I just went out to the warehouse and measured the Curt Trailer Hitch Receiver item # C15845. I have attached a couple of diagrams with the dimensions of this hitch on them.
From the center of the back bolt to the front of the receiver is 26"
The crossbeam is 4" X 4"
From the center of the back bolt to the crossbeam is 18" rear 22" front view full answer...
There are a couple of major differences in the 3rd generation Reese Goosebox item # RP85FR over the prior models. First and foremost it now fits the Lippert Rhino pin box. This pin box is more common now than ever and 5th wheel owners will finally have a gooseneck adapter option that will not void their warranty.
Visually the biggest change will be the removal of the taller wings. Reese has changed the angle of the entire goosebox to remove the deeper drop look to a more streamlined appearance.... view full answer...
No, you can't. Those hooks are only for recovery or pulling something they're not rated to be flat towed with. You are actually going to have to remove them to install a base plate kit on your 2023 Ford Bronco.
Since you have a Blue Ox Alpha tow bar you'll want the Blue Ox Base Plate Kit item # BLU23XR. This base plate kit is confirmed to fit the Bronco's with the Ford modular front bumper.
Here are some other parts you will need to flat tow your 2023 Ford Bronco:
Wiring Harness -... view full answer...
I was able to obtain from Curt a chart showing key dimensions for their 3-Piece Trailer Hitch # C15511 (and other hitch models) that I linked for you. This shows that for hitch # C15511 the overall front-to-back length is just under 24-inches. The height from the top of the mount down to the top of the receiver tube is 8-inches. view full answer...
I went out to the warehouse to take some measurements of Curt trailer hitch # C14082. I made a picture showing the measurements for you.
The bolt holes, starting from the one furthest forward on the vehicle, measures 2-3/4 inches to the center of the next hole.
The center of the second hole to the center of the round clearance hole is 2 inches.
And from the center of that round clearance hole to the center of the last hole is 1-5/16 inches.
The crosstube is 2-1/2 inches square.
The... view full answer...
Blue Ox has an easy system for determining the weight capacity of your spring bars, whereas other companies may use measurements or printed capacity to assist. With Blue Ox, there is a 5 dimple system: No dimples means it is rated for up to 350 lbs total tongue weight. One dimple means it is rated for up to 550 lbs. Two dimples indicates up to 750 lbs. Three dimples indicates up to 1,000 lbs. Four dimples indicates up to 1,500 lbs tongue weight. Five dimples indicates up to 2,000 lbs... view full answer...
The height of our RV ladders are calculated by measuring from top to bottom. We offer exterior ladders ranging from 84-1/2" to 99-1/2" tall. However, most of them such as the Stromberg Carlson RV Exterior Ladder part # LA-401 are customizable meaning they can be trimmed to the exact height you need.
The above ladder should work well for you. It is constructed of a lightweight aluminium and comes with all the mounting hardware and brackets you will need for installation. The best feature... view full answer...
The Lippert Electric Tread Lite Step for RVs # LC353543 has a top step that measures 4-1/2 inches from the top of the step to the top of the bracket frame. I confirmed this with my contact at Lippert/HappiJac who makes this step. view full answer...
The Replacement Spring # 4769-28 that you referenced will install onto the pawl assembly of your winch. Check out the pictures I attached that show an exploded diagram to see how it installs. view full answer...
At this point in time we haven't had the chance to install the Yakima LongArm Truck Bed Load Extender # Y01149 on a 2019 Ford Ranger, but we do have some dimensions on it that I think will be useful to you.
If you check out the attached dimensional photo, the second to lowest position has the crossbar 29-3/4" above and 38-3/4" out from the center of the hitch pin hole. The actual pivot motion will be about 12" from the center of the hitch pin hole so you can use all of these to test with... view full answer...
Yes, the B&W Continuum Weight Distribution System item # BW78FR will work with the Gen-Y Torsion 2-Ball Mount item # 325-GH-1226. The Continuum has a tongue weight range of 600 lbs - 1,600 lbs so you will be limited to 1,500 lbs of tongue weight with the Gen-Y Torsion 2-Ball Mount. It tops out at 1,500 lbs and you always want to go off of the lowest rated component. view full answer...
Do you know how much additional clearance you'd need to allow the tailgate to open? 12inches is a longer shank but we might have a slightly longer option. But if you need considerably more length we won't be much help. view full answer...
This is a great question that there isn't exactly a great answer for. Hitch extenders not only put the weight further away from the hitch which would increase the leverage on the hitch, but they also add movement to the assembly which will increase the impact of the tongue weight since there will be play between the hitch and hitch accessory. Think of how a jack hammer works to help visualize what I mean.
I wish there was an exact figure as to how much the tongue weight gets reduced by... view full answer...
The RetraxPRO XR Hard Tonneau Cover w/ Trax Rails - Retractable - Aluminum - Matte # RTT-80384 has a canister that is 13-3/4 inches wide and sits 11-5/8 inches deep from the top of the bed rail. The RetraxPro and the Pace Edwards Jackrabbit # 311-M-JRFA19A45 both have a flush design with the top of your bed rails so the lowest point over your 5th wheel hitch will be about 1-1/2 inches under the bed rail. view full answer...
The air springs included with Air Lift kit # AL57215 are 6 inches tall. Air Lift has this handy graphic, included here, that explains how to measure to determine which size spacer would be needed. However, you pretty much have to have the air spring mounting brackets in place to get the most accurate measurement. view full answer...
This is a really good question. So the Firestone Ride Rite kits like the # F2582 that you referenced are capable of having a capacity of up to 5,000 lbs but the the specific air bags that are used in this kit are only rated for up to 4,800 lbs according to Firestone as the bags this kit comes with are the 267C1.5. If you scroll to page 22 in the attached install instructions for the # F2582 you can see the capacity of the bag pair listed there. view full answer...
The overall length of the seat of Dometic RV Toilet Seat # DOM83FR is 15 inches on the outsides and 11 inches on the inside of the opening. The inner width is then 8 inches. This is a confirmed fit for your Dometic 310 model as well. view full answer...
The B&W Turnoverball Underbed Gooseneck Trailer Hitch, part # BWGNRC816, measures about 15 inches by 13-3/4 inches. It's designed to fit into a custom installation kit that will be specfic for your truck.
If you can tell me the year, make, model, and bed length of your truck I can help you find the correct instalaltion kit. view full answer...
The High Pointe RV Convection Microwave # HP99ZR has a maximum power input of 1,500 watts in both microwave and convection mode. The 1,000 watt rating is the output cooking power provided in microwave mode. view full answer...
Go To Results