Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
If you want your trailer setup to look sharp while standing up to the elements, this 15" x 6" aluminum wheel in a matte black machined finish delivers both. The bold design gives a modern upgrade without sacrificing toughness, and the corrosion-resistant surface helps it keep that clean appearance through seasons of use on the road or near the water.
This wheel uses steel inserts in the lug nut wells to prevent wear around the mounting holes. The inserts are pressed into the aluminum, helping the wheel stay firmly secured over time so you don’t have to constantly retorque the lug nuts after trips. It’s a small but crucial detail that protects both the wheel and your peace of mind.
Swapping from steel to aluminum means less rust and easier handling without giving up strength. The lightweight build keeps performance consistent under load, while aluminum’s natural resistance to corrosion makes it ideal for long-term reliability.
The 15" diameter and 6" width give you solid footing for most trailer setups, and the common 5 on 4-1/2 bolt pattern fits many popular hubs. That combination provides a dependable foundation for confident towing mile after mile.
1. Count the lug holes
Look at the wheel hub or the back of the wheel and count how many lug holes there are(also called bolt holes).
Common configurations include: 4-lug, 5-lug, 6-lug and 8 lug
2a. For even lug counts (4-lug, 6-lug, 8-lug)
Measure from the center of one lug hole directly across to the center of the hole opposite it.
Common configurations: 4 on 4", 6 on 5.5", 8 on 6.5"
2b. For odd lug counts (5-lug)
Measure from the center of one lug hole to the outer edge of the hole directly across (not center-to-center since there's no directly opposite hole).
Common configurations: 5 on 4.5" (most popular), 5 on 5", 5 on 4.75", 5 on 5.5"
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello everybody, this is Jeff at etrailer. Today we're gonna take a look at this Lionshead 15-inch by 6-inch Liger, matte black, aluminum trailer wheel. That's a five on 4-1/2-inch bolt pattern. Now this is an aluminum wheel. It's very durable, lightweight, and rust proof. And we mentioned the design.
It's an attractive Liger series, which you can see is a nice five-spoke design, has a nice all matte black finish to it. And then if you look on the spokes right on the edge of the spokes here, it has a machine finished on the edge, gives a little shine to the wheel. They do use an automotive grade clear coat finish on the front to help protect from scuffs and scratches. One of the nice features I like on this wheel is they use these steel inserts here in the lug nut wells and that's designed to help keep your wheel securely in place on the trailer hub. Those steel inserts help prevent your holes from elongating when you torque down your lug nuts and eliminates the need for constant re-tightening of the lug nuts.
If you notice right over here, it does include the valve stent, which is all installed, ready to go. Now it does not come with the center cap. If you do want a center cap, we do sell those separately on our website. You do wanna make sure to get one that'll have the same diameter as this pilot hole right here. 'Cause when you install that center cap, it'll go through this hole.
The diameter on the pilot hole is 3.19-inches. Now this wheel does meet the DOT, Department of Transportation, specification and it meets the SAE J1204 standards. A few dimensions on this, when we say 15-inch diameter, what we're measuring is inside to inside or bead seat to bead seat. So you can see if we take our tape measure and if we go all the way across, there's your 15-inch diameter. The width on the wheel is gonna be the same way.
It's measured inside the inside or bead seat to bead seat. So there's your 6-inches wide, and this wheel does have a bulk pattern of five on 4-1/2-inches, you can see here. And if you wanted to measure the bolt panel on a wheel like this, it's an odd number of lugs. In this case, five. What you have to do is pick any one of the holes, let's say this hole here, and then you're gonna measure across to either one of these holes. But when you measure, it's from the center of the starting hole to the furthest edge of whichever hole you measure to. So on this one, if we measure, it'd be 4-1/2-inches. So that's on, it's a five on 4-1/2-inch bolt pattern. Does use a wheel lug size of a 1/2-inch by 20, and the weight capacity on this wheel is 2,200 pounds. Now if you do have any other additional questions regarding this part or any other item that we carry, please feel free to reach out to us so we can help you get all your questions answered for you. But that is gonna do it for a look at this Lionshead, 15-inch by 6-inch Liger, matte black, aluminum trailer wheel with the five on 4-1/2 inch bolt pattern.
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
Ratings & Reviews
Ruth L.
5/30/2026
Still as great a when we bought it a year ago. This trailer is stored outside in the desert of Las Vegas & it still looks brand new.
Coy
8/16/2025
Still looks like new. Looks just like the rims that came on my 5th wheel.
Brent
6/25/2022
Excellent, no issues at all.
Christian
4/2/2026
I now have new heavy duty tires mounted and hopefully no more problems.
Do you have a question about this Trailer Tires and Wheel?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Lazer S.
10/12/2026
Glad you like them, James! I always liked the look of black wheels on a camper! ^___^ What kind of camper did you install these on?