Summer Starts Here - Save up to 70%
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
6,000-lb Capacity. These hollow rubber springs sit above the rear axle to help stabilize and level your Coachmen Freelander Motorhome. They also provide a more comfortable ride by absorbing road shock and improving roll stability. Easy to install and use.
Features:
Specs:
Whether you're hauling heavy loads in your bed or cargo area or you're towing a trailer, you will often see the rear of your vehicle sag while the front end rises. In these cases, the rear axle is handling not only the weight of the cargo, but also more of the vehicle's weight. Because less weight is on the front axle, the front tires are making less contact with the road. Overall handling - traction, steering, and braking - is negatively affected. But the resistance from Timbren's Suspension Enhancement System works with your factory suspension to keep your vehicle level and improve your driving experience.
The Timbren system comes with custom-fit brackets that are bolted onto each frame rail above the rear axle. Hollow rubber springs are bolted to the bottom of the bracket and hang down to where the bottom of the spring sits, 1" above the axle. The inch of clearance allows the existing factory suspension to operate normally under light loads and standard terrain, ensuring the smooth, comfortable ride that you are used to.
Timbren Suspension Enhancement Systems are designed to work progressively. When the hollow rubber springs are compressed, the convoluted design causes them to quickly collapse along the folds. Once the folds are compacted, the stacked barrel shape increases resistance, stiffening the suspension and keeping your vehicle level.
Each hollow rubber spring works independently to support the driver's side or passenger's side of your vehicle. This is helpful when you swerve or make sharp turns. Each spring is activated when it is needed, so body roll is greatly reduced. The independent action also works well when you are hauling off-center loads.
Because the vehicle handles better with the springs, less turbulence will be passed along to the trailer, and this helps to keep the trailer in line. Your driving comfort is further enhanced if the trailer does begin to sway (from a gust of wind or a passing semi), because the movement from the trailer is not transferred to your vehicle. This also works to make the sway subside more quickly.
Another great feature of the rubber construction is that the springs absorb most of the road shock, creating a smoother, more stable ride overall. Wear and tear on the factory suspension is also lessened because the rubber springs work to prevent bottoming out on rough roads.
Timbren's Suspension Enhancement Systems are much easier to install than air springs - there are no air hoses to run, no compressors or gauges to hook up, and no manual adjustments to make. The rubber construction makes Timbren's springs more elastic than similar products constructed of microcellular urethane. And more elasticity allows for a more comfortable ride because the rubber has more travel.
Average Customer Rating: 4.7 out of 5 stars (6000 Customer Reviews)
6,000-lb Capacity. These hollow rubber springs sit above the rear axle to help stabilize and level your vehicle. They also provide a more comfortable ride by absorbing road shock and improving roll stability. Easy to install and use.Great! However…
I installed them on my 2019 Ford E-350 SD Cutaway van, 22’ SRW which I turned into an overlanding rig.
Installation was slow but easy with the chassis jacked up.
It helped to have 15mm and 17mm regular and deep sockets, and a long 17mm open wrench to tighten the rubber bag nut on top for better leverage since it’s a tight space in the C-channel.
Right away I found out that on the passenger side, the brake hose bolted on to the axle was preventing installation of the lower bracket, so I came with a solution which was separating the brake
hose from its nest, by installing 2 aluminum spacers (purchased here on[line] for another project) and an 8mm x 50mm bolt.
Afterwards, I wrapped the brake hoses with Safe-Spirals hose protectors because the hoses may rub on the brackets at some point.
I own an older class C with a Ford chassis. I experienced a lot of sway and lane movement in cross winds.
I installed this kit and it was a game changer. Now it drives like a new pickup. No more worrying about heavy traffic or high winds.
It seemed to give a firmer ride. Not harsh just firm enough to feel solid.
Would definitely not hesitate to use this product again
Well made, with great care given to detail for proper fit. I installed these Jounce Supports on a 1997, E350 Cab & Chassis with fiberglass/aluminum body. When vehicle lowered you can see they already touch on the bottom support (no 1inch gap). Converted to an RV, already heavily weighted. Hopefully once road tested, I will be very pleased.
I know it will be lovely when loaded or the trailer on. However,it rides like a wagon empty with brand new premium shocks and struts empty. Thud thud thud. You really cannot feel the shocks or suspension. Found exact same item plentiful for 60 bucks on eBay after I bought these for 250. I may cut these in half or put air bag on. I do not like the ride empty. No hard feelings. It is a good product maybe just not for me.
About a 1/2 inch difference in gap at the bump stop perch but still within parameters. Truck sits perfect with trailer attached. Haven’t towed yet. After towing if they perform like they should will upgrade to a 5 star. Easy to install, definitely needed 2x4 and jack. 2011 Silverado ext cab with 30 ft Genisis 5th wheel.
Was able to install these with a 15mm flex head ratchet wrench and lifted the rear of the truck to make it easier. 30 minutes to take off 4 nuts and put em back on. 2 minutes assembling the timbrens with the added spacer. I have a f350 with a salter and plow. Loaded with salt the lights shoot up and in the snow ?? it’s like hitting hyper drive and you’re blinded. These helped big time. Very happy so far.
The pro: The longer, heavier bump stops worked great when hauling my mustang home from Chicago. The truck stayed level and handled great.
The con: I had to remove the bump stops for everyday use. They limited my suspension travel causing a stiffer ride.
I am so glad I bought these for my truck. I was able to install them myself using a jack and jackstands. The ride is bit rougher now; but the suspension is totally awesome compared to before. I am able to haul a bit more weight when needed.
Haven’t had it on long, but so far so good. 1999 F350 dually. Bolted up nicely. Total job took 10 minutes. Have hauled two gooseneck loads of hay and truck drives SO much better. Nice and level. Money well spent so far.
very good product ,received just in time and fit perfectly on my GMC savana 2000 .Be sure to clean the two receptacle thats help.
très bon produit , reçu dans les délais et s'ajuste parfaitement . Assurez-vous de nettoyer le receptacle cela facilite l'installation.
The timbrens actually did what they were suppose to do. However, once I starter driving out west I notice the timbrens were riding on the axle which cause the speedometer to jump around depending on the road. I would recommend them if you are hauling or towing a camper or RV. I was going to contact etrailer about maybe removing a spacer for one set however the other set came as one unit. The bottom line is the Timbrens does stabilize your load for safe travels. I will be contacting etrailer soon to assist in correcting the problem...Road trip from Idaho,Colorado,Wyoming,and Utah were beautiful... Thank you etrailer
Definitely a must have when towing..stiff without a load but night and day difference while towing my travel trailer, better traction, steering and braking. Easy quick install..only issue I had was with the long bolts they sent with the spacer kit (optional for lift) the bolt diameter was too wide to fit through the holes on the bracket..but a trip to the local hardware store took care of that.
Pros: Cheaper and easier to install than airbags, do the job when load is enough to compress the shock, with added weight or towing, then it stiffens the rear very nicely.
Cons: Doesn't do anything until there is 2-3cm of compressed shock. It sits above the contact point, doesn't touch. Under normal driving, there is no benefit/improved stiffness/anti sway in rear or a leveling of the factory rear sag in a 2022 or newer Toyota Tundra.
If had it to do over, would have put some kind of spacer in between product and upper included bracket, the supplied bolt is long enough to accommodate, to eliminate the gap, and lift the rear 1-2 cm. Should do it anyway, maybe when swapping to summer wheels next month.
I’d seen similar products rated in the 4,000 lb ratings but I went with these. I’m not a mechanic but I removed the factory bump stops and installed both these in 30 minutes or less. I used my rolling jack and lifted from the drop hitch and easily removed the old ones and soapy water and 1/4 twist and these were on. Placed a block of wood in the space between these coils and lowered the jacks then pressed it with my tractor to confirm full engagement. I carry a lot of tools on a 2020 Chevy 2500 I do feel a bit of butt bounce on large bumps but other than that I’m very pleased.
The order with Will at etrailer was great. He was very helpful and knowledgeable, Installation was not easy but not too bad, The hardest part was removing the factory pieces I removed them from below which was a blind nut removal operation. This is on a 2017 Mercedes Sprinter motorhome. After removal of the factory pieces I discovered that access is much easier on top between the tire and the mud flap, I turned the front wheels inward and they didn't have to be removed. The front of the motorhome had to be raised quite a bit to get the Timbren piece jnserted. Also I learned to tighten the bolt and nut in the Timbren bumper as much as possible before installation because there is no access to the bolt head when tightening the top nut to keep the bolt from turning, preventing tightening the nut.
First off the product was beat up with paint/power coating missing in several places on both. I was putting on a brand new truck with less than 800 miles on it so I elected to touch up before install. I’ve hear a lot about Timbren but never had them. I had airbags on my F350 but when I switched to a new Tundra I went with Timbrens. I’m a bit disappointed in the ride. Feels like I can feel a “bump” in the truck from the rubber pick hitting the axle when I go on a bumpy road. Thinking I should have went with airbags. As far as having a load on the truck and helping with the squat, they do as they are advertised.
I bought these to prevent the "squat" of carrying a load in a Ram 1500.It took only 30 minutes to install. Now when carrying a load or towing a travel trailer the truck is a better position.
The only thing you will notice is the smoothness of the ride. It's not, it is stiff. I'd rather have the stiff than the nose pointing to the moon.
They do exactly what I wanted them to do. They support my boat trailer and when not towing, they don’t touch the bumpers everything’s great.
These work great for giving you a solid towing experience when loaded heavy; however, when driving empty you definitely get the jounce bumper “into the air” experience when driving on moderate to rough roads. I have the recommended gap installed between the axle and the timbrens, but with terrible midwest roads and highways it doesn’t seem to be enough gap. Smooth roads it rides great. It’s driving 80mph on the expressway and hitting potholes or large cracks where these will hit causing uncomfortable harsh ride.
I’ve resorted to installing and then subsequently removing these anytime I use my travel trailer for longer trips (30minute removal time). I tow a 7000lb loaded travel trailer with an f150 and just needed something to make the soft half ton suspension from porpoising too much on bad-roads. Mission accomplished when towing as I said these things work great for heavy loads. It almost rides better with heavy loads…. I was going to give airbags a try but the reviews from others have scared me from those because even with airbags at the lowest setting you still get the jouncing on bumpy roads.
Easy install took about 20 minutes on my 2017 Ram 3500 SRW. Had about 1/2 inch clearance as recommended. Loaded up my 5th wheel (2350 hitch weight) and about 200 lbs of gear in the bed. Just got back from a 800 mile camping trip through mountains of TN. You can really feel the difference around those sharp corners and uneven surfaces. The truck felt firm and controlled not hard and jarring as some have mentioned. Going over those overpasses with the wonderfully smooth (Not) joists was greatly improved. The truck would squat and rebound again, with a firm controlled response. Driving without a load felt the same as before without them. I would highly recommend these! Ordering from etrailer continues to be my go to option!
So just got them installed today 3/27/24 haven't hooked up the 5th wheel yet but will be this weekend so we'll find out if they are good as everyone claims they are fingers crossed. Install was crazy simple took about 30min(had to find a wrench) have about 1/2in gap between the axle, really excited to test them. Will update the review after this weekend.
Installed these Timbrens on my 2016 F350 to enhance the stability of my truck for a slide in truck camper. Have loved the results of them. They have noticeably helped leveling the truck/camper combo, and sway while driving. When the camper is off the truck these are not engaged. Have had no issues and would recommend them.
The Timbren rear bump stops for 2020 Suburban were great quality and fit perfectly in the replacement of the original ones with no problems. The old ones pulled right out by hand with no hassle. When I installed the new ones I put 2x4 blocks that I cut underneath the bump stops. Then hooked up the 6,400 lbs travel trailer with about 750 lbs of tongue weight on it and they pressed right into place. The Suburban was more stable because it had less swaying while towing. I also gained about 1 inche more in the fender gap which means less rearend saging.
ordered over the phone and got a very nice lady that was very helpful. was feeling like crap so took a few days to open box up and found out only half was there no bolts only one top mounting piece and only one rubber spring part. but i got two big rubber washer things
Do you have a question about this Vehicle Suspension?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.