This waterproof identification light bar with 9-LED lights is 17-5/16" long and designed for trailers wider than 80". Surface mounts to trailer - hardware not included. 2-Wire design with 0.180 female barrels. DOT approved.
Features:
Specs:
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The housing and lens are sonically sealed together to create a single unit, which means that water will not get into the light and damage the diodes or circuit board.
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
Surface-mount lights install flat against the surface of the trailer, so a hole does not need to be cut into the trailer for the light. This type of light is installed using a flange or bracket that has mounting holes. And mounting hardware is used to secure the light to the trailer.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today we're gonna take a look at the Optronics Identification Light Bar for trailers over 80 inches wide. This is going to be a waterproof light that's going to be designed for trailers that again are wider than 80 inches. This is going to surface mount to your trailer. It has two holes on either side so you can bolt that into place. This is going to be DOT approved and it functions as an identification light with those three Optronics MCL 14 Series Lights. These are replaceable using part number MCL14RGB, which are sold separately.
There going to be sonically sealed and they're gonna have a waterproof housing and lens. There's durable surface mount technology construction so the LED's are gonna be able to better withstand shock and vibration as well as they're going to have improved heat distribution so you don't have to worry about these wearing out, even if we're going over uneven terrain or pavement. They're gonna stand up to a lot of abuse that way.And of course LED's are always gonna be a great replacement for incandescent lights since they last up to 50 times longer, they're more efficient, provide brighter light with less power output and there's no bulbs to replace. You don't have to worry about any brittle filaments busting on you and then you have to replace that bulb and get in there and rewire everything. This is gonna be a really durable long lasting light.
It's gonna have those two leads. We're gonna have our black wire for power, white wire for ground. If we turn on our power here, you'll see just how bright that light is. Let me turn out the lights in the studio so you can get a better idea how much that illuminates. So as you can see it's gonna be a nice bright red light on the back of your trailer.As far as the dimensions, this is going to be 17 and five 16ths of an inch long by 1 and a quarter of an inch tall and about 15 16ths deep.
So if you turn this sideways it's gonna be just under an inch deep. The lead wire length coming off the back, it's gonna be about seven inches. So if we undo our alligator clips there, that wire coming off the back is seven inches so that should give you plenty of wire to get this connected. It does come with pre attached connectors on the end there so you can plug those right into your light wiring or cut these off and strip them and use either a butt connector or heat shrink or something to get that all connected correctly. There is going to be a lifetime warranty on those LED's and the power draw for this is going to be one, or point one four seven amps at 12 point eight volts DC.And that's gonna do it for our look at the Optronics Identification Light Bar for trailers over 80 inches wide..
Average Customer Rating: 4.8 out of 5 stars (720 Customer Reviews)
This waterproof identification light bar with 9-LED lights is 17-5/16" long and designed for trailers wider than 80". Surface mounts to trailer - hardware not included. 2-Wire design with 0.180 female barrels. DOT approved.Easy to install works and looks great!
Just what I needed.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.