The Kat's Heaters Custom Fit Engine Block Heater - Cartridge Style - 120V - 400 Watts # KH11813 is a confirmed fit for your 2008 Scion tC.
To install:
1) Locate cartridge hole on the engine block.
2) Clean cartridge hole of all debris. Use compressed air.
3) Attach cord to heater.
4) Install heater into the hole. Rotate the clip on the cord to the proper position to secure the heater and cord to the engine block and heater.
5) Route the cord through the grill, using cable ties to prevent... view full answer...
I spoke with my contact at Lippert and he informed me that the Center Point part # LC1565391 will support a 21,000 lb trailer. That being said, since you have a triple axle trailer you would want the part # LC1565401 instead. Bag failure is extremely unlikely but if it were to fail you would still be able to travel.
I attached a couple pictures that detail the installation. It basically just replaces you current equalizers and shackles. They attach to your hangers and then directly to... view full answer...
There should be a number on the locking core of your Inno Roof Rack. We have a wide array of keys. If the core matches the key number on our site, that is the one you need!
Here is a list of all the Inno Keys.
T257 # INT257
T282 # INISKT282
T261 # IN74FR
T262 # IN44FR
A76 # INA76
T255 # IN76FR
T253 # INISKT253
266 # IN34FR
T276 # IN84FR view full answer...
We have the perfect rack for carrying your e-bikes with fenders and step through frames! You will want the Thule Easy Fold XT part # TH903202. This rack will fit your 1-1/4 inch hitch, has frame clamps designed for your style of frame, is specifically intended for e-bikes, and comes with ramps to make loading/unloading the heavier bikes (which it is rated for) easier. I attached a picture of the rack carrying a bike just like yours for you to check out as well. view full answer...
The Rhino Rack Vortex Crossbars # RRVA137B-2 you referenced measure 3-1/8" wide x 1-3/16" tall.
The Thule Motion XT Rooftop Cargo Box # TH629806 will fit crossbars that are up to 3-1/2" wide and 1-11/16" tall so they will work on these bars!
If you let me know the year, make and model of your vehicle I can confirm for you which Rhino Rack roof rack will fit and the parts you will need. view full answer...
You can go ahead and direct the photos to me simply by responding to this email. If you could include any potentially relevant measurements I would appreciate that as well. view full answer...
Hey Luke!
On the etrailer scissor jacks # e56VV, the closest bolt holes center-to-center are about 3-1/2" apart, while the next set of holes is 4-1/2" center-to-center. Since yours are currently 80mm apart, that translates to a little less than 3-1/2". If it won't fit right over the studs, you could try to wallow out the holes a little to fit, but keep in mind that would go against instructions and you'd be on your own as far as warranty goes etc.
Other option is to just see if you can... view full answer...
According to the owners manual for your 2009 Scion xD it can only be flat towed with all 4 wheels on the ground if you have a manual transmission. You can dolly tow with either an automatic or manual transmission. So a Tow Dolly # RM-2050-1 is likely going to be what you want. If you have a manual transmission and want to tow all 4 wheels on the ground please let me know and I can list the parts you will need. That install is likely going to require you to go to a local shop to have everything... view full answer...
According to Rhino Rack, the crossbars should be spaced 27-9/16 inches apart, center on center as shown in the provided diagram. Rhino rack chooses the specific mounting points for the crossbars based on where the strongest points of the roof are located. If you were to install the roof rack at a different distance apart, your rack would have an unknown weight capacity which could damage the rack or the vehicle roof if you unintentionally overloaded the rack.
If there was something specific... view full answer...
According to the installation instructions for CURT Trailer Hitch, # 11487, you will not need to remove the muffler in order to install the hitch on your 2005 Scion xB. I have included a link to the installation instructions for you to view.
The hitch comes with a ball mount, hitch pin, and clip. If you plan to do some towing you will need a ball, # 19256 (1-7/8 inch diameter) or # 19258 (2 inch diameter). For trailer wiring, use Curt Wiring Harness, # C56030. I have included a link to... view full answer...
For a muffler, the size of the model that comes with the MagnaFlow exhaust for a 2011 Scion tC measures 5 inches tall, 8 inches wide, and 20 inches long overall with a 14 inch long body. It also has 2-1/4 inch inlet/outlets. A muffler like # MF14235, has these dimensions.
Compare these measurements to what is required on your tC to determine fit. These mufflers are designed as universal fit items. They do make quite a few different sizes but they may not be an exact match. view full answer...
To flat tow your 2012 Scion xB behind an RV you will need the base plates and tow bar like you mentioned as well as safety cables, lighting, and supplemental braking.
For a tow bar compatible with Roadmaster base plates # 1187-1A (with arm height at approximately 13 inches) I recommend the Falcon 2 # RM-520. This tow bar makes hooking up and disconnecting easier when you are not on perfectly level ground or straight. I have linked a video review for you. The video explains how the tow... view full answer...
Yes, the conical tooth washer needs to be positioned so that the teeth face the hitch. That is what prevents it from coming loose. Take a look at the video I have linked. At about the 1:50 mark the installers start to put the hardware on to mount the hitch and they mention the conical tooth washer. view full answer...
I do see your Aventon Level 2 bike has a weight of 54lbs. Since you are using the Curt Receiver # C12490 on your 2013 Scion xB and being a 1-1/4" receiver I recommend the Yakima OnRamp # Y28DJ as it can support bikes up to 66lbs each and has a ramp for ease loading. Using an Adapter # e43YR with the Rack # HLY66ZR not only moves it further back causing more of a lever effect on the weight but do remember the extra length is also going to have an effect on the departure angle which means... view full answer...
The Swagman Chinook 2 Bike Platform Rack # S64683 will fit your Draw-Tite Invisi-Hitch 1-1/4 inch that you have installed on your 2006 Scion xB if you already have the discontinued adapter. If you do not, then you will need to replace your hitch with # C11487.
Some of the Townie Electra cruisers have a very low top tube. If your husband happens to have one of those the adapter bar like part # UB01 would be very helpful to stabilize the ride on your Swagman Chinook rack # S64683. view full answer...
If your 2008 Scion xB has no rails or crossbars I recommend the Rhino-Rack Vortex roof rack system.
This roof rack features the low profile aerodynamic aluminum crossbars with the rubberized Vortex strips in the channel that help disrupt the airflow for a quieter ride. To order this roof rack you will need part # RRVA137B-2, part # RRRLKVA, and part # DK152. If you prefer Black crossbars you can order part # RRVA137B-2.
The bike rack I recommend for this roof rack is the SQR Quick-Release... view full answer...
Hello Joseph, thanks for reaching out. I do have a potential option for you, but I am sorry to say we do not offer a universal air lift kit, and there are no air suspension enhancement products available for the 2008 Scion XD.
One option might be to use the Coil SumoSprings Custom Helper Springs. These insert in the factory coil and help to beef up the rear suspension. I would need you to measure the distance between the rear coils to determine what kit will fit. For example, the oil... view full answer...
Hey Anthony! The difference between the Curt # C59236 and # 56062 is the installation process. The # C59236 is a universal wiring harness that will require splicing. The # 56062 is a custom wiring harness that uses T-connectors for a plug and play installation. Since this will save some money and make the installation easier I recommend the custom wiring harness for your 2008 Scion xB. view full answer...
Like you said you aren't able to carry 3 bikes on a hitch mounted bike rack with your 2006 Scion xB because you need at least a Class II hitch and only Class I hitches are available for your vehicle. So that leaves either the roof or a trunk mount carrier.
If you want to add a roof rack you can use the Rhino-Rack system, parts # RRVA137B-2, # RRRLKVA, and # DK138. Then add 3 bike racks like the TomaHawk, part # RKY1222.
However, I recommend a trunk mount rack. It's a lot less expensive... view full answer...
Yes, you can! I checked with Roadmaster and their Crossbar-Style Base Plate Kit item # 1176-1 is compatible with your 2006 Scion tC with fog lights. The fog lights will have to be removed and not reinstalled. This is detailed in section 6 of the instructions which I have attached below.
I have also linked an installation video. Ours did not have the fog lights to remove though.
Here are some other parts you will need to flat tow your 2006 Scion tC:
Tow Bar and Safety Chains - Roadmaster... view full answer...
Go To Results