Hey Jacob, sorry for any confusion but the correct trailer wiring kit you need for your 2025 Kia Carnival is the Curt part # CU94FR that you mentioned. The other part number was basically a preorder harness as we anticipated a new part number release but the older part number from 24 Carnival carried over to the 25s. view full answer...
Hi Jerry,
For your 2025 Kia Sorento PHEV you would need the Curt Trailer Hitch Receiver # C37RV for the trailer hitch. The right light kit for your Sorento is going to depend on a few factors. For models with the tow package, like you stated you have, you can install a 7-way connector like the Tekonsha # TK24FR.
Regardless of the tow package you can install a 4-pole connector like the Tekonsha # 118269 (incandescent tail lights) or Curt # C99DR (LED tail lights). The 7-way is really... view full answer...
If you have a variety of older Yakima products that you want to mount to crossbars that are 2-1/2" wide x 3/4" tall then the Universal MightyMounts # Y03590 would be your best bet. These adapters fit a wide variety of Yakima products but they are somewhat specific. If you can let me know what products you are wanting to mount them on I can see about verifying if these will fit or what other parts you may need. view full answer...
Hi Gary; with that 3-bolt pattern you need the # T63FR instead of the # DX83FR. This matches your DICO Aero 6000 measurements which can bee seen in the diagram below. It doesn't show your 2.70" measurement but if you use the good old Pythagorean theorem you can find that that measurement is the same as what you have. view full answer...
That we are Shane! So since you mentioned you have wires behind the driver's side rear tire, that would indicate that you have the factory tow package, so the T-One Vehicle Wiring Harness for Factory Tow Package # 118269 is what you'll want.
Do you already have a trailer hitch as well? If not, I'd recommend adding one with the Curt Trailer Hitch Receiver # C37RV. If you need anything else, please feel free to drop a comment and let me know! view full answer...
To add a 4-way wiring harness for your 2023 Kia Soul, I recommend the Curt T-Connector Vehicle Wiring Harness item # C89KR. This custom fit wiring harness plugs into your Soul's factory wiring harness behind your rear tail lights.
The Curt T-Connector Vehicle Wiring Harness item # C89KR can be used with both LED or incandescent bulbs. This harness uses plug in connectors that eliminate any need to cut or splice wires.
I have attached a picture below, along with an installation video,... view full answer...
The etrailer class 3 hitch # e38KR will indeed fit your 2024 Kia Sportage. We have confirmed with the manufacturer that it will carry over to the 2024 models. Install will be pretty easy, just 3 bolts on each side and no drilling required. You may need to trim a small section of the bumper fascia.
We do offer the Curt wiring harness # C59236 which can be used on your 2024 Sportage. This harness will require cutting and splicing of the vehicles harness. At this time (September 2023) there... view full answer...
Hey Dylan thanks for dropping by! Unfortunately we don't have any videos for the EcoHitch Hidden Trailer Hitch Receiver # EH92KR on a 2025 Kia Carnival, but if you have one and are in the Wentzville area, we'd be happy to install one on your car for free! As long as we can use it for content! If that's something you're interested in, call the customer service line and they can get you set up!
I did go to the manufacturer's website (TorkLift Central) and they do have an installation video... view full answer...
Hey Timothy, this is a great question but what Curt means by vertically in terms of bike racks for the Curt hitch part # C47MJ is a different style of bike rack but I can see the confusion. For example a vertical bike rack is the Yakima HangTight part # Y39GR which I attached a picture of. view full answer...
Yes, there is Jason. We actually have two different options and which one you need is going to depend on whether or not your 2025 Kia Telluride has LED lights. I have listed both of them below:
With LED Lights - Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector item # C29ZV
Without LED Lights - Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector item # C93FV
Both of these custom-fit T-connectors plug into your Kia's wiring harness, which... view full answer...
The door clamp style of roof racks like the Inno part # INB137, # INSUT, and # INK685 do not allow water to leak into the vehicle. If you check out the picture I attached you can see that the clamp actually fits above the door seal. view full answer...
Hey Freddy, that's definitely an interesting situation you've got with the Air Lift 1000 Air Helper Springs for Coil Springs # AL29PD so I did some poking around the internet, and it sounds like it could be a couple of things, but it should be easy enough to check for.
Also, there aren't specific install instructions for the Telluride, all of the AirLift 1000 air bags have the same install process.
So, the first thing that AirLift mentions you check is the air in the bags. If there... view full answer...
Hey Cody, congrats on the new SUV. I've got the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector item # C59236 that is universal so it will fit your 2026 Kia Sportage. It has to be spliced into your existing wiring but it will provide you with a 4-way connector to control your trailer or accessory's lighting functions.
The second option I have is the Curt T-Connector Vehicle Wiring Harness item # C99DR that fit the 2025 Kia Sportage. This custom-fit T-connector plugs... view full answer...
Hey Bill, thanks for reaching out!
Yes, the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector # C59236 will give your 2025 Kia Carnival the 4-Way Flat you need to tow a trailer or use an accessory with lights.
This splices into your vehicle wiring and then pulls power directly from the battery via the 12V lead.
If you don't already have a hitch installed then I also recommend checking out the etrailer # e36KR because it has a matte black finish that does a great job... view full answer...
No, I do not Paul and I doubt Curt or Draw-Tite make anything other than a 4-way for the hybrid model. Aftermarket wiring harnesses for vans are typically limited to 4-way connectors like the item # C63RV for LED lights or the item # C32MJ for incandescent lights. I checked with Curt and these are confirmed to fit the 2025 Kia Carnival Hybrid.
To add a 7-way connector you would also need the Universal Installation Kit item # ETBC7. The kit includes a pre-wired 7- and 4-way trailer connector... view full answer...
To change the 4.80x12 tires on your Karavan 5' x 8' utility trailer to ST175/80D13 tires you will need need to have 5-6" clearance between the top of the tire to the bottom of the fender, and 2-3" between the inside of the tire to the frame.
The ST175/80D13 is going to be about 3-1/2" taller than your current tires, and about 2" wider than your current tires.
Based on the pictures you provided you will likely not have enough clearance without lifting the trailer.
Not to worry this is... view full answer...
Hey Bernadette,
We do have some options for your 2025 Sportage Hybrid!
I spoke with Curt and the Curt Class 3 Hitch # C94WR is compatible with the hybrid model. This is a 2" hitch option with a 525lb tongue weight capacity, great for bike rack usage.
Another option for your hybrid is going to be the EcoHitch # EH82KR. This 2" receiver has a 600lb tongue weight capacity, but what makes it stand out is its hidden design. The receiver tube is removable so when you are not using the hitch... view full answer...
If you are looking for a permanent solution to mount to your 2022 Kia Telluride, the Rhino-Rack RTC-Style Roof Rack Tracks - Channel Mount - 63" Long # RTC16 is a viable solution. We have had neighbors who report that these tracks do flex to fit the contours of their roofs/camper shells. With that factor, you should be fine with mounting the tracks to your 2-inch channel. Also, since the # RTC16 measures 2 inches wide, they will fit the width.
To complete this system, I recommend the following... view full answer...
As you can see in the diagram I provided, the tilt is adjustable up to about 45°. The tilt mechanism has a pin that can be used in two different positions to allow a roughly 15 or 30° degree tilt or the pin can be completely removed for the maximum 45° tilt. If you click the provided link, you can see a product description video. view full answer...
Go To Results