8-5/8" x 2-7/8". Waterproof trailer light acts as brake, tail, turn, side marker, side reflex reflector, rear clearance, rear reflex reflector, license plate. ONE Series provides bright light using fewer diodes than other LEDs. Stud mount.
Features:
Specs:
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The circuit board is sealed, which means that water will not damage the diodes or circuit board.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today we're going to take a look at and show you how to install the Optronics ONE LED Trailer Light. This is the driver's side eight function light. Part number is STL0017RV. For the passenger side you'll need the seven function, which is part number STL0016RV.The ONE LED Trailer Light is completely submersible so they're going to work out really well on the boat trailers, and the LED configuration's going to draw a lot less power than what we typically get with the incandescent style light. It's been designed to give you your running light signal, brake and turn signal. On the driver's side that will also include the license plate light on the bottom to keep you compliant with state laws.
The light also uses surface mount technology for its LEDs. That tends to be a more rugged and durable system, so we won't have to worry about failure. The light's also DOT compliant so it can be used in any application.To install the light, we just want to make sure we pre-run our wires. You can see we've got little keepers there to help hold the wires in place. I really think that's nice.
It keeps them tucked in so we won't have to worry about smashing them. Also, we have options in the mounting locations. You can see there's three areas here. Some will use the wider, and some are going to use the narrower so you just want to pick the one that matches yours. Ours happens to be the narrower one.
So just pull that off. You can see the ring terminal on our ground. We've put that right on that stud. When we sandwich it together, we'll have good ground contact.We can line the bolts up with the holes on our trailer, and you can see we've got our serrated lock nuts we'll thread on the back side. And then we'll use our 7/16 inch socket, and we can get those tightened down.On the passenger side, typically, not all situations, but typically your brown wire's your running light, and your green wire is going to be your turn and brake.
If yours is that color, just match them up. We're going to need some butt connectors to put these together. Since this is a marine application, we're going to go with heat shrink. This is part number DW05744. You just want to slide that on and get it crimped down. So that connection's made, we'll just slide our butt connector under our other wire and crimp it down as well. If yours don't match the standard trailer colors, then just test them out with a test light to make sure you've got the right wire that you're connecting to. Give it a pull, make sure it's nice and secure and do the same thing for the brown wire.On the driver's side, this green wire is typically yellow. Everything as far as the installation is going to be identical with the exception of that wire color. Now we'll use a heat source. You can use a mini torch, a heat gun or a lighter. Just gently apply heat and get those shrank down. This is going to create a watertight connection so we won't have to worry about corrosion. Now we can just use a couple of zip ties. We want to keep our wires up nice and tidy just to reduce the risk of them getting hung up on anything and getting pulled.Now to test it out we'll start by turning on the running lights. Let's check our turn signal, our brake lights. And that's going to complete our look at the Optronics ONE LED Trailer Lights.
Average Customer Rating: 4.8 out of 5 stars (504 Customer Reviews)
8-5/8" x 2-7/8". Waterproof trailer light acts as brake, tail, turn, side marker, side reflex reflector, rear clearance, rear reflex reflector, license plate. ONE Series provides bright light using fewer diodes than other LEDs. Stud mount.Good products fairly priced will buy from them again
Fast shipping, no issues whatsoever
This light was easy to mount in the existing holes in my boat trailer. . It took longer to remove the old one than it did to mount the new one. I will be replacing the one on the other side because the new one is so much brighter. Great service, and my light was delivered on the projected day.
The tail lights are an exact match, wire color and mounting bolts, to the original tail lights I am removing. Easy to install. Good thing because the instructions are not available. I am very pleased with the purchase of these LED tail lights.
Excellent experience. Rose helped me select exactly the right item. Arrived sooner than promised and installed in just a few minutes. Now I know exactly where to go for trailer lighting parts.
Arrived sooner then I expected and packed very well. My only negative is I wish on the web page the descriptions matched better when it comes to buying a pair of lights (driver vs passenger) when the description doesn't match it makes it harder to the matching light, but customer service was very nice and figured it out for me. So I suggest if your not sure don't hesitate to call them and let them figure it out.
Exact replacement. Arrived a day early.
Amazing product always works superbright easyily installed. Love this product
shipped fast and was just what I needed....the new lights are bright and easy to install...perfect...
Quick shipping, great price!!
Review from a similar ONE in Trailer Lights
I couldn’t find anyone that had the tail light I needed for my trailer.after looking at every place I could find I finally looked on etrailer web site and found what I needed. I called and spoke with the representative to make sure it was the right one. The representative was very helpful and determined it was the right part. The part actually got delivered quite a bit faster than expected. Thank you
Review from a similar ONE in Trailer Lights
Product and service brilliant. One the big things in service have been sorted, eg. good product, value for money (not cheapest) delivered in good condition in a predicted timeframe, it's the little things like an email with tracking url that has ALL the information you need... WITHOUT HAVE TO TYPE IN A TRACKING NUMBER , NAME, ZIP ETC. And same with review, click on a url in an email and enter your comments with pictures .....SIMPLE. so many other companies just make these types of things too complicated and onerous for the customer to provide feedback. Also each person in the process is named! Brilliant, personal and just nice. I wish you guys were responsible for all of my transactions for all the things I buy online. Thank you to all of you at etrailer fantastic job.
Review from a similar ONE in Trailer Lights
Terrific upgrade in my opinion. The installation was pretty easy for me. The light is slightly smaller than the original and I have the corrugated sheet metal siding I did not experience any led hyper flash with this light. I was slightly concerned about this after seeing videos of people changing to led light bulbs on the tow vehicle. This light was plug and play. 4 stars because the manufacturer did not provide a wiring diagram :( I don’t feel you should guess what wire goes where. The least they could do is tell you what they (the manufacturer) wired for ground. In my case, the white was ground, same as my trailer wiring. However I needed to connect green to black to get my turn signal to work. Your situation may be different. Would I buy it again? At this time, yes. I’m hoping this light outlasts my usage of this travel trailer- which should be for many years.
Review from a similar ONE in Trailer Lights
These were a perfect fit on my 2018 Tracker Boat trailer. Had the same plug in receptacle and bolt pattern. Very pleased!
Review from a similar ONE in Trailer Lights
They work. Question is for how long? Submersible tail lights don't seem to last too many years.
Review from a similar ONE in Trailer Lights
So, I rewired my trailer to not have any wiring connections underwater during a launch operation. To accomplish this, I placed the "etrailer" tail lights and brackets on existing guideposts, then using two "shielded electrical extension cords" I routed them from the tail lights to the trailer hitch plug-in connector.
Review from a similar ONE in Trailer Lights
So, I rewired my trailer to not have any wiring connections underwater during a launch operation. To accomplish this, I placed the "etrailer" tail lights and brackets on existing guideposts, then using two "shielded electrical extension cords" I routed them from the tail lights to the trailer hitch plug-in connector.
Review from a similar ONE in Trailer Lights
Matches my stock taillight to bass tracker classic xl trailer. perfect match harness hooks right up.
Review from a similar ONE in Trailer Lights
So i have a 94 Jayco pop up that one of the tail lights got smashed. The company that made those lights is no longer around. After some searching on etrailer.com I decided on these LED lights. Price was right. My only real complaint is that these lights come with nothing. No screws, no instructions, no seals. So when I pulled my old lights and found that they had 4 wires and these lights had 3, time to do some research. None of the wire colors matched up. Not the trailer wires, not the old lights etc. On etrailer there is a video describing the lights in detail. Watch it. He goes over what color wire does what on the new light. I hooked the trailer up to the car to figure out the old lights wiring scheme. I was able to figure it out from there, though you cannot wire both sides up the same, if you do when you put the turn singles on they both flash. I had to leave the brake light wire disconnected on one side. Brake lights still work without it. I used plumbers putty to create a seal. That is also what they used on the originals and I used the original screws to make new holes and mount the lights. All in all it worked out but instructions would have been greatly appreciated!. I am sure etrailer would have jumped in to assist if I asked but it was not needed. Pictures posted. Old lights on bumper for reference.
Review from a similar ONE in Trailer Lights
So i have a 94 Jayco pop up that one of the tail lights got smashed. The company that made those lights is no longer around. After some searching on etrailer.com I decided on these LED lights. Price was right. My only real complaint is that these lights come with nothing. No screws, no instructions, no seals. So when I pulled my old lights and found that they had 4 wires and these lights had 3, time to do some research. None of the wire colors matched up. Not the trailer wires, not the old lights etc. On etrailer there is a video describing the lights in detail. Watch it. He goes over what color wire does what on the new light. I hooked the trailer up to the car to figure out the old lights wiring scheme. I was able to figure it out from there, though you cannot wire both sides up the same, if you do when you put the turn singles on they both flash. I had to leave the brake light wire disconnected on one side. Brake lights still work without it. I used plumbers putty to create a seal. That is also what they used on the originals and I used the original screws to make new holes and mount the lights. All in all it worked out but instructions would have been greatly appreciated!. I am sure etrailer would have jumped in to assist if I asked but it was not needed. Pictures posted. Old lights on bumper for reference.
Review from a similar ONE in Trailer Lights
These lights were an exact match to my previous lights. They were trouble free to install, though they could use a couple more inches of lead wire in my opinion. That wouldn't prevent me from buying them again. etrailer is among the best online retailers I've ever used. They provide the end user with lot's of product information as well as great installation instructions and videos. You know both what you're getting AND how to install it.
Review from a similar ONE in Trailer Lights
So simple to hookup! I smashed the driver side rear light when a tie-down snapped and my dirt bike fell on it. First day of a 2 week vacation. The next day I got online and ordered LED replacements for both side. I wasn't sure about how long it would take, and unfortunately etrailer doesn't provide any information about shipping times for the various options. I ordered it with USPS delivery to the house we are renting on a lake. I thought it might take 4 or 5 days. Boy was I surprised when I got an email for USPS saying they couldn't find my name or address and had sent it back. The name I could understand, but the address? I have received many packages at this address over the years. I even Googled it and it showed up just fine. The day before I received another package. SO no I was concerned that I couldn't get it in time to replace before we left for home. I discussed my problem with George. He checked the tracking info and confirmed the parts were on their way back, so he reordered and suggested we just use Ground. I mentioned to him that I was nervous about the time, and before I could call (to early in the morning) I had gone on another online retailer knowing they could deliver to this address. I was surprised to find the exact same pair of lights, both cheaper and free delivery. George said etrailer had a price matching program, and if I could send him the other online retailer info he would refund the difference. The parts arrived right about the time I was told, and it took me perhaps 30 minutes to rewire and test. Nice bright lights, much better than the original. Thank you once again etrailer, I love your company!
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.