loaded cargo weight as well when the trailer...
    view full answer...

  • Do the Scissor Stabilizer Jacks Come with Install Hardware
  • The Scissor Stabilizer Jacks part # TJSCHD-24-4 do not come with installation hardware. That said, we do offer the self-tapping screws you'll need for this using part # FA1131822. In regards to quantity, you'll need a total of 16.
    view full answer...

  • Wiring Electric Jack to Plug Into 7-Way on Tow Vehicle
  • Although wiring an electric jack like the etrailer.com # EJ-3520-BBX you referenced to a dedicated battery on the trailer is the preferred solution for ensuring you get the needed power, you can indeed wire it to a 7-Way plug like # A7WCB for it to be connected to the 7-Way on your truck when needed. If you don't yet have an electric jack, we actually have a 3,500 pound unit available with the Buyers Products # 3370093500 that is designed to be used this way right out of the box. This...
    view full answer...

  • Recommended Flatbed Cargo Trailer Stabilizer Leg for Rear of Trailer
  • For your Sure Trac ST9614 HLODOD-B-140 trailer I recommend adding the Ultra-Fab Ultra Scissor Jacks - 24" Lift - 6,500 lbs - Qty 2 # UF48-979002. I believe these will work well to stabilize your trailer for loading. They can be adjusted using the hand crank or you can use the Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks # UF48-979005 if you prefer. If you want more of a solid mount drop leg stabilizer that you would weld on, we have the Square Drop Leg Stabilizer Jack...
    view full answer...

  • Replacement Parts for the Bulldog Powered Drive Trailer Jack part BD500199
  • I have attached for you a list of the replacement parts that are available for the Bulldog Powered Drive Trailer Jack part # BD500199. I am not sure which part in particular that you are referring to but if it is not listed below then you would unfortunately have to replace the jack. The Ultra-Fab Electric A-Frame Jack part # UF38-944014 would be a good cost effective replacement for this if needed. Replacement Extend and Retract Switch part # BD500363 Replacement Manual Override Crank...
    view full answer...

  • Difference Between Bulldog Velocity Series Electric Landing Gear Jacks
  • The only difference is that one of the Bulldog Velocity Series Electric Landing Gear Jacks comes with the Remote Control for Bulldog Velocity Series Electric Landing Gear Jack # BD500372 while the other does not: - With Remote Control: Bulldog Velocity Series Electric Landing Gear Jack # BD185400 - Without Remote Control: Bulldog Velocity Series Electric Landing Gear Jack # BD185402 Otherwise, both have a 12,000 lb capacity and are very fast jacks, lifting 20 inches in 60 seconds....
    view full answer...

  • Jack for Tire Replacement on Lifted Jeep
  • Our scissor jacks should not be used to lift a car to replace a spare tire as they were not designed for that application. Instead, depending on how far you need to lift, you may be able to use the Powerbuilt Unijack # ALL620470, which can lift up to 4,000 lbs and a range between 8-5/8" and 18-3/8", or Powerbuilt Unijack # ALL620471 which has a lift capacity of 6,000 lbs and a lift range between 11" and 21". After lifting your vehicle the jack locks into place with a safety bar so you would...
    view full answer...

  • Replacement Manual Override Crank and Brake Release for Husky Brute Electric Jack
  • He/She will want the Replacement Manual Override Crank w/Brake Release Handle for Husky Brute Jacks - 7/16" Hex Head # 87639. I've attached a photo to assist as well as a video.
    view full answer...

  • Troubleshooting Ultra-Fab Phoenix Electric Tongue Jack That Won't Extend or Retract
  • The Ultra-Fab Phoenix Electric Trailer Jack with Remote- 5,500 lbs # UF38-944055 or 4,000 lb # UF38-944040 without remote sounds like it may have a mechanical issue. I recommend using the manual crank to extend or lower the jack. If you can use this, then you isolate the issue to electrical with a possible bad ground or motor issue. If you can't physically move the jack with the manual crank then we know the issue is mechanical with the inner rod seized or having stripped threads. If...
    view full answer...

  • Replacement Swivel Jack for 2005 EZ Loader Boat Trailer
  • Hi Rob! The F2 series uses a different style plate that you have so you'll either have to replace your weld-on bracket with the bracket that comes with the F2 # F1413060334 or you can use the bolt-on option # F1413020134 OR you can use the adapter # F500320 with either of the F2 options mentioned above.
    view full answer...

  • Replacement for Fulton 12K Magnum Series HD Jack
  • The photos you attached did not come through but in order to replace your Fulton 12K Magnum Series HD Jack, I recommend using the Bulldog Square Jack part # BD182701 which has a 12,500 lbs capacity and offers up to 12-1/2" of lift. Unfortunately, Bulldog does not offer the extension rod that will allow you to operate the jack from the side of the trailer as they will vary depending on the trailer. I am certain you would be able to find everything you need to make one at a local hardware...
    view full answer...

  • Fuse Location on etrailer.com Electric Jack # EJ-3520-BBX
  • On the etrailer.com Electric Jack w/ Footplate # EJ-3520-BBX that you referenced the 30 amp barrel fuse like # EJ-FUSE is located in a flared opening right where the black power wire comes out of the motor housing. It is very easy to access and replace if the need arises. I have attached a short video demonstration on this jack that you can check out as well.
    view full answer...

  • Can etrailer EJ3527-BBX Trailer Jack Be Powered From 7-Way Trailer Connector on 2020 Ford F-150
  • The etrailer brand # EJ3527-BBX is equipped with a 7-way plug that can be plugged into the 7-way trailer connector on your 2020 Ford F-150. This being said, for more reliable operation, it's best to install a battery on the trailer and run a powered jack from that. The etrailer # EJ-3520-BBX jack is designed to be wired directly to a trailer mounted battery. You can wire the 12-volt feed from the 7-way to the trailer mounted battery. It won't charge the battery completely if it gets...
    view full answer...

  • Small Powered Trailer Jack Recommendation for Tailgate Clearance
  • I have a few different options for you and it all depends on what you're wanting out of a trailer jack for your 2017 Forest River Rockwood Signature Ultra Lite 2703WS. The absolute best clearance you'll get is with the Trailer Valet JXC Trailer Jack w/ Footplate # TV94FR because it uses a hand crank, but then you can use your drill then you want it to operate faster. Using this means you don't have to make connections to your trailer battery plus you won't have the trailer jack motor...
    view full answer...

  • How to Charge a Trailer Battery for Use with a Bulldog Jack
  • What you described is actually the best solution! Connecting your battery to 12V Power wire from the 7-Way on your trailer is a great way to provide a maintenance charge on your battery to operate a Bulldog jack like part # BD500199. Mounting a battery inside a box like part # 329-HM300BKS inside your trailer will further help to keep your battery safe from the elements (although battery boxes do a pretty good job at that). Please note that the 12V power from your vehicle will not...
    view full answer...

  • Size of Footplate or Caster With Wheel That Fits Ultimate Trailer Jack A-Frame Jack
  • You can add either a footplate or caster to the Ultimate Trailer Jack # 322-RDJ-2K. This jack has a 2-1/4" outer tube and 2" inner tube and the correct footplate is # JF-101BK while for a caster with wheel assembly # JC-102 is a fit and attaches to the inner jack tube. I've added links to video reviews of each of these parts for you to take a look at.
    view full answer...

  • Electric Conversion Compatibility for Holland Binkley Model 48000 Series Jack on Horse Trailer
  • The Holland Binkley model 48,000 series jacks are very similar to the Bulldog Square Jack - Drop Leg w/ Spring Return # BD182815 which can utilize the Bulldog Powered-Drive Kit for Single-Speed Jacks w/ 12,000-lb Capacity # BD1824200100. Your current jacks are not compatible with the kit to my knowledge so you would need to replace the jacks in order to upgrade to the motor kit. Another option is to use the Bulldog Velocity Series Electric Landing Gear Jack - 24" Lift - 12,000 lbs...
    view full answer...

  • Availability of Wiring Diagram for the Replacement Power Switch # EJ-3520-PSW
  • I am attaching a picture of the Replacement Power Switch # EJ-3520-PSW when it is properly installed on the Electric Jack w/ Footplate # EJ-3520-BBX but unfortunately there isn't a wiring diagram available. If you be mindful to note which position each wire is supposed to be in when you disconnect your current switch you simply just have to install this switch in the same way.
    view full answer...

  • Mounting Hole Spacing of etrailer and Ultra-Fab Scissor Jacks
  • We do have an option for you, but I have added the mounting hole spacing dimensions of the Scissor Stabilizer Jacks w/ Handle - 18-3/4" Lift - 5,000 lbs # TJSCHD-24, and as you can see, none line up exactly with your pre-drilled holes, although it is close, with two of the holes measuring 5-3/16" apart. The jacks that do have the spacing you need are the Ultra-Fab Ultra Scissor Jacks - 24" Lift - 6,500 lbs # UF48-979002, which have the two closest bolt holes at 5" apart as you can see...
    view full answer...

  • Stabilizer Jack Recommendation for Stored Boat Trailer To Support While in Storage
  • Scissor style stabilizer jacks like the Leveling Scissor Jack Set # JSC-24 would be your best option. These were designed to stabilize camper trailers but would work great for what you are wanting. I attached a picture of what they look like in use plus a review video for more info as well.
    view full answer...

  • Replacement Electric Landing Gear for Horse Trailer
  • Sorry to hear your system broke and there aren't replacement parts available for your horse trailer. The Bulldog Velocity Series Electric Landing Gear Jack - 24" Lift - 12,000 lbs # BD185400 is a good replacement for your discontinued and broken system. It will simply bolt right on to your trailer so it can utilize the 12V power you already have run. It is able to lift 12,000 lbs and lifts 20 inches in 60 seconds. Another great option for you is the Bulldog Square Jack - Drop Leg...
    view full answer...

  • Replacement Boat Trailer Jack Non-Swiveling For Clearance Of HitchMate Boat Trailer Step
  • The HitchMate Boat Trailer Step part # HE4036 should fit with a swing up jack depending on where you place the step. The retracted height of the Fulton Bolt-Thru Swivel Marine Jack - Bolt On - Sidewind part # FXP15L is 26" so you may be able to make both fit depending on where you want the step to be located on your trailer frame. If you still prefer a jack that does not swivel, I recommend Fulton Square, Fixed-Mount Marine Jack - Drop Leg part # FHD2500 which has a 30" Lift and 2,500...
    view full answer...

  • Replacement Gearbox for Ram or etrailer 10,000 lb Square 2-Speed Jack
  • We do in fact have the replacement gearbox you need for the 10,000 lb Square 2-Speed Jack # TJD2SP-12000SP-F. The part you need is the Replacement Gearbox for etrailer and Ram 2-Speed Square Jacks # TJD2SP-12900-GBX.
    view full answer...

  • How to Keep Wheels from Spinning or Slipping on Trailer Valet 5X
  • The Trailer Valet 5X, # STC-V211 is a jack that is mounted to your trailer with a bolt-on bracket and therefore, is designed to be used with just the one trailer to which it is attached. It does not come equipped with the ball base, so a ball cannot be mounted or added to the 5X. The Trailer Valet XL differs from the 5X because it is not a permanent jack, but a trailer dolly which is portable and can be used on multiple trailers. They offer it with a 2" Ball, # TVXL2, or with a 2-1/2"...
    view full answer...

  • Height of Buyers Products A-Frame Jack # 3370091265 without Handle
  • I went out to our warehouse to take a look at the Buyers Products A-Frame Jack # 3370091265 referenced in your question. I measured a height from the mounting bracket up to the top of the tube (before the handle) of just about 9-1/2 inches. I have attached an image to assist. To get the clearance measurement you're needing you likely will need to move down to a 2,000 pound topwind jack (if possible for your trailer's tongue weight). For this I recommend taking a look at the Pro Series...
    view full answer...

  • Bracket to Install Fulton XLT Jack on Mastercraft Boat Trailer
  • The Fulton jack part # F141132 that you referenced is a really great jack that I know you'll be happy with, but it requires the bracket part # P9012-00 to mount to a trailer which isn't the same as what you have now. So your best option is to remove the bracket you have now and install the # P9012-00 and you'd be set. You'd need to find a local welder to have them cut off the old bracket and install the new one. It would be a super painless install for them too.
    view full answer...

  • Replacement Trailer Jack for Viking Legend Pop-Up Camper
  • What you've got there looks like some type of proprietary mount that we don't offer. We do however have jacks that would work. I'd recommend having the mount removed and using a weld-on jack like the Fulton # FXP100W0301 and the # P9012-00 bracket. This is a swivel jack, so when the pop-up is hitched to the tow vehicle, pull the pin and swing up the jack so it stores parallel to the trailer frame. This prevents the caster from hitting anything while towing and getting damaged, which...
    view full answer...

  • Can Electric Trailer A-Frame Jack Be Powered By Power Port in Cargo Area of Tow Vehicle
  • The best way to power an electric A-Frame jack is with a trailer mounted battery and use the 12V accessory power feed from the trailer connector to provide a maintenance charge to the battery. If that isn't possible, the only other acceptable methods would be to tap the jack power wire into the 12V feed from the trailer connector or install a 7-way plug like # A7WCB on the jack power wire and directly use the 7-way on the tow vehicle to power the jack. The 12V accessory socket/power...
    view full answer...

  • What is Difference Between etrailer # TJD-8000S and # TJD-7000S Trailer Jacks
  • The big difference is the orientation of the foot plate on both jacks. One just has the rectangular shaped foot plate rotated 90 degrees from the other. Aside from that they both have the same capacities and travel.
    view full answer...

  • Trailer Jack that Doesnt Hang Down Very Far for a Big Tex Utility Trailer
  • Depending on the capacity you need I do have some A-Frame jack options you might like. Take a look at the Ultimate Trailer Jack # 322-RDJ-2K. It is more adjustable than other jacks and measures just 1-3/4" from the mounting bracket to the bottom of the leg with the jack fully retracted and the collar at the lowest setting. This jack is rated for 2,000 pounds. A wheel or foot will add more to that 1-3/4 inches so keep that in mind. For a wheel you can use # JC-102. For a foot you can...
    view full answer...

  • How To Obtain Replacement Dual Caster Wheels for a Fulton F2 Swing-Up Trailer Jack
  • In order to replace the dual wheels on your Fulton F2 Swing-Up Trailer Jack like part # F1413020134 you can use the Replacement Twin-Track Wheel Kit for Fulton F2 Swing-Up Jacks part # F500130. I know you said you just need the wheels and not the bolt but this is the one way the wheels are offered so you must obtain both these and the bolt whether you choose to replace the bolt or not.
    view full answer...

  • Replacement 500V 30A Fuse for RAM Power Jack
  • We actually carry the replacement fuse part # EJ-FUSE for RAM or etrailer.com trailer jacks, like part # EJ-3520-BBX. With that being said, I have reached out to RAM about this in the past and they have said that there isn't anything special about the fuse so if you are able to find one at your local home improvement store, like one that you mentioned, then it will work just the same.
    view full answer...

  • Trailer Jack to Avoid Tailgate Clearance Issues
  • There are a few solutions for your tailgate to clear the jack on your trailer. I recommend to use a longer ball mount like # D-26, that would move the trailer back further away from the truck and give you clearance you need. If you know what size the hitch on your vehicle is, the rise or drop of the ball mount for your trailer, if you're using weight distribution or not, and the measurement from the center of the hitch pin hole to the center of the ball hole I can make the best recommendation...
    view full answer...

  • Can the Electric Jack w/ Footplate # EJ-3520-BBX be Connected to 12V Circuit on 7-Way
  • You can use the 12V circuit on your 7-Way to power the Electric Jack w/ Footplate # EJ-3520-BBX but it is usually best to use a separate 12V battery that is stored on your trailer. Reason being that sometimes the trailer jack needs more power than the 12V wire from your tow vehicle can deliver. Is it possible, yes, but if that isn't enough power you will need to add a battery to your trailer. We do have the Buyers Products Jack # 3370093500 which you can plug right in to your 7-Way...
    view full answer...

  • Solution for Ram 8000 Series Trailer Jack that Won't Crank Up or Down
  • Sounds like you need a gear kit to fix your Ram 8000 series trailer jack as yours are damaged. For that we have the # TJD-7000S-GR. When the Ram 8000 jack has the issue you described it is due to damaged gears which is what this kit fixes.
    view full answer...

  • Repair Parts for Venture VMC940RB 5th Wheel Landing Gear
  • In case you want to just service your existing Venture VMC940 5th wheel landing gear driver leg you can use gearbox # LG-179015. For a complete replacement lead jack use Replacement Lead Jack with Drop Leg # LG-179013 which is a universal fit that works with major brands. I linked a diagram with measurements so you can compare to yours. For a motor to convert the gearbox and leg to electric operation you can use part # LG-196308.
    view full answer...

  • Comparing Stallion and etrailer.com Drop Leg Stabilizer Jacks for Trailer
  • Quality-wise there isn't much of a difference between the etrailer.com stabilizer jacks part # TJ01RT-HD and the Stallion Stabilizer Jacks # 288-01892-2 that you also mentioned. I'd recommend going with the kit that matches the height requirements you need best. The # 288-01892-2 has a travel of up to 22-1/4 inches and the # TJ01RT-HD has a travel of up to 18 inches. I also attached a review video for these jacks for you to check out as well.
    view full answer...

  • Troubleshooting Manual Adjustment Nut for Lippert Electric Trailer Jack
  • The Lippert Electric Trailer Jack with Footplate - A-Frame - 18" Lift - 3,500 lbs - Black # LC285318 does not yet have a replacement nut available. I reached out to Lippert and they said many people have used impact tools on them instead of the manual handle that comes with it and have damaged that part but they don't yet have a fix for that as it wasn't designed for that use. At this time there is no replacement available, so you would need to replace the entire jack. I've linked the...
    view full answer...

  • Will Stormberg Carlson Electric Jack JET-5000NG Fit with Lippert Jack It Bike Rack Adapter
  • The Stromberg Carlson Electric Trailer Jack part # JET-5000NG will easily fit with the LCI Jack It bike rack adapter part # LC429756 that you referenced. If you check out the picture I attached you can see a Stromberg jack mounted with the Jack It that has same dimensions as this. The jack and Jack It are actually made by same company so they were designed to fit each other basically.
    view full answer...

  • Replacement Manual Jack Handle for RAM Electric A-Frame Jack
  • The correct replacement manual crank handle for the RAM Electric 3,500 Lb Jack part # EJ-3520-BBX is the Replacement Manual Jack Handle for RAM Electric A-Frame Jacks part # EJ-3520-HD.
    view full answer...

  • Replacement Sidewind A-Frame Trailer Jack with 2 Inch Diameter
  • The jack mounts used on a-frame trailers usually follow an industry standard pattern which is a 2-1/4" hole opening and three mounting holes spaced 3" apart. I have attached a photo to show this for you as well. If your trailer coupler does not follow this pattern and you indeed only have a 2" diameter hole to fit the jack through then I recommend using the A-Frame Trailer Jack part # DL22530 which has an outer tube diameter of 2". As long as the tongue weight of your trailer does not...
    view full answer...

  • Trailer Dolly Recommendation for 1,000 lb Boat on Trailer
  • Before swapping out dollies you may want to try to see if putting more tongue weight on your trailer would give you better traction for your Trailer Valet 5X # STC-V211. Since it sounds like you have a bit of weight at the back of the boat it could be that there isn't much pressure on the tires which is why you're having trouble. The only other option, aside from using one of the Trailer Valet remote controls like part # TVRVR3, is to use the manual CE Smith Heavy Duty Trailer Dolly...
    view full answer...

  • What Are The Quietest A-Frame Electric Trailer Jacks
  • There are a number of quiet electric A-frame trailer jacks, although the Stromberg Carlson Electric Trailer Jack # JET-5000 you asked about would not be on the list. That said, you were right on the money with the Bulldog, because their Bulldog Powered Drive Trailer Jack - 22" Lift - 4,000 lbs # BD500199 (Black) or # BD500200 (White) has a powered drive which is going to reduce noise. The other quietest A-frame trailer jack is from Stromberg Carlson, the Stromberg Carlson Electric Trailer...
    view full answer...

  • Replacement Dutton-Lainson Trailer Jack 22457 or 22560
  • I spoke to my contact at Dutton-Lainson and was able to confirm that the Pull Pin, Easy Swivel Trailer Jack with 6" Wheel part # DL22457 for 10" lift or part # DL22560 for 12" lift is a direct replacement for the jack you have on your trailer now. For future reference, the part number of the jack is a set of three digits on the black plastic handle. If you add "22" to these digits that will give you the full part number of the jack. The jack you have now should have either "457" if you...
    view full answer...

  • Mounting Hole Size for A-Frame Trailer Jacks
  • The mounting hole dimensions of A-frame jacks are a standard 3 inches apart on center, so you will need to weld your new jack on. I highly recommend the Bulldog Round, A-Frame Jack # BD1700100317, which has a 5,000 lb capacity and will give you 15" of lift. It has an outer tube diameter of 2-1/4" and sidewind handle; for a footplate you would want # BD018564. This jack has been highly praised by our customers, with nearly 200 reviews it has an average close to 5 out of 5 stars. I've added...
    view full answer...

  • Replacement Foot Needed for a Lippert # 1817941 Electric Jack
  • The Lippert Electric Trailer Jack # LC285318 is the replacement jack for your 1817941 jack and it has a 2" diameter inner tube. This jack uses the Replacement Jack Foot Pad # LC165253 which fits with the 2" diameter inner tube. If your jack has the same inner tube diameter then you want this part number over the part # LC405217 that has a 1-1/2" tube diameter. I have attached a photo with some dimensions listed so you can confirm a fit on your end before purchasing.
    view full answer...

  • Troubleshooting Electric Trailer Jack with 7-Way Plug That Does Not Function Consistently
  • An electric A-frame tongue jack like # EJ-3527-BBX or # 3370093500 that has a pre-wired 7-way plug will rely on the ground and +12V contacts within that plug to deliver operating power. Jacks may not function with less than 12 volts. Those contacts are located, respectively, at the 5:00 and 11:00 positions on the plug as you look at it. Please refer to the linked photo. You might try an aerosol electrical contact cleaner like Caig De-Oxit to see if that restores reliable operation. I...
    view full answer...

  • Replacement Slow Blow Fuse for Ultra-Fab Electric A-Frame Jack 3502 Model
  • The correct replacement slow blow fuse for the Ultra-Fab Electric A-Frame Jack (3502 Model) part # UF38-944017 is the Replacement 30-Amp Slow Blow Fuse part # UF38-751034. Some other parts you may want to keep on hand are the Replacement 20-Amp Auto-Reset Circuit Breaker part # UF38-101238 and the Replacement Toggle Motor Switch part # UF38-75-1037.
    view full answer...

  • Does Trailer Valet TV94FR Trailer Jack Feature a Drop Leg
  • The Trailer Valet # TV94FR trailer jack doesn't feature a drop leg. If you'd be interested in a sidewind jack with a 3K lift capacity, I'd recommend the etrailer branded # TJDA-5000S. The jack offers a total lift of 29 inches. If you'd prefer a top wind jack with a total lift of 28-1/2 inches and a 3K capacity, the Bulldog # BD195318 would be a fine choice. You can view product demonstration videos featuring the # TJDA-5000S and # BD195318 jacks by clicking the provided links.
    view full answer...

  • Can Trailer Valet 5X be Used With a Hitch Ball
  • I can absolutely understand not wanting to buy another dolly, though there simply isn't an adapter or any way to use the Trailer Valet 5X Swivel Jack and Trailer Mover # STC-V211 with a hitch ball. What that means is you will need a new dolly, which depends on the size of your hitch ball: - 1-7/8" Hitch Ball: MaxxTow MaxxHaul Dual Pull Trailer Dolly # MT70881 - 2" Hitch Ball: Trailer Valet XL Trailer Dolly with Chain Drive # TVXL2 - 2-5/16" Hitch Ball: Trailer Valet XL Trailer...
    view full answer...

  • How to Replace Power Switch on RAM Electric Jack w/ Footplate
  • It sounds like you have either the Electric Jack w/ Footplate part # EJ-3520-BBX or the Electric Jack w/ Footplate part # EJ-3520-WBX. If that is the case then the Replacement Power Switch part # EJ-3520-PSW is the correct replacement for you. In order to replace the switch you need to take a flathead screwdriver or pick and pry the top and bottom of the switch to release it from the housing. You can then unplug the spade connectors from the old switch and into the new switch making sure...
    view full answer...

  • Electric Landing Gear Set Needed for Holland Trailer
  • It looks like you have a landing gear set that is similar to the Bulldog 2-Speed Tandem Landing Gear Set # BD500154. I do have a solution for you to have an electric landing gear set but unfortunately we don't have a kit that will fit your landing gear. Instead you will need to replace your current landing gear like the Bulldog 2-Speed Jack # BD183416 and # BD182415. To convert these to electric you then simply need to add the Bulldog Powered-Drive Kit # BD1824180100. These have a weld-on...
    view full answer...

  • Solution for Tailgate That is Hitting A-Frame Jack
  • While your frustration is understandable and we have a solution for you, I wouldn't be able to tell you with absolute certainty that using the Stromberg Carlson Electric Trailer Jack # JET-3755 will stop your tailgate from hitting the jack. The reason is, A-frame jacks like these mount to a specific place on your trailer and if your tailgate comes down at that point, they will hit. What you can do instead is use a side-frame mount jack like the Fulton Marine Jack # HD50000101 or you...
    view full answer...

  • Mounting Hole Pattern of Electric A-Frame Trailer Jack
  • The 3-bolt mounting flange on the Lippert Electric A-Frame Trailer Jack # LC285318 has a standardized hole pattern. This jack is intended to mount so that the included LED light faces forward toward the tow vehicle to illuminate the coupler and hitch ball. In the specs for this jack I saw nothing mentioned about rotating it. Similar electric A-frame jacks like # JET-3755 that also has an LED light built-in use a round mounting flange that has a similar mounting hole pattern. You are...
    view full answer...

  • Replacement Jack for Lippert Electric Ground Control TT Travel Trailer Leveling System
  • I believe the leveIing system you have is the Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System # LC672136, based on the model jack you said it had. I spoke with a representative of Lippert who said that Lippert Electric Trailer Jack # LC285318 can be used as a replacement for the damaged jack from the leveling system; additionally, he told me that you would be able to disconnect the wires from the original jack and re-wire them onto the same location of the...
    view full answer...

  • Recommended Replacement Jack for Shelby Trailer Jack
  • The Fulton Bolt-Thru Swivel Marine Jack # FXP15W is a bolt through replacement option for you. This is designed to use a welded plate like the Jack Mounting Bracket for Fulton Marine Jack # P9012-00. It appears like you have a bolt that goes into a threaded plate, so the reverse of this assembly. If that is the case, I believe this jack will still work, but you will need to put the bolt through the jack first and then thread the bolt once behind the jack into the welded plate.
    view full answer...

  • Replacement Jack for my 2006 Extreme Boat Trailer
  • The Fulton F2 Swing-Up Trailer Jack with Dual 7" Wheels part # F1413100334 that you looked at does not have mounting hardware instead use the Fulton F2 Swing-Up Trailer Jack, Dual 7" Wheels part # F1413020134. It is the exact same jack but includes the u bolt kit you will need to mount it on to the trailer. Check out the video on it that I linked for you.
    view full answer...

  • Availability of 5,000 lb Top Wind Trailer Jack with Grease Zerk Fitting
  • The A-Frame Trailer Jack - Topwind - 5,000 lbs. by Dutton-Lainson # DL22772 does not have a grease zerk fitting integrated, sor do any of our other top wind jacks. This doesn't mean they are difficult to maintain, but they do not have that integrated feature. Normally the bigger square topwind jacks do have that feature like # TJD-7000 as well as some of the side wind Swivel jacks. I've linked the page to all your 5,000 lb Top Wind trailer jack options to assist. You can add the Replacement...
    view full answer...

  • 5,000 lb Bulldog A-Frame Jack With Short Retracted Height
  • I checked and although there is not a bushing for the Bulldog Swivel Jack - Topwind # BD178101, we do have a 5,000 lb Bulldog A-frame jack with a short retracted height that is going to be exactly what you need. The Bulldog Round, A-Frame Jack - Sidewind - 15" Lift - 5,000 lbs # BD1700100317 or the same jack in Zinc # BD1700100301 has an 8-5/8" retracted height, which is the shortest retracted height. These have a 23-5/8" extended height for 15" of lift and you can add a removable foot...
    view full answer...