To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
If you like a clean, factory look when you’re not towing, this kit delivers. The hidden bracket design keeps the setup virtually invisible once the drawbars are removed. The brackets are mounted within the grille where they stay protected from scrapes and scuffs, so you won’t have bulky steel hanging out front.
No fumbling with pins or clips here. Each removable drawbar simply inserts into the bracket, twists to lock, and you’re ready to roll. When it’s time to disconnect, just twist and pull them back out. The twist-lock attachment keeps things simple and reliable for anyone who likes a quick setup before hitting the road.
This isn’t light sheet metal—it’s built from computer-cut, all-steel components that give exceptional strength where it matters most. The black powder coat finish adds durability and corrosion resistance so it stays solid and good-looking for years of towing.
There’s no welding required to get this base plate on your vehicle. The custom design ensures a perfect fit to the frame, and all mounting hardware and instructions come in the box. It’s a straightforward job that gives you solid attachment points ready for your tow bar setup.
If you’re running a Roadmaster system that uses a quick-disconnect crossbar, this kit works right with it when paired with part number 910021-00 (sold separately). That means you can stay within your existing setup without having to swap out your tow bar or major components.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Shane: Hi, I'm Shane with etrailer.com. Today, I'm going to walk you through how to install Roadmaster's Crossbar-Style Base Plate on your 2017 Ford Taurus. Adding the base plate to your vehicle, is going to allow you to flat tow your vehicle behind your motorhome. It's going to make it a lot easier when you get to your campsite, because you can leave your RV set up. You're going to have another vehicle to go exploring or go to the store. It's going to be one of six components required to flat tow the vehicle.Our base plate is going to attach to the chassis of the vehicle to give us a solid attachment point for our tow bar.
Our tow bar is going to give us that solid connection point between our base plate on our vehicle and our motorhome. Our safety cables are going to be a secondary safety device in case our tow bar fails. Our braking system is going to allow our vehicle to not only slow but stop itself, so we don't have to rely on motorhome's brakes to stop and slow both vehicles. Our wiring, that's going to allow our vehicle, while it's being flat towed, to receive light functions from the motorhome, so that not only we're safe, but other motorists are safe, because they're going to be able to see what we're doing, whether that's breaking, turning, or driving at night.There is one more component that may or may not be needed depending on the height of the back of your RV, and that's a high-low adapter. Our base plate on our Ford Taurus sits at 14-1/4".
What you're going to need to do is you're going to need to go out to your motorhome, and you're going to measure from the ground to the center of your hitch. If those two numbers are within 3", you're good. If they're not, and they're over 3", you're going to need a high-low adapter to make up that difference. The reason you need a high-low adapter or that angle to be within 3" is because we want our tow bar to be as straight as possible when we're flat towing our vehicle.Our Roadmaster Crossbar-Style Base Plate is really going to work well for flat towing your Ford Taurus behind your motorhome. It's going to hold up well.
It's going to be steel construction, black-powder-coat finish. It's also going to have removable arms to help maintain a really nice, clean look on the vehicle To take them off, you simply twist them and slide them out. You can see there's not a whole lot sticking out. Again, maintains a nice, clean look on the front of the vehicle. Insert it, you have a tab here that's going to fit on the bottom side of this tab on the base plate itself, so you simply slide it in and rotate it.This bracket here on the front, this doesn't actually come with the base plate.
It actually comes with the tow bar. But if you notice this plate on here, this bracket is flat, and it requires a tow bar that has the quick-disconnect bar, which is part of this plate here. What that is is when you mount these on, it's a bar that connects onto your tow bar, and you just slide it into place and pin it at the top.The plates that are mounted on here are for a cross bar like this. It's for an easy disconnect. It slides on just like this onto the base plate, and it's going to have a pin that slides in the top to hold it on. Then when you put your tow bar on, your tow bar is actually going to hook in right here. Once you get that connected, you can just take out these pins and slide this whole bar off, and it'll stay right on your tow bar. Keep in mind with doing that, if you plan on storing your tow bar on the back of your motorhome, this bar is going to spread those arms out about this far, so just keep that in mind. You will have to find somewhere to store this if you decided to take it off the tow bar itself.A great tow bar to work well with this base plate is going to be Roadmaster's Falcon All Terrain. It's going to come with the quick-disconnect bar. It's going to come with the brackets to mount on the removal arms. You can find that tow bar here at etrailer.com.Now when comparing this base plate to other options for the Taurus, I think this is going to be the best option. The connection between your tow bar and the base plate itself, I think it's really solid. I think the arms that go inside the base plate give it a really solid foundation for the tow bar. Some of the other ones, they have smaller arms on them, and the tow bars, the way they connect on there, they're just really loose, and I don't think it's a real good connection between the two. I think this is going to be the best option here.To start our installation, we're going to remove our fascia. We're going to start underneath our hood. We're going to have four, 10mm-head bolts and two push-pin fasteners we need to remove. For the push-pin fasteners, you want to get to under . See where that little opening is, top of the center and then the base.And then each wheel well, we're going to take a 5.5mm socket. You're going to have one, two, three bolts to remove. Take an 8mm socket. This bolt right here, we need to remove. Right up here in the corner, there's going to be a plastic fastener. This one can be a little bit of a pain to get out. Take a Phillips screwdriver, and you just want to turn the center. You don't have to put any pressure on it, and hopefully the center comes out. If it doesn't, take a pick or something like this, and what you're going to do is you're going to put a little bit of pressure. Get underneath the head, kind of like that, put a little bit of downward pressure on it. Then take your Phillips screwdriver. Then just turn the center. Just like that. And then we need to get up, and we need to pull the base out. You can do the same thing. If you don't have a pick like this, you can use a little, flathead screwdriver. Just like that. We're going to do that same thing to the other side.Then we're going to have five of the same fasteners attaching the splash shield to the sub-frame. They're right down here underneath. This one looks like it's loose. Then we're going to have a fastener like this or a plug on each side for our fog lights, if you have them. You want to make sure that you unplug those.Now we want to start on the outside and work our way to the center. It's a good idea, if you have a second person that can help you, go ahead and do it. Even though the fascia's not hard, it's a little awkward to go from here over to one side. We're just going to pull out. The top of this is going to be kind of clipped into place. We just want to lift as we're pulling it off. You want to make sure that you don't just pull your fascia off. Check for any wiring that may still be hooked up, and you want to make sure you unhook that so you don't damage the fasteners. Now we'll take this and set it aside somewhere safe.If you have louvers, on the backside you're going to have a louver alignment bar that has three fasteners on it. What we're going to do is we're going to squeeze the tips together and pop it loose. inaudible 00:08:44 together. We want to do all three.Now if you notice on our shield here, I've got it marked. This is going to have to be cut out, but if you notice that our bumper beam is in place. We're going to end up taking this off, so I just marked this so I remember to cut this after I get this out. The other side is just going to be a square. This is a solid piece. It's not going to have this to cut.Right here in the bottom corner of the part we're going to be trimming on our louvered housing, we're going to pop this fastener out. We're going to do the same thing on the other side. We're going to have our ambient temperature sensor. We're going to pop it loose, and you can use a flathead screwdriver or trim-panel tool. We're going to have two 8mm-head bolts to remove. And then we're going to have two squeeze fasteners at the top. Go ahead and squeeze those. Make sure you check for any other wiring. It looks like we have a wire that comes around up here at the top. Let me put that. Then we have some other fasteners here. We got another one over here on the side. We'll go ahead and pull this off and set it aside.Here, we're going to have two tack welds. We're going to do that on both sides. We're going to take, and we need to drill them out. I'm going to start with a small drill bit to give me a pilot hole first, and then I'm going to go with a bigger one so I can get the whole thing out. We're going to do that same thing on the other side. We'll take a 13mm socket. We're going to have four bolts on each side of the bumper core that need to remove: these two and then two inside the holes. Then remove your bumper core. This is not going to be re-installed, but if you ever plan on putting it back on, you may want to hold onto this and the hardware you just took off.Now we're going to set our base plate in place. We're going to line it up with the four holes on our frame rail. We're going to use the existing hardware that we took out of the bumper beam. We want to make sure we add Loctite on all of our hardware that we're installing on the base plate. We're not going to tighten these down all the way. We're just going to loosely install them for now.Next, we're going to have two brackets that look like this. This, you notice how the bracket has one side that has a welded-on piece. This piece is going to go towards the outside. This is going to sit on the sub-frame. These two holes line up with two holes on the base plate. Take our short, hex bolt, Loctite. We're going to have two of them on each side. We're going to line them up with the holes from the bottom. Put on a lock washer and then a nut.Next, we'll take our long hex bolt. We're going to slide on a flat washer. You're going to have a pipe spacer. It looks like this. There's a large hole that goes all the way through and then through the bracket. We're going to take our bolt. We're going to come up from the bottom. We're going to slide our pipe spacer in between. We want our bolt to go through it and then up through the bracket. inaudible 00:14:11. We'll put on a lock washer and our nut. A 3/4" socket and wrench. We're going to tighten and torque all of our hardware to the specification in the instructions.On the back of our louver housing, the lower four louvers, we've got to remove. If you flip it over on the backside, you're going to have this little bracket. We're going to pop it loose. We're going to pop our louvers from the center just like that. Then we're going to remove them. Now we need to cut out our areas that we have marked on our louvered housing. Once we get it cut, we'll do a test fit, make sure everything's fitting correctly. Then we're going to reinstall it in reverse order from the way we took it off. For these, where there we're screws, we actually have bolts, two flat washers, and a lock nut.On your passenger side, you're going to have our ambient temperature sensor that we need to re-install. Once you have your hardware tightened and torqued to the specification in the instructions, it's a good idea, before you put your fascia back in place, go ahead and add any additional wiring like your diode wiring kit or braking system that you want to add. It's going to be a lot easier to run all your wires to the front of the vehicle.Once you put your fascia back in place, you're going to have to do some trimming or some modifications. Be sure, when you put this back in place, you hook up to any wiring that you disconnected. You have the plug on the top for your louvers. You also have your fog lights. Also, another thing I want to mention is when you're putting this back in place, it's a good idea to tape your edges. Tape the edge of your fascia. Tape the edge of your fender, so that when you're putting this back in place, when these two sides meet, they're not scratching each other.Again, I'm Shane with etrailer.com. I hope this video has helped you, whether you're still deciding or installing the Roadmaster Crossbar-Style Base Plate on your 2017 Ford Taurus.
Ratings & Reviews

Robin
11/25/2025
Working great these are durable tow bars Have no problems with them easy to hook up and tows vehicle without no problems .

Robert
1/7/2026
Everything related to my Mini towing system is working great after a year of use.i do wish I had bought a cover for the tow bar though. Keeping it clean would be easier with the cover. Great products and service from etrailet

Claire H.
7/6/2026
It really is invisible! It took me a second to even find the base plates in your photo!

James
7/3/2026
New system working fine. As with previous system it requires towed vehicle to be nearly perfectly aligned straight behind motorhome to disconnect without considerable tension.

David
5/24/2026
It continues to work flawlessly

Christopher H.
8/4/2026
Thanks for you feedback Thomas! Sounds like the install went smooth. Hope you have a great summer!

Claire H.
5/7/2026
Thank you so much for the kind words and being a repeat customer with us! We look forward to helping you out with all your future adventures!

Rob
1/21/2020
Everything is working great, I installed a base plate kit, battery charging kit, stop light switch kit, second vehicle air brake kit w brakeaway and seat adapter on our 2019 Chevy Equinox and towed it about 14000 miles behind our motor home this past year and everything worked perfect not a problem with any product. These are great products, everything fit perfectly and performed perfectly. Thank you for great service and great products. Rob

Chris
3/16/2020
It’s been a year now and probably 7,000 miles later and everything has held up perfectly despite some darn rough roads between MD and Albuquerque, NM and back.

Bill F.
10/15/2016
Hate that every 3,000 miles towing have to re-torque bolts of base plate. Good product otherwise.


Bob T.
4/20/2015
This item works great. Have towed about 4500 miles using it. I couldnt be happier with the results.

J.c. R.
7/24/2019
Other than the clearance of the mounting bracket I noted in my original review, the base plate worked out fine on the Kia. I ended up replacing the Kia with a new Subaru. I was able to buy a Blue Ox base plate for it and all mounting hardware is up and out of the way of obstacles.

Sanfordturbo
8/23/2021
Over the past year, i have towed the Fiat behind the motor home for 15000 miles or so. Rock Solid. Highly recommend. Ive had 2 blow outs on the motor home and the tread bounces off the Road Master Guardian without damaging the Fiat. The Guardian is scuffed and scratched and handling it well.

Jeffrey
10/29/2018
Base plate has been working out great. Easy putting on and taking off.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.










Kate F.
5/14/2026
Thanks for the review and for sharing your installation experience Christian. Your tip about leaving the bumper on during install is really helpful, especially since fitting the ends through the louvers can take a little extra maneuvering. It’s also great to hear the setup works well with your Stowmaster 5000. The install looks great, and we appreciate you sharing the picture! Where did you go for the first trip?