Most Popular Hitch Cargo Carrier for Toyota FJ Cruiser
change vehicle# 1
24x60 Reese Cargo Carrier for 2" Hitches - Steel - 500 lbs
- view all Hitch Cargo Carrier
- Flat Carrier
- Fixed Carrier
- 24 Inch Wide
- Heavy Duty
- Fits 2 Inch Hitch
- 60 Inch Long
- Class III
- Class IV
- Steel
- Reese
More Information >
by: Thomas05/01/2023
The rack is much bigger than my previous one. I was disappointed that it was made in China instead of the USA. It assembled very easily and the light kit works very well. The only draw back is I can no longer open my tailgate with the rack installed due to the spare tire hitting the raised rack.
View More
View Less
by: James 04/04/2024
Purchased in March 2023. I really like the size, it holds a lot. The carrier is very sturdy, well made and assembled very easily. I purchased the light kit but found wiring could have been a little longer to dress the cables neatly down toward the hitch.
View More
View Less
# 2
19x60 Curt Cargo Carrier for 2" Hitches - Aluminum - Folding - 500 lbs
- view all Hitch Cargo Carrier
- Flat Carrier
- Folding Carrier
- 20 Inch Wide
- Heavy Duty
- Fits 2 Inch Hitch
- 60 Inch Long
- Class III
- Class IV
- Aluminum
- CURT
More Information >
by: Nathaniel02/16/2024
Purchased this 1 year ago. Worked awesome for a 9.000 mile cross country trip with three off road adventures at geology tour road Joshua tree, west side road Death Valley, and kingman wash lake mead. No rattle, always secure, great clearance. Would purchase again.
View More
View Less
by: Randy 03/31/2023
It works, but I only put two electric bikes on it. The mesh seems to bend pretty easy.
View More
View Less
# 3
20 x 59 Curt Cargo Carrier for 2" Hitches - Steel - 500 lbs
- view all Hitch Cargo Carrier
- Flat Carrier
- Fixed Carrier
- 20 Inch Wide
- Heavy Duty
- Fits 2 Inch Hitch
- 60 Inch Long
- Class III
- Class IV
- Steel
- CURT
More Information >
by: Travys08/02/2023
Great quality and serves its purpose. I wish I ordered the slightly bigger one to fit the bins and items I use it for. For example, a white standard igloo cooler doesn’t fit the way I need it to maximize loading capacity. I highly recommend a stabilizer to prevent wobble.
View More
View Less
by: Tyler11/30/2020
Very nice quality. Took one person and two wrench about 15 minutes to install the cargo carrier from box. It is very sturdy and the finish is very good. I really like the added height this specific carrier provides.
View More
View Less
# 4
23x59 Stromberg Carlson Cargo Carrier for 2" Hitches - Steel - 500 lbs
- view all Hitch Cargo Carrier
- Flat Carrier
- Fixed Carrier
- 24 Inch Wide
- Heavy Duty
- Fits 2 Inch Hitch
- 60 Inch Long
- Class III
- Class IV
- Steel
- Stromberg Carlson
More Information >
by: Kent04/11/2024
Carrier and box will be moved to hitch on 209 Solitude Rv to provide extra cargo carrying ability
View More
View Less
by: Thomas A02/21/2020
A good size and very strong. I like the fact that it has a grated bottom, as opposed to a few bars like many of its competitors. There are many holes and notches present for any customization desired. Also makes for a great chair to relax. I also ordered the anti-rattle pin so as to fasten this tightly to the hitch. IMO that should be included with any of these trailer-hitch-Mount accessories.
View More
View Less
# 5
20x48 Reese Cargo Carrier for 2" Hitches - Steel - Folding - 500 lbs
- view all Hitch Cargo Carrier
- Flat Carrier
- Folding Carrier
- 20 Inch Wide
- Heavy Duty
- Fits 2 Inch Hitch
- 48 Inch Long
- Class III
- Class IV
- Steel
- Reese
More Information >
by: Reddog05/03/2023
This is a sturdy carrier. Welds all seem good. Paint is just fine. Steel tubing is very strong. The weight is heavy but reasonable for one person to install and remove. I plan to remove it when not in use on our trip to avoid having to fold it up and lose ability to access the hatch on our van. It has a bit of play in both the receiver and on the folding hinge. I’m going to use construction shims taped in place to reduce the wiggle but even without those, it’s not bad. Even with a jumbo cooler, we can still see the plate. This will do the trick for vacation and camping gear without having to haul a massive 60” carrier. Love the size and build.
View More
View Less
by: Dave B02/03/2017
Product came in a single box in perfect shape. Great construction, easy to put together. I bought this to go on the front of my John Deere Gator 855D. Sometimes, there just isn't enough room to pack everything you need when going down the trail or you don't feel like slinging a Honda generator and a heavy cooler packed full of ice and your favorite beverages up in the back of the bed. This cargo carrier fit the bill perfectly. It took all of 5 minutes to put it together and slide into the front 2" receiver on my gator. With the fold up design, I have 22" of clearance between the ground and the bottom of the carrier when carrier is folded out horizontal. Being the carrier is 48" wide, it is narrower than the gator, so I don't have to worry about trying to squeeze through a tight space in the woods. If the gator will go through the space, so will the carrier rack. When I don't need the carrier, it is a snap to pull the pin, swing the carrier rack 90 degrees up and pop the pin back in. Even when folded into the upright position, you can easily see over the carrier rack. Thanks for making a great product.
View More
View Less
# 6
24x60 Curt Cargo Carrier for 2" Hitches - Steel - 500 lbs
- view all Hitch Cargo Carrier
- Flat Carrier
- Fixed Carrier
- 24 Inch Wide
- Heavy Duty
- Fits 2 Inch Hitch
- 60 Inch Long
- Class III
- Class IV
- Steel
- CURT
More Information >
by: JJDWON07/22/2023
We just installed our carrier. We love that this is going to free up a lot of space for our vacation traveling. Very heavy duty and bigger than i was thinking it would be.The pin that holds the carrier in the hitch was not included. It would have been an added bonus if it was.
View More
View Less
by: Andrey09/09/2022
Easy to assemble, nice and solid cargo tray! Bought it with the hitch bracket. Note: no hitch pin included.
View More
View Less
# 7
Yakima EXO Swing Away Storage System w/ 2 Enclosed Cargo Carriers - 2" Hitches
- view all Hitch Cargo Carrier
- Enclosed Carrier
- Swing Away Carrier
- 23 inch Wide
- Light Duty
- Fits 2 Inch Hitch
- 60 Inch Long
- Class III
- Class IV
- Steel
- Yakima
More Information >
by: Russell 04/16/2023
Very interesting! I am pleased with this purchase. All of this equipment is well built and was designed with ease of use and security in mind. The hitch part is surprisingly pretty heavy, but once it is connected this weight gives the hitch a sturdy feel. The lockers are pretty big and the material though light weight feels like it will hold up to some rough miles and a few bruises. It is so nice to have this much dry secure and easy to access storage outside of our vehicle. Customer service was excellent and delivery times were surprisingly short.
View More
View Less
by: Joe04/14/2022
Very easy to install. Total installation time (not counting taking photos and opening boxes) was approximately 15 minutes. The only issue I encountered was the left handle on the lower rack had a broken piece inside the locking pin assembly. Other than that, everything was quick and smooth for a single person job. This will greatly assist my business by allowing more room for passenger comfort on long trips to and from airports with a large party. Looking forward to putting this to use.
View More
View Less
# 8
Yakima EXO Swing Away Storage System w/ Enclosed Cargo Carrier and Cargo Carrier - 2" Hitches
- view all Hitch Cargo Carrier
- Enclosed Carrier
- Flat Carrier
- Swing Away Carrier
- 23 inch Wide
- Light Duty
- Fits 2 Inch Hitch
- 60 Inch Long
- Class III
- Class IV
- Steel
- Yakima
More Information >
by: Ben04/17/2023
This is the perfect setup for family road trips when you need a little extra dry storage. I mounted this on my Rivian R1S and saw no change in range, as opposed to a roof mount system. I only wish Yakima would incorporate a full-size spare mount for the EXO. Also had a favorable experience with etrailer customer service, as one of the locking pins arrived damaged. They were quick to get a replacement part to me at no cost. I couldn't be happier with the EXO or etrailer. I know that sounds corny, but it's true.
View More
View Less
by: Sprinter weekender03/11/2022
Thanks etrailer The unit arrived as projected,, 4 components all well packaged. The instructions were easily followed and accurate The quality of the construction was good with clean welds and good coating One issue was no keys for the pin locks could be located The design of the attachment is very easy to attach and detachment. You can see the various coolers utilized, couple reasons 1. Larger coolers can’t be accessed, the smaller size allows for open top Access, additionally these can be locked with cable thru handle to Reduce possible theft. I did find the upper tightening knob to be not as secure, as I felt better, In putting a thru bolt and lock but in lue of All in all pleased , we’ll see how it holds up under highway use
View More
View Less
Toyota FJ Cruiser Cargo Carriers Questions
- SUPs are usually pretty long. The Carpod part # M2205-2201 isn't going to be long enough to fit the length of a SUP like what you have.
You are going to have to look into a roof rack mounted SUP carrier like the SUP Taxi part # TH810001 which is a fit for the factory crossbars of your 2014 Toyota FJ Cruiser.
view full answer... - The etrailer trailer hitch mount cargo carrier # e98874 measures approximately 9-1/2 inches from the top of the receiver tube to the top of the side rails nearest the vehicle at 19-1/2 inches back from the center of the pin hole. This can vary slightly though if the hitch receiver is angled slightly up or down. Based on this it would be very close on a 2013 FJ Cruiser but you would need to measure to be sure. Also, when folded up, the carrier is 9 inches from the center of the...
view full answer... - To know if you'll be able to clear the Let's Go Aero BossHog, part # H01472, with the rear door of the 2012 FJ Cruiser, you'll need to measure the length of the rear door and how far off the hitch the door sits. The primary contact point you'll want to worry about is the sides of the carrier, which are 7 inches tall. You'll want to measure from the bottom of the door to the top of your trailer hitch. If you have more than 7 inches, you'll clear the carrier easily and then also...
view full answer... - You'd have to measure from the center of the hitch pin on your 2012 Toyota FJ Cruiser out to the furthest point out on the rear spare to determine if the etrailer carrier part # e98874 will clear it.
If that distance is less than 9-1/2 inches this will fit and clear the spare.
view full answer... - We do offer a range of hitch-mount wheelchair carriers like the Flint Hill Goods # FHG77ZR that you referenced. The best option for you will depend on the weight of your chair.
Trailer hitches such as the one on your FJ have a specific tongue weight rating (tongue weight is downward force on the hitch) and this capacity cannot be exceeded. Your vehicle itself also has a tongue weight rating (indicated in your manual or available from your dealership) that likewise cannot be...
view full answer... - You will need to do some measuring. Measure from the center of the hitch pin hole to the farthest back part of the spare tire on your Cruiser. This will give you the measurement you need to compare to the measurements of the rack. The etrailer Motorcycle Carrier for 2 inch Hitch, item # e98873, has 3 hitch-pin holes. This carrier has a measurement of the first hitch pin hole is 19-9/16" inches from the center of the hitch pin hole to the center of the wheel track and 7-5/16"...
view full answer... - On the etrailer trailer hitch mount cargo carrier # e98874 it measures 19-1/2 inches from the center of the hitch pin hole to the pivot bracket. If you measure on your FJ Cruiser from the center of the hitch pin hole back to the distance needed to clear the rear bumper and it is less than 19-1/2 inches then the carrier will fit when folded down- I am confident this will fit. But when folded up the carrier is 9-1/2 inches from the center of the pin hole-this you will need to check.
view full answer... - Thanks for getting me the hitch pin to end of spare tire clearance your vehicle has. That makes my job much easier.
The etrailer Cargo Carrier part # e98874 just might work for you. When folded up it has a distance of 9-1/2 inches from the center of the hitch pin hole to the nearest railing of the carrier. Basically you would be 1/2 inch shy of clearance so you may want to verify the measurement you took. Otherwise you'd need to use a hitch extender like # e88YR.
view full answer... - You need only take one simple measurement of your FJ Cruiser's 2-inch hitch to know whether or not the Ultra-Fab Dirt Bike Carrier # UF48-979033 will clear your rear-mounted spare tire.
Measure from the center of the hitch pin hole to the rear-most edge of the spare tire. The minimum clearance you need will generally be one inch greater than the distance you measure.
This Ultra-Fab carrier provides 5-inches of clearance from the hitch pin hole so if your hitch-pin-hole-to-tire...
view full answer... - If the weight of your motorcycle and motorcycle carrier is less than the tongue weight capacity for your 2007 Toyota FJ Cruiser then yes, this is feasible. I have personally seen motorcycles being carried on the back of a FJ Cruiser so it is realistic and they do offer trailer hitches and hitch mounted motorcycle carriers so it is also possible.
If you don't already have a trailer hitch then the Curt Trailer Hitch Receiver part # 13367 is what I recommend. It sounds like...
view full answer... - Yes, the 24x60 Pro Series Cargo Carrier for 2" Hitches will fit any 2 inch hitch receiver. The Pro Series Cargo Carrier - Steel - 500 lbs # 63153, is a sturdy carrier that has a nice powder coat finish for rust resistance. This cargo carrier has a raised shank that elevates carrier platform by 2-1/2 inches for improved ground clearance. It has side rails to help keep cargo in place and provide multiple tie-down points for the load.
I recommend using the Anti-Rattle Trailer...
view full answer... - Both the etrailer Motorcycle Carrier # MT70101 and the Ultra-Fab Dirt Bike Carrier # UF48-979033 that you referenced are excellent options to use for carrying your Yamaha TW200 with your 2007 Toyota FJ Cruiser. I think in the picture you mentioned that the customer just had the TW200 propped up against the back of their truck because the bolts would need to be adjusted so that the tire fits between them (whereas in the picture the tire isn't really in the middle of the bolts).
I...
view full answer... - The Carpod Walled Carrier # M2205-01-02 shouldn't have a problem fitting the factory hitch of your 2007 Toyota FJ Cruiser but you need to measure it to be sure. If you measure from the center of your hitch pin to the furthest point out on the rear spare and you get less than 14 inches this carrier will fit and clear easily.
view full answer... - To measure clearance for an accessory installed in the hitch on your FJ you will want to measure from the center of the hitch pin hole rearward to the back edge of the spare tire, which is usually the rear-most part of the vehicle. I linked a helpful article for you that shows exactly how to take this measurement.
The Curt hitch cargo carrier # C18151 when empty and folded up into its storage position will extend back from the hitch pin hole by 9-inches. This is shown in the...
view full answer... - I have a great solution for easy to use retractable tie downs for use with the etrailer carrier part # e98873. For that we have the Erickson Tie Downs part # EM34416 which have S-hook ends, a 1,100 lb capacity, and have easy to use push button retract mechanisms.
You'd only need to use a pair of these and you'd be set. I wouldn't recommend a permanent install set of tie downs on this carrier as there isn't an area designed for the attachment and the rack was designed for the...
view full answer... - The shank on the Pro Series cargo carrier # 63153 is meant to only install with a rise. But the reason that some people have installed it upside down is because the diagram in the instructions, see link, shows the basket being assembled upside down so it is a little confusing.
What I recommend is a carrier with a straight shank such as # CC-100. I included a video of this carrier.
view full answer... - We had a customer who used the etrailer motorcycle carrier part # e98873 that you referenced to carry a TW200 and they used ratchet straps form a bracket on the fork tubes to the anchor points. I really like the idea of the tire-pad-strap you sent a picture of but we don't carry anything like that.
If it were me though I'd go with the tried and true method of attaching tie downs to the handlebars of the bike like with the # EM31353. I grew up with motorcycles and we always...
view full answer... - I believe I have a solution for you but most likely the 32x48 Pro Series Solo Steel Cargo Carrier # PS1040100 that you referenced would interfere with your door opening due to the 4 inches of rise the shank has.
You should check out the etrailer Hitch Cargo Carrier # e98874. I has a 19-1/2" distance from the hitch pin hole to the carrier and has a tilting feature.
I attached a link to installation instructions and a review video for you to check out also.
view full answer...
What our customers are saying:
"First Class merchandise. First Class people. Got my hitch and then my cargo carrier here. Best prices and shipping rates I could find online."