A complete axle assembly isn't always the answer. Start with this beam-only trailer axle and build the setup that fits your trailer. Add the components you need, then keep routine bearing maintenance simple with Super Lube spindles.
Replacing an axle doesn't always mean replacing every component. This beam-only axle gives you the axle and straight spindles while letting you choose compatible hubs, brakes, springs, and other components (sold separately). Whether you're replacing damaged running gear or building a trailer from the ground up, you can finish the assembly with the components that work with your trailer.
Routine bearing service takes less work with Super Lube spindles. A grease zerk in the end of each spindle works with a dust cap that has a removable rubber plug, letting you add fresh grease through the spindle instead of removing the hubs for routine lubrication.
This overslung axle positions the leaf springs above the axle, raising the trailer compared to an underslung configuration. It's the right choice when you're replacing an existing overslung axle or building a trailer that needs additional ground clearance.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi, everyone. Steve here with etrailer. Today we're taking a look at the Lippert trailer axle beam with super lube spindles. So folks, maybe you have a damaged axle or you're building a trailer from the ground up. Maybe you already have hubs and stuff you want to reuse, but you just need the axle beam with the spindles. This is a great option for you.
Now this axle is rated for applications between 2,500 up to 3,500 pounds and it's set up for an overslung suspension. What do I mean by that My seats, my spring seats are welded on the top. My springs are going to go on top of the axle, which is going to raise my trailer up, give me some additional ground clearance below. Now, one of the features that makes these nice is that these are super lube spindles. What's that mean There's a grease circuit right here on the end of this spindle where I can just pump in grease whenever it comes time for maintenance and just re-making sure everything's good to go.
These are my spring seats. Obviously this is my spindle end here. Now they do come like this with some grease put on there. It's really just to keep these protected during shipping. I would not recommend using this grease, meaning when you get this, wipe this clean, use some brake cleaning stuff after you wipe it up as much as you can, get it really clean and dry because you don't know if there's any little specs of sand or anything like that.
All that could potentially hurt your new bearings and stuff that you're putting on. So wipe all that off, start with fresh grease. Plus you want to make sure the grease that you're using matches 100% through everything. Never mix your greases. It is set up for a break, so it's got a four bolt flange here.
So that's going to be about a 10 inch by two and a quarter inch brake and hub assembly. So you can build that out with parts sold separately if you don't already have those. And then of course you got your wire already ran through the beam from the manufacturer. So this is your brake wire already here ready to go on both sides. So I talked about the spring seats being over slung. As far as the measurements, when you measure to match up to replace an axle, the center of a spring seat to the center of the spring seat, that's one crucial measurement. On this particular axle, it's going to be 65 and a half. Sorry, 68 and a half inches, spring center to spring enter. And the hub face or wheel, where the wheel sits flush on the hub, that hub face measurement on this axle is going to be 85 inches, hub face to hub face. The overall length of the axle is going to be a little bit longer than that, but this is considered an 85 inch axle because of that hub face. That information is also usually on the manufacturer sticker. If you're fortunate enough this sticker survived the last few years of using it, then you might have that information on there. Some of the new axles nowadays are getting laser edged on them as well, so you might have that information on there as well. But again, it's very crucial that you match up those two numbers exactly the same if you're replacing an axle for an axle. Now, if you're customizing everything, you can probably make whatever you get work based on what you know you need. That's totally fine. Well, folks, that's going to wrap up our quick look together at this Lippert trailer axle beam. Again, 85 inch hub face, 68 and a half spring center. I'm Steven, thanks for watching.
Ratings & Reviews
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.





Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.