To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
These frame-mounted tie-downs keep your camper stable and your truck handling like normal, even on long hauls. By attaching directly to the frame—the strongest part of your vehicle—they spread the camper’s weight evenly and lower the center of gravity. That means no top-heavy sway or shifting when you hit crosswinds or rough roads, just a solid, predictable ride every mile.
When you’re not hauling, you won’t have bulky brackets hanging off your truck. The tie-down arms remove easily, and the remaining brackets sit tucked up against the frame so they’re barely visible. You keep the strength and convenience of a full tie-down system without changing how your truck looks day to day.
The custom design uses pre-existing holes in the frame so installation takes little to no drilling. That means no cutting or permanent modifications and minimal loss of ground clearance. The snug fit mounts tight to the frame for a clean install that stays out of the way but is ready whenever you load your camper.
Made of durable steel with a high-impact powder coat finish, these tie-downs are built to handle tough conditions trip after trip. The finish adds an extra layer of protection against road grime and weather so your hardware stays strong and looks good longer.
Each tie-down arm includes two pin holes so you can extend it just enough to clear fenders or sidewalls and line up perfectly with your camper’s anchor points. Two holes in the attachment plate let you adjust the angle for the best hold. Pair them with turnbuckles (sold separately) for a tight, balanced setup that keeps your camper locked down from multiple directions.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today on this 2008 Toyota Tundra Crew Cab Max, we're going to show you Part Number TLT2304. This is a TorkLift Custom Frame-Mounted Camper Tie-Downs for the front of a truck. A few things to know about these tie-downs, that they provide separate attachment points for the front of your truck bed, left and right side, for securing a bed-mounted camper. Now, the rear tie-downs are sold separately. This does mount to the frame, and when it's not in use, the inserts are completely removable. This is our insert here. We're looking at the driver's side and it has two holes in it for your tie-downs that go up to your camper.
So, you see it goes back into the frame bracket right here. There's a quick-release pin right here, pull it apart, and you can even adjust it. You have two settings that you can use, and we also have about 5/8 of an inch of distance between the body and the insert. Go ahead and remove it out of the way. With the insert out of the way, if we can go ahead and show you the frame bracket.
The frame bracket mounts up at two points, use an existing hole up on top of the spring hanger. It goes through the frame, uses 1/2 inch hardware, and then it actually reuses this spring bolt right here. It attaches on the inside edge of the spring. It also the backside. It also uses all the factory hardware. This is what our driver's side looks like.
Now, I'll go ahead and show you how the passenger side installs. First off, we'll go ahead and loosen up this bolt. Now, we don't remove it, we just loosen it up. We'll go ahead and undo the nut on this side first, and we'll need to use a 19-millimeter socket and possibly a wrench on this side to hold the bolt in place. Then, what we'll do next, is go ahead and unthread the bolt out a little bit, probably about 1/2 inch to 5/8 of an inch, to give us working room to put the bracket in place. Now, this is going to be pretty tight, so probably we want our breaker bar to loosen up this nut.
There's a washer on here; it needs to stay in place. Let's go ahead just back out the bolt, probably about like I said, about 5/8 of an inch. Now we've got this prepared, we'll go ahead and show you the other hole that the bracket uses. This hole on top will be our second mounting point. Now, I did clean it up. There are some sharp edges that bolts can hang up on. I used a 9/16 drill bit just to help clean it out, and that was it. Not really necessary, but sometimes bolts do hang up on the edges. All right, let's go ahead and put our bracket in place. This may be a tight fit, so let's go ahead a rubber mount to help work it in place. All right, and once you've popped it into place over this here, it took considerable force to pop it up. Possible a bottle jack might help push it up as well. Then, I'm using an alignment tool; This can be like a thick screwdriver to help get to the last point, moving around to line up the hole. Then, we'll go ahead and run our hardware from the inside to the outside. We'll install a long hex bolt, a large, flat washer, put those two together, run it through your square hole in the frame right here, and then out through our bracket. Now, still under a little bit of a bind, we can go ahead and use that to our advantage. Let's go ahead and thread the bolt through and the threads will come out. One additional tool that the kit comes with is this bolt leader right here. Basically, on the driver's side, this will help you pull the bolt from the inside to the outside. Essentially, you just thread it on to the end of a bolt, now the threads of our bolt will get a flat washer and a nut. We'll go ahead and run our bolt back through the other side and reinstall the factory nut. Now, the manufacturer recommends you use Loctite and reinstall the factory nut. We'll be using Part Number LT37643, Loctite Blue Stick Threadlocker. Okay, with all our hardware loosely installed, we can go ahead and tighten down the bolts down for good. Now, we're going to tighten up the top bolt. We'll go ahead and put a wrench to hold the place on this side. Now, on a driver's side, when you do that, you'll need a deep well socket for that, and you'll have to reach up like this to get access to it. With our bracket installed on the passenger side, we'll go ahead and install the insert, line up the holes, and put in the clip. All right, that will finish it for our install, Part Number TLT2304, TorkLift Custom Frame-Mounted Camper Tie-Downs for the front on our 2008 Toyota Tundra Crew Cab Max. .
Ratings & Reviews

Lazer S.
9/16/2025
It definitely is safe the way you have them, Paul! In a perfect world, the turn buckles would be perfect vertical, but this an imperfect world and not all campers have the attachment points in the same place. If you take a look at some of the installed pictures on the TorkLift Locking FastGun Turnbuckles # TLS9529-2-LK page, you can see most of them are at an angle. It's perfectly normal. Are you running any suspension enhancement on your Silverado?

Paul
9/27/2026
These tie downs are great, so easy to use. Camper never budged a hair


Bob
11/1/2025
I have not had any issues at all with the tie downs.

Kate F.
8/10/2026
Thanks for the pictures Rich. We will be reaching out =)

Heather A.
4/10/2026
Looks great! What kind of camper do you have?

Lazer S.
10/14/2025
Install looks great, Megan! Especially for it only taking two hours! They were moving. : ) Happy we confirmed what you found as well. Tie downs can be a pain in the rear with all the options out there. Now I do have to ask though, have you guys thought about any kind of suspension enhancement for the rear axle? It's a little hard to tell, but it looks like the back is sagging a bit in your last picture.



Clay
7/31/2026
A year later and I would not do anything different. Absolutely the best system available especially paired with the fast guns. The camper is solid mounted and does not move. Yet can still be off loaded in just a few minutes. Remember good stuff isn’t cheap and cheap stuff isn’t good.


Kate F.
6/5/2026
Great set-up Viviana!! Glad to see you went with the best =) Where did you go for your first trip?

Nick S.
1/12/2026
I love these TorkLift tie downs, and it is great to hear you are liking the quality as well. What kind of truck camper are you going to be running with these?

Kate F.
8/20/2026
We appreciate the kind words Charles! Where did you take the in-bed camper for the first trip?

Gwendolyn Y.
9/18/2025
Install looks great, Dale! Where're you headed off to now?


Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.





Straw
8/24/2026
A year later, no issues with tie downs, except normal wear and tear and metal to metal wearrust progression. These tiedowns are designed great and fit function was clearly created by someone who knows not only design but install ! E-trailer is “the” place to buy rv, camper, towing etc products - the install videos are sooooo helpful ! Thx ET !