Hey Jp, welcome back! Since your trailer has 7,000 lbs underslung axles, you'll want the SumoSprings Trailer Helper Springs w/ Line Relocation Bracket item # SS33HR. This kit is rated for 5,000 lbs - 8,000 lbs axles so it's going to provide way better support than the item # TSS-106-40, you were looking at.
The SumoSprings item # SS33HR are going to work great for reducing trailer sway, absorbing road shock, and they'll also help with that body roll top heavy feeling. These kits are sold... view full answer...
Thanks for the picture of the coupler you have on your military trailer. Based on that I can tell what you have is a Model 6 and the same as the Titan part # T4093200 that you referenced so it would bolt right up. view full answer...
Yes we do!
For the Malone MicroSport Trailer for 2 Heavy Kayaks # MPG461B2, take a look at the:
-Fulton Bolt-Thru Swivel Marine Jack w/ Caster # F77CR.
This jack will work great with your MicroSport trailer, has a heavier duty powder coat to protect the jack from rust and keep the paint fresh, and also has a nice swing up feature that makes this easy to stow when not in use.
Additionally, this jack also has a lift capacity of 1,200lbs, and a maximum lift height of 10".
Attached is... view full answer...
Hey Mitch, the Roadmaster steering stabilizer part # RM38R that you had installed shouldn't have came anywhere near the taillights of the vehicle so if something happened to the taillights I would check with the installer and see if they remember any reason it might have gotten damaged. view full answer...
It seems like you may have the incorrect wiring connector and the harness in the photo is not the correct fit. For your 2015 Lincoln Navigator, the correct wiring adapter is # 22292 for your Tekonsha Prodigy P3 # 90195. If you have the factory 7-way or factory 4-way, this harness will work. The connector will be located in the center of the dash on the driver's side behind a trim panel. I've attached the installation details to assist as well as some videos to help.
The wiring harness... view full answer...
For your 2017 Lincoln Navigator, the towing capacity is rated for 9,000 lbs. That of course is not based on the number of passengers in your vehicle. I looked up your owners manual online and it gave the Gross Combined Weight Ratings, so you simply will check your model with corresponding towing package to get that rating. Then you will subtract the 6,440 from that total to get the complete combined weight your vehicle and trailer can be.
If you will be towing a trailer that is over... view full answer...
Hey Jim, the best option we have for a tow mirror for your 2018 Lincoln Navigator would be the K-Source part # KS3990 which comes with longer straps to fit around the larger mirror housings of your vehicle. There's a lot of adjustability to the clamps/brackets too so it will secure well. view full answer...
Hi Jim; it can be hard to tell but the # RED67CR does include the custom wiring harness for your 2017 Lincoln Navigator. This will allow for a plug and play installation using your factory tow port. view full answer...
Hello Allan; to add a 7-way you need the Universal Installation Kit for Trailer Brake Controller # ETBC7. This kit comes with the adapter, wiring, and everything else required to upgrade your existing 4-way to a 7-way. The # C55774 you were looking at is designed to fit if you have the factory 7-way with a US Car connector.
For the brake controller I recommend the Redarc Tow-Pro Liberty # RED24FR. This brake controller is reliable and easy to use. The main unit installs behind the dash... view full answer...
Hi Mark; the answer to your question really depends on the size of the canoes. The crossbars on the Yakima Rack and Roll Trailer # Y08107 are 78" long. As long as you can fit your canoes on that crossbar size and they don't exceed the 250 lb capacity the answer is yes. view full answer...
No, we do not I am sorry. However, if your 2004 Navigator came from the factory with that 4-Way it'll be pretty easy to add a 7-Way connector. Somewhere close behind where your 4-Way is mounted will be a circular connector called the USCAR. It will look like the connector at the end of the 7-way Curt T-Connector Vehicle Wiring Harness for Factory Tow Package item # C55774. You'll simply be able to disconnect your broken 4-Way and add in this 7-Way connector.
If you do not have this connector,... view full answer...
I drew up a little diagram of how RV water systems are typically designed and attached it below to make it easier for you to see each component. I believe what you're referring to is simply just the fresh water tank drain, which you could use part # CAM22243 to tie into your tank and allow it to drain.
The Anti-Siphon valve # A01-0141VP you were looking at simply connects to a Valterra Hydroflush # F02-4100 for you to hook up a garden hose and clean out your black tank.
For the fresh... view full answer...
Thank you for providing that picture and measurement. Based on what you have there there is definitely enough room to install a weight distribution hitch. I recommend the Fastway e2 which will require placing the brackets 27-30" back along the frame, leaving you with room to spare.
The correct system will depend on the tongue weight of your loaded setup. The best way to find this is to measure with a scale like the # e99044. I have also attached an article below which covers other ways... view full answer...
Since Roadmaster doesn't currently have a baseplate for the 2023 Lincoln Navigator you'll have to use a different branded baseplate and an adapter to connect to your Nighthawk Tow Bar # RM-676. You could use the etrailer Invisible Base Plate Kit # e86YR along with the adapter # e98984.
At this time no manufacturers have been able to confirm if diode kits would be compatible with the factory wiring of the vehicle so all I can recommend is the Heavy Duty Magnetic Tow Lights # TL21RK to... view full answer...
The smaller section of the Z-Rail for Enclosed Trailer # 362417-955 is approximately 3/4" tall, while the larger section is approximately 1-1/4" tall. view full answer...
On your 2020 Lincoln Navigator the brake OEM brake controller wiring is located in the dash near the center console. It will generally be terminated into the dash panel itself where Lincoln would install the factory brake controller. This should be just to the left of your gear selectors.
The brake lights are on a completely different circuit from the trailer brakes. Your trailer brakes will not work without a brake controller.
You will need the Tekonsha Plug-In Wiring Adapter # 22292... view full answer...
We can get your 2011 Lincoln Navigator with the factory 4-way set up with a 7-way and trailer brake controller; and you are correct that a 7-way has a 12 volt pin which allows you to trickle charge an RV battery. So because your '11 Navigator has the factory 4-way, the only thing you need to add for the 7-way is the following part:
- Adapter 4-Pole to 7-Pole and 4-Pole # 37185
With that, the other thing you will need is the brake controller as well as the plug-in adapter, and I recommend... view full answer...
The wheel and tire in the size of 215/60-8 that you referenced like part # AM3H310 are 8 inches wide. For a fender that would be wide enough you would need to go with one like the part # CE17800G which is setup for larger 12 inch wheels. The size of this fender is 27-3/8" Long x 8" wide x 11" tall. So it will be a bit large but it will work.
I attached a review video for this fender for you to check out as well. view full answer...
Yes it is. The Hitch Lock for Kuat Bike Racks - 2" Hitches, part # HL2, will work with the Kuat Transfer V2 Bike Rack for 2 Bikes but not the Kuat Transfer V2 Kuat Transfer V2 Bike Rack for 3 Bikes. The bike racks are secured to the vehicle in different ways, thus the incompatibility. The anti-rattle hitch bolt of the Transfer V2 works like a traditional threaded hitch pin to eliminate the movement between the hitch receiver and the hitch bike rack. The Transfer V3 has an anti-rattle device... view full answer...
Installing the Prodigy P3 part # 90195 is pretty easy on your 2015 Lincoln Navigator. Basically you need to remove a panel on the dash and the connector is there for you to attach to. See attached picture. A mechanic could knock it out really easily but I think you'd have no problem at all. The correct adapter you need is the # 22292. view full answer...
Go To Results