Rhino-Rack Heavy Duty Roof Rack for Raised Rails - Aluminum - Silver - Qty 2

See what our Experts say about this Rhino Rack Roof Rack

• Does Rhino-Rack HD Roof Rack for 2020 Toyota Corolla Sedan Have Static Load Rating
  I checked with Rhino-Rack and they specifically mention they only have dynamic (moving) load ratings, and that is exactly what the 165 lb capacity is with the rack that fits your 2020 Toyota Corolla sedan. Rooftop tents generally only call for a rack to have a certain dynamic capacity so I recommend checking out your tent's manual to find out. As for the roof rack for your 2020 Toyota Corolla, here are the parts you need: - Rhino-Rack Heavy-Duty Roof Rack Crossbars # # RB1250B-2 (Black)...
  view full answer...
  
• Dimensions of Rhino-Rack Heavy-Duty Roof Rack Crossbars
  The Rhino-Rack Heavy-Duty 50-Inch Roof Rack Crossbar # RB1250S has cross-section dimensions of 1-7/8-inches tall and 1-5/8-inches wide, as shown in the photo I prepared for you. We also offer two bars as a set # RB1250. The vehicle known as the Mitsubishi Pajero in other countries is called the Montero in the North American market. If you happen to have a 2006 model year with factory installed roof rails that run front-to-back this crossbar can be installed using leg kit part # CXB.
  view full answer...
  
• Can I Carry Two Kayaks Side by Side on My Roof Rack?
  The roof rack you're asking about is a Rhino-Rack System with parts # RB1250, # RRRLKHD, # DK376 which has 50" long crossbars. As for if you can carry two kayaks lying down side by side, it's unlikely, but depends on your kayaks. Kayak widths can range from 22" to 30". If you have saddle-style kayak carriers like the Malone SaddleUp Pro # MPG110MD and your kayaks are less than 24" in width, then you can set them up side by side. If your kayaks are too wide though, you can get two J-style...
  view full answer...
• Crossbar Pads to Carry a Surf Board on Rhino-Rack Heavy Duty Crossbars
  Yes, we do have foam pads that will fit around your Rhino-Rack Heavy-Duty Roof Rack Crossbars # RB1250 and allow you to carry your surf board. You can use the Rhino-Rack Crossbar Pads w/ Tie-Downs # RRRWP04. These pads will fit your HD crossbars. I have included a picture from the instructions manual that shows this as a fit.
  view full answer...
  
• 2017 Hyundai Tucson Heavy Duty Roof Rack Recommendation
  Thank you for all of the info! I definitely have a roof rack solution so you can carry some ladders with your 2017 Hyundai Tucson but at this time (February 2022) Rhino-Rack doesn't have a roof rack fitment for your Tucson so we won't be able to install a roof rack using the Rhino-Rack Heavy-Duty Roof Rack Crossbars # RB1250. As an alternative option I recommend going with the Yakima HD Crossbar roof rack system. The crossbars won't increase the weight capacity of the roof rack since your...
  view full answer...
• Is Rhino-Rack 2500-Series Roof Rack Compatible with Thule Force Cargo Box # TH624
  The Rhino-Rack 2500-Series roof racks can include either square Euro crossbars, their Vortex Aero bars or their heavy-duty rectangular bars. The Euro square bars and the Vortex Aero bars both are fully compatible with the Thule Force XT Cargo Box # TH6356B. The heavy-duty cross bars # RB1250 are not. The Thule Force XT requires that the spread between the crossbars be at least 23-5/8-inches. As long as the rack has this minimum spread and uses one of the two compatible bar types it will...
  view full answer...
• Can I Use The Batwing Awning # RR33200 With My Factory Crossbars?
  The Rhino Rack Batwing Awning # RR33200 is a bolt on installation so it won't be able to work with your factory crossbars. You'll need to add another roof rack system with tracks to be able to use the batwing awning. You can use something like these legs # CXB and these bars # RB1250. These have a channel which will work with the hardware on the Batwing. You will need this mounting kit # RR31102. I personally have not used the XTM 270 Batwing Awning before. So I think that the batwing...
  view full answer...
• What are the Dimensions of the Hi-Lift Jack Mounting Brackets # RJHB
  I went out to the warehouse and found that the internal dimension of the Hi-Lift Jack Mounting Brackets # RJHB would allow a post that is about 1" thick and about 2-3/4" high. These come with T-bolts that let you mount them on Rhino-Rack Heavy-Duty roof-rack crossbars like part # RB1250.
  view full answer...
  
• How to Determine if Rhino-Rack CXB Leg Kit Fits a 2022 Subaru Forester for HD Bars & Roof Top Tent
  The Rhino-Rack CXB Leg Kit for Raised, Factory Roof Rack Side Rails # CXB will fit the factory rails on your 2022 Subaru Forester as long as those rails are not more than 1-1/2" tall and not more than 2-1/4" wide. This would allow you to use Rhino Rack HD cross bars like the Rhino-Rack Heavy-Duty Roof Rack Crossbars # RB1250. It is also important to note that since these use the Rhino Rack HD bars, you may have a difficult time finding a rooftop tent that fits. That is because the HD bars...
  view full answer...
• Weight Capacity Of The Rhino Rack RLTF Roof Rack System.
  If you used these # RLTF feet with the tracks # RRRTV188 and use the Heavy Duty Crossbars # RB1250 you will have 220 lbs of capacity on your roof. This is a bit more than the average roof rack system so you will be able to really fill up your bar space! You should verify that the vehicle's roof can handl that weight too though.
  view full answer...
• Sturdy Roof Rack Recommendation for 2008 Chevy Cobalt
  For a vehicle like your 2008 Chevy Cobalt I would not want to recommend a track style of rack as the best option. The tracks aren't going to flex enough to fit well and the clamp style racks are much sturdier than one might think so even though that's not the option you listed wanting it would be your overall best option still. Rhino Rack does offer a heavy duty roof rack that fits your vehicle with the # RB1250, # RRRLKHD, and # DK181 if you have a sedan or part # DK182 for a coupe but...
  view full answer...
• Will the Inno Shadow 16 Fit on Rhino-Rack Crossbars on My 2013 Toyota Prius?
  As far as the fitment of the Inno Shadow 16 Cargo Box # INBRA1210BK being able to clamp around a Rhino-Rack roof rack, it depends on what type of Rhino-Rack crossbars you have on your 2013 Toyota Prius. If you have an aero crossbar system that involves the Rhino-Rack Vortex crossbars like the ROC25 # RR44SR, the Shadow 16 will clamp around those as well. The only caution is that the Shadow 16 will not fit Rhino-Rack Heavy Duty Crossbars like the # RB1250. I am happy to say that all 4...
  view full answer...
  
• Heavy Duty Roof Rack Recommendation for 2013 Hyundai Sonata
  For stuff like lumber from a home center type store I would recommend the Rhino Rack HD roof rack part numbers # RB1250, # RRRLKHD, and # DK250 as it is confirmed as a fit and has large square bars that are great for what you are looking for. For load stops you would then want the pat # RRRLH1. Then for cinch straps part # RRRTD35P. This rack has a capacity of 110 lbs but you would also need to check the roof capacity of your vehicle in the owners manual.
  view full answer...
• Will the Rhino-Rack HD Crossbars Allow Me to Transport 2 Kayaks on My 2014 Kia Sorrento LX?
  Yes, the Rhino-Rack Heavy-Duty Roof Rack Crossbars - Black - 50" Long - Qty 2 # RB1250B-2 (black) and # RB1250 (silver) are compatible with the bare roof on your 2014 Kia Sorrento LX without a vista roof. For a complete roof rack system, you will need the following parts: - Rhino-Rack 2500 Series Legs for Heavy-Duty Crossbars - Naked Roofs or Fixed Mounting Points - Qty 4 # RRRLKHD - Custom DK Fit Kit for 4 Rhino-Rack 2500 Series Roof Rack Legs - Naked Roof # DK179 For a J-style carrier...
  view full answer...
• Will the Rhino-Rack RTC-Style Roof Rack Tracks # RTC95JW Fit a 1998 Jeep Wrangler with Hardtop
  The 37-1/2" long Rhino-Rack RTC-Style Roof Rack Tracks # RTC95JW are a universal fit so as long as your 1998 Jeep Wrangler Sahara has a naked roof that is flat then they will fit. The tracks provide mounting points for the Rhino-Rack # RLTP, # RLTF, and # RLT500 track-mounted legs. These are compatible with the Heavy-Duty Rhino-Rack Bars like the 50" long # RB1250.
  view full answer...
• How Do Roof Racks Attach to a 2012 Hyundai Elantra
  Rhino-Rack 2500 Series Leg Kit # RRRLKHD is just the legs but for them to actually fit your 2012 Hyundai Elantra you need the proper clamp kit. If you have a 4-door sedan with no rails or crossbars already on the roof you would use clamp kit # DK301 and bars # RB1250. If you have a Touring model with no rails or crossbars you would use clamp kit # DK010 and bars # RB1250. Clamp kits have what is basically a hook that attaches to the roof right above the doors in the door jamb. If you...
  view full answer...
• Leg Spacers for the Rhino-Rack RCH Legs
  If you're looking for the leg spacers to mount Heavy-Duty crossbars to your RCH Legs, part # RRRCH6, then the correct part number for those are # RRQMHD05. With these, you'll be able to mount Rhino-Rack HD Bars, part # RB1250. This may seem confusing at first because the fit-guide states that these are not compatible with your 2007 Lexus GX 470. However, in this particular (and very rare) case, the specific vehicle does not matter because these are attaching to the legs. In other words,...
  view full answer...
• Will the 65" Rhino-Rack HD Crossbars # RB1650 Fit on My 2010 Mazda 3 Hatchback?
  I have an answer for you. Unfortunately, the 65 inch Rhino-Rack Heavy-Duty Roof Rack Crossbars # RB1650 are too long for your 2010 Mazda 3 Hatchback with fixed mounting points. With that being said, you can still have shorter Rhino-Rack Heavy-Duty crossbars on your vehicle. Our installation team here at etrailer has tested these shorter bars with your vehicle so that they will fall within the required dimensions of local traffic laws. For this system, you will need the following parts:...
  view full answer...
• Roof Rack Recommendation to Carry 2 Kayaks on 2014 Toyota Prius C and 2010 Toyota Prius
  There is a Rhino Rack roof rack that will fit both vehicles if you switch out the Custom DK Clamps and Pads. For the 2010 Toyota Prius, you will want the following parts: Crossbars # RB1250 Leg Kit # RRRLKHD Custom DK Clamps and Pads # DK195 For your 2014 Toyota Prius C you will want to add Custom DK Clamps and Pads # DK351. Before you attempt to carry 2 kayaks on the roof of your Prius you will need to consult your owner's manual to determine if you have the carrying capacity for...
  view full answer...
• Recommendations for Rhino-Rack HD Roof Rack on a 2013 Volkswagen Jetta Sedan
  I am happy to help you find a roof rack for your 2013 Volkswagen Jetta Sedan. For naked roofs, the roof rack will mount to the door frame of your vehicle using a custom fit hook. The Rhino-Rack HD # RB1650 does not have a confirmed fit custom mount for your Jetta, but the # RB1250 does. You will need the legs # RRRLKHD and custom fit kit # DK055 to complete your roof rack system. Check out the video below for a detailed explanation on how these racks are installed and why the custom...
  view full answer...
• Rhino-Rack Heavy Duty Roof Rack for 2018 Volkswagen Passat
  The Rhino-Rack # Y01-140B-NT is designed to fit roof mounted tracks such as what would be found on a camper shell, it's not typically used on a vehicle roof. You can install a similar rack using the following parts: • Rhino-Rack Heavy Duty 50 inch crossbars, part # RB1250B-2 for black or # RB1250 for silver • Series 2500 Legs, part # RRRLKHD • Vehicle-Specific fit clips, part # DK323 This rack has a 165 lb capacity and is custom designed to fit your vehicle.
  view full answer...
• Parts Needed to Move Rhino-Rack 2500 Series Roof Rack to 2014 Toyota Prius C
  A vehicle-specific portion of the Rhino-Rack roof racks for your 2014 Toyota Prius C is the Custom DK Clamps and Pad kit # DK351 that you referenced and this kit is used for a number of their 2500-series racks. You may also need a leg kit; which one will depend on the crossbars you have (the 2500 series includes several types). If you have the heavy-duty crossbar # RB1250 you will use leg kit # RRRLKHD; if you have Aero crossbars you'll instead use # RRRLKVA. The link provided will show...
  view full answer...
• Availability of Rhino-Rack Heavy Duty Roof Rack Option for 1997 Nissan Pathfinder w/ Roof Tracks
  We do indeed have a system that would work on your Pathfinder. In order to use the Rhino Rack Heavy Duty 50 inch long crossbars on your 1997 Pathfinder, you would use the leg system Rhino Rack specifically designed for the recessed roof tracks, part # RLTFMV. The rack has a 220 lb capacity, which could be limited by the roof's actual capacity if it's lower than that of the rack.
  view full answer...
• Foot Kit for Rhino Rack HD Bar to Fit Raised Rails of 2025 Subaru Crosstrek
  Hey Jeff, the correct leg kit for raised roof rails for Rhino Rack HD crossbars is the part # CXB. This would be the correct kit to use for your 2025 Subaru Crosstrek. How long of crossbars do you have?
  view full answer...
• Dimensions of Rhino-Rack Heavy-Duty Roof Rack Crossbars
  The Rhino-Rack Heavy-Duty 50-Inch Roof Rack Crossbar # RB1250S has cross-section dimensions of 1-7/8-inches tall and 1-5/8-inches wide, as shown in the photo I prepared for you. We also offer two bars as a set # RB1250. The vehicle known as the Mitsubishi Pajero in other countries is called the Montero in the North American market. If you happen to have a 2006 model year with factory installed roof rails that run front-to-back this crossbar can be installed using leg kit part # CXB.
  view full answer...
  
• Roof Weight Capacity of 2005 Toyota Highlander Fitted with Rhino-Rack Heavy Duty Roof Rack
  The Rhino-Rack Heavy Duty Roof Rack for your 2005 Toyota Highlander, which consists of parts # RB1250B-2 and # CXB, does carry a 200-lb weight rating. Your vehicle itself will also have a roof weight capacity that could be more, the same or less. Your manual's indicated weight limit of 100-lbs could be for an OEM roof rack, or it could be for the overall roof structure itself. If Toyota says the roof itself can handle 100-lbs and no more, then you will have to abide by that lower rating....
  view full answer...
• Can I Use The Batwing Awning # RR33200 With My Factory Crossbars?
  The Rhino Rack Batwing Awning # RR33200 is a bolt on installation so it won't be able to work with your factory crossbars. You'll need to add another roof rack system with tracks to be able to use the batwing awning. You can use something like these legs # CXB and these bars # RB1250. These have a channel which will work with the hardware on the Batwing. You will need this mounting kit # RR31102. I personally have not used the XTM 270 Batwing Awning before. So I think that the batwing...
  view full answer...
• How to Determine if Rhino-Rack CXB Leg Kit Fits a 2022 Subaru Forester for HD Bars & Roof Top Tent
  The Rhino-Rack CXB Leg Kit for Raised, Factory Roof Rack Side Rails # CXB will fit the factory rails on your 2022 Subaru Forester as long as those rails are not more than 1-1/2" tall and not more than 2-1/4" wide. This would allow you to use Rhino Rack HD cross bars like the Rhino-Rack Heavy-Duty Roof Rack Crossbars # RB1250. It is also important to note that since these use the Rhino Rack HD bars, you may have a difficult time finding a rooftop tent that fits. That is because the HD bars...
  view full answer...
• Replacement Security Key/Wrench for Rhino-Rack CXB Legs
  It sounds like you are looking for either the standard length replacement Rhino-Rack security key, # SECKEY-S, or the long version, # SECKEY-L. Either one will work despite the difference in handle color.
  view full answer...
• 2013 Pathfinder Naked Roof Roof Rack Recommendation
  For your 2013 Nissan Pathfinder the Sportrack Semi-Custom roof rack part # SR1002 has not been confirmed to fit your vehicle, BUT I do have a similar roof rack that would work for you. Instead you would want the Rhino Rack roof rack that consists of part numbers # RB1375B-2 and # CXB if you are looking for the most economical roof rack option around.
  view full answer...
• Rhino Rack Roof Rack Recommendation for a 1996 Nissan Pathfinder with Raised Rails
  There are two different styles of Rhino Racks that are offered for your 1996 Nissan Pathfinder with raised siderails. Either the aero style bars or the HD style bars. The pros to the aero style is that they will offer less wind noise and better fuel mileage, the pros to the HD is the higher capacity that they offer. About 25 lbs increased capacity. For the aero style bars you would want part numbers # RRVA126B-2 and # RRSX006. For the HD style you would want the # RB1120B-2, and # CXB....
  view full answer...
• Roof Rack Fit For 2011 Volkswagen Golf Wagon With Raised Side Rails
  We do have a roof rack solution for you, though I checked with Rhino-Rack about the compatibility of Leg Kit # CXB on your 2011 VW Golf Wagon with raised side rails, and this leg kit is not going to fit your vehicle. There is not a kit that is going to allow you to use the HD bars on your '11 VW Golf wagon, but you can get a brand new rack system for what it would cost to mount your current bars. Instead, I recommend checking out the Malone AirFlow2 Roof Rack # MPG215. The Malone is...
  view full answer...

Do you have a question about this Roof Rack?