Track your water use down to the liter with this flush mount gauge. It gives you real-time readings on a bright display as water leaves your tank, and the included adapters help connect it to your RV plumbing
Factory panels often leave you planning around rough estimates, not the water you've got left. This Topargee flush-mounted gauge tracks freshwater use through an in-line hose installation and shows exact water levels in liters or gallons on a backlit LCD display. As water runs for dishes, showers, or camp cleanup, you're watching a number change on the screen instead of trying to read a vague tank indicator.
Retrofitting a gauge gets a lot less painful when tank access is tight or drilling into your tank isn't on the menu. This setup connects directly to your hose line, with no drilling or tank access required, and uses a 4' 6" sender lead for routing from your plumbing to your display location. Once it's plumbed into the line, your tank stays untouched while your gauge reads water use from the hose run.
Thread mismatch is one of those driveway install surprises that slows the whole job down. This kit includes adapter fittings for joining 1/2" BSP female thread to a 1/2" NPT male connection, plus a Flair-It swivel female adapter with a 1/2" female pipe thread end and 1/2" barb for 1/2" PEX, polybutylene, or polyvinyl tubing. Lay out your cut point, confirm the sender direction and fitting order, then tighten the plumbing connections before pressurizing the line and checking for leaks.
A loose surface display doesn't always fit when the rest of your controls are built into your panel. This gauge mounts recessed into your dash or interior panel and runs on a 12V hardwired connection instead of batteries. The large backlit screen stays readable in daylight and after dark, so checking your freshwater level during an early morning fill or late-night stop just takes a quick glance at the panel.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi, everyone. Steve here with etrailer. Today we're taking a look at the Topargee Flush-Mounted Water Tank Gauge with included adapter fittings. So folks, if you've ever had your tank panel say full all morning, and then all of a sudden later on you've got no water halfway through doing dishes or something like that, you already know what the problem is, right Unfortunately, most factory gauges just are not accurate. They read in big jumps, full, 3/4, 1/2, so forth, so you're gonna end up guessing instead of actually knowing how much water you truly have. So that's where this to Topargee Flush-Mount Water Tank Gauge changes everything.
So instead of guessing tank levels, this system, with all the connections and the reader here, is going to measure actual water flow so you can see exactly how much water you're using in real time, rather than, whether it's a quick shower, brushing your teeth or rinsing off gear. And one of the biggest advantages to this installation, instead of drilling into your tank, this unit installs directly into the water line with this guy here, the fittings, if you need them, depending on what your setup is, and all the installation screws for mounting the flush unit to the wall. So that's gonna keep your tank intact. It's gonna make it set up cleaner and easier. And it does use a backlit display.
It's not powered up, obviously. That's gonna give you clear, precise readings. And because it installs in line with the water system, again, you're not drilling into your tank. Now, with this, you're gonna know exactly what a normal day looks like over a few times of using your water daily. And that way when you check the display, the numbers are actually gonna line up with what you expect, what you're used to, and there's no surprises.
And it is fully programmable to your tank size. So you'll enter your tank size, and then based on the water usage it's reading, it's gonna give you accurate tracking down to the gallon so you don't have to guess how much water you truly have left. So folks, a great option for you. This is the Topargee Flush-Mounted Water Tank Gauge with the included adapter fittings. I'm Steve with etrailer.
Thanks for watching. And if you don't wanna do the install yourself, check out our installation locator link below, and we can help pair you with a trusted etrailer installer in your area.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.